Nanoscale structural investigation of Zn_(1-x)Mg_xO alloy films on polar and nonpolar ZnO substrates with different Mg contents

Zn_(1-x)Mg_xO alloy films are important deep ultraviolet photoelectric materials.In this work,we used plasma-assisted molecular beam epitaxy to prepare Zn_(1-x)Mg_xO films with different magnesium contents on polar(0001) and nonpolar(1010) ZnO substrates.The nanoscale structural features of the grown alloy films as well as the interfaces were investigated.It was observed that the cubic phases of the alloy films emerged when the Mg content reached 20% and 37% for the alloy films grown on the(0001) and(1010) ZnO substrates,respectively.High-resolution transmission electron microscopy images revealed cubic phases without visible hexagonal phases for the alloy films with more than 70% magnesium,and the cubic phases exhibited three-fold and two-fold rotations for the alloy films on the polar(0001) and nonpolar(1010) ZnO substrates,respectively.This work aims to provide references for monitoring the Zn_(1-x)Mg_xO film structure with respect to different substrate orientations.     

Effect of electrically degenerated layer on the carrier transport property of ZnO epitaxial thin films

ZnO films were prepared on (1 1 1) YSZ and (0 0 0 1) sapphire by pulsed laser deposition method. Effect of lattice mismatch on the carrier transport properties of ZnO epitaxial thin films was investigated. The carrier mobility of the ZnO films on YSZ was larger than that of ZnO/sapphire due to smaller lattice mismatch when the thickness was below 150 nm. The effect of electrically degenerated layer on the carrier transport property increased with decreasing the film thickness of ZnO film. The carrier density and electron mobility of 20 nm-thick-ZnO film on either substrate were regardless of the temperature. We concluded that the dominant carrier scattering mechanism in ZnO ultra thin films is double Schottky barriers at the grain boundary and that their height depends on the carrier concentration.     

磁控溅射法制备ZnO/YBCO异质结及电学特性

利用磁控溅射技术在YBCO上沉积ZnO薄膜,获得ZnO/YBCO异质结.测量其不同温度下的电学性质,样品显示良好的整流特性,并且随着温度的升高,ZnO/YBCO异质结电流逐渐增大.     

Polarity effects on ZnO films grown along the nonpolar [1120] direction

The surface electrical properties of ZnO thin films grown along the nonpolar [1120] direction have been investigated by Kelvin probe microscopy on a nanometer scale. Two different charge domains, with a 75 meV work function difference, coexist within the ZnO surface, which is covered by rhombohedral pyramids whose sidewalls are shown to be {1011}-type planes. The presence and relative orientation of the two kinds of charge domains are explained in terms of the atomic arrangement at the {1011} polar surfaces.     

CVD两步法生长ZnO薄膜及其光致发光特性

用CVD两步法在常压下于p型Si(100)衬底上沉积出具有较好择优取向的多晶ZnO薄膜。在325nm波长的光激发下,室温下可观察到显著的紫外光发射(峰值波长381nm)。高温退火后氧空位缺陷浓度增加,出现了一个450~600nm的绿光发光带,发光峰值在510nm。作为比较,用一步法生长的ZnO薄膜结晶质量稍差。在其PL谱中不仅有峰值波长389nm的紫外发射而且还出现了一个很强的蓝光发光中心(峰值波长437nm),退火后同样产生绿光发光带。对这两种绿光发光带的发光机制进行了研究,认为前者源于VO,而后者与O_Zn有密切的关系。     

Effect of annealing on the structural, optical and electrical properties of ZnO thin films by spray pyrolysis

Zinc oxide thin films have been deposited on glass substrates at a substrate temperature of 673 K by spray pyrolysis. The samples are annealed in ambient atmosphere at various temperatures. The effect of annealing on structural, electrical, and optical properties of ZnO films has been investigated. X-ray diffraction patterns show that crystallinity of the ZnO films has been improved after annealing. The morphology of ZnO thin films is studied by atomic force microscopy. The tensile strain (compressive stress) is found to decrease with increase in annealing temperature which indicates the relaxation of tensile strain in ZnO thin films. A decrease in energy band gap is observed with increase of annealing temperature. The mechanism of blue-green luminescence of ZnO thin film has been analyzed. The resistivity is found to decrease with annealing temperature.     

温度对ZnO/Al2O3(0001)界面的吸附、扩散及生长初期模式的影响

构建了一个ZnO沉积在α-Al₂O₃(0001)表面生长初期的模型，采用基于密度泛函理论的平面波超软赝势法进行了动力学模拟.发现在400，600和800℃的条件下界面原子有不同的扩散能力，因此温度对ZnO/α-Al₂O₃(0001)表面界面结构以及ZnO薄膜生长初期模式有决定性的影响.在整个ZnO吸附生长过程中，O原子的扩散系数大于Zn原子的扩散系数，O原子的层间扩散对薄膜的均匀生长起着重要作用.进一步从理论计算上证实了ZnO在蓝宝石(0001)上两种生长模式的存在，400℃左右生长模式主要是Zn螺旋扭曲生长，具有Zn六角平面对称特征，且有利于Zn原子位于最外表面.600℃左右呈现为比较规则的层状生长，且有利于O原子位于最外表面.模拟观察到在ZnO薄膜临近Al₂O₃基片表面处，Zn的空位缺陷明显多于O的空位缺陷. 关键词： 扩散 薄膜生长 2O₃(0001)')" href="#">α-Al₂O₃(0001) ZnO     

纳米ZnO薄膜的激子光致发光特性

报道了纳米ZnO薄膜激子光致发光(PL)与温度的关系。首先利用低压金属有机化学气相沉积(LPMOCVD)技术生长ZnS薄膜,然后将ZnS薄膜在氧气中于800℃下热氧化2h获得纳米ZnO薄膜。X射线衍射(XRD)结果表明,纳米ZnO薄膜具有六角纤锌矿多晶结构且具有择优(002)取向。室温下观察到一束强的紫外(326eV)光致发光(PL)和很弱的深能级(DL)发射。根据激子峰的半高宽(FWHM)与温度的关系,确定了激子纵向光学声子(LO)的耦合强度(ГLO)。     

Effects of temperature-induced stress on the structural,electrical, and optical properties of ZnO:Ga thin films grown on Si substrates

Crystalline ZnO:Ga thin films with highly preferential c-axis oriented crystals were prepared on Si(001) substrates at different temperatures using the reactive magnetron sputtering technique. Effects of temperature-induced stress in ZnO:Ga films were investigated using X-ray diffraction (XRD), atomic force microscopy (AFM), electrical transport, and spectroscopic ellipsometry measurements. XRD results showed that the films were highly c-axis (out-of-plane) oriented and crystallinity improved with growth temperature. The residual compressive stress in films grown at low temperature relaxes with substrate temperature and becomes tensile stress with further increases in growth temperature. Resistivity of the films decreases with increasing stress, while the carrier concentration and mobility increase as the stress increases. The mechanism of the stress-dependent bandgap of ZnO:Ga films grown at different temperatures is suggested in the present work.     

Nitrogen incorporation in homoepitaxial ZnO CVD epilayers

ZnO:N thin films have been deposited on oxygen and zinc terminated polar surfaces of ZnO. The nitrogen incorporation in the epilayers, using NH₃ as doping source, was investigated as a function of the growth temperature in the range between 380 °C and 580 °C. We used Raman spectroscopy and low temperature photoluminescence to investigate the doping properties. It turned out that the nitrogen incorporation strongly depends on both, the surface polarity of the epitaxial films and the applied growth temperatures. In our CVD process low growth temperatures and Zn‐terminated substrate surfaces clearly favour the nitrogen incorporation in the ZnO thin films. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Temperature dependence of excitonic luminescence from nanocrystalline ZnO films

The properties of the excitonic luminescence for nanocrystalline ZnO thin films are investigated by using the dependence of excitonic photoluminescence (PL) spectra on temperature. The ZnO thin films are prepared by thermal oxidation of ZnS films prepared by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) technique. The X-ray diffraction (XRD) indicates that ZnO thin films have a polycrystalline hexagonal wurtzite structure with a preferred (0 0 2) orientation. A strong ultraviolet (UV) emission peak at 3.26 eV is observed, while the deep-level emission band is barely observable at room temperature. The strength of the exciton-longitudinal-optical (LO) phonon coupling is deduced from the temperature dependence of the full-width at half-maximum (FWHM) of the fundamental excitonic peak, decrease in exciton-longitudinal-optical (LO) phonon coupling strength is due to the quantum confinement effect.     

退火对ZnO薄膜晶体结构和ZnO/p-Si异质结光电性质的影响

采用脉冲激光沉积方法在p-Si(100)衬底卜牛长ZnO薄膜,分别在500℃、600℃和700℃下真空退火,采用X射线衍射仪研究了退火对ZnO薄膜品体结构的影响,并测量了ZnO的面电阻和ZnO/p-Si异质结的、I-V特性曲线.研究表明,随着退火温度的升高,ZnO的(002)衍射峰强度逐渐增大,半峰全宽不断减小,同时薄膜内应力减小,ZnO晶粒尺寸变大.表明高温退火有助于ZnO薄膜结晶质量的提高.在没有光照的条件下,异质结的漏电流随退火温度的增加而增大;用650 nm光照射样品时,600℃退火的样品表现出最明显的光电效应,而过高的退火温度会破坏ZnO/p-Si异质结的界面结构,使其光电流变小.所以,要得到性能良好的光电器件,应选取适当的退火温度.     

Effect of excimer laser annealing on the properties of ZnO thin film prepared by sol-gel method

Pristine ZnO thin films have been deposited with zinc acetate [Zn(CH₃COO)₂], mono-ethanolamine (stabilizer), and isopropanol solutions by sol-gel method. After deposition, pristine ZnO thin films have been irradiated by excimer laser (λ = 248, KrF) source with energy density of 50 mJ/cm² for 30 sec. The effect of excimer laser annealing on the optical and structural properties of ZnO thin films are investigated by photoluminescence and field emission scanning electron microscope. As-grown ZnO thin films show a huge peak of visible region and a wide full width at half maximum (FWHM) of UV region due to low quality with amorphous ZnO thin films. After KrF excimer laser annealing, ZnO thin films show intense near-band-edge (NBE) emission and weak deep-level emission. The optically improved pristine ZnO thin films have demonstrated that excimer laser annealing is novel treatment process at room temperature.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Spray pyrolysis deposition of ZnO thin films on FTO coated substrates from zinc acetate and zinc chloride precursor solution at different growth temperatures

ZnO thin films were fabricated using zinc chloride and zinc acetate precursors by the spray pyrolysis technique on FTO coated glass substrates. The ZnO films were grown in different deposition temperature ranges varying from 400 to 550 °C. Influences of substrate temperature and zinc precursors on crystal structure, morphology and optical property of the ZnO thin films were investigated. XRD patterns of the films deposited using chloride precursor indicate that (1 0 1) is dominant at low temperatures, while those deposited using acetate precursor show that (1 0 1) is dominant at high temperatures. SEM images show that deposition temperature and type of precursor have a strong effect on the surface morphology. Optical measurements show that ZnO films are obviously influenced by the substrate temperatures and different types of precursor solutions. It is observed that as temperature increases, transmittance decreases for ZnO films obtained using zinc chloride precursor, but the optical transmittance of ZnO films obtained using zinc acetate precursor increases as temperature increases.     

Composition and morphological characteristics of chemically sprayed fluorine-doped zinc oxide thin films deposited on Si(1 0 0)

Fluorine-doped zinc oxide thin films (ZnO:F) were deposited on Si(1 0 0) substrates by the chemical spray technique (CST) from an aged-solution. The effect of the substrate temperature on the morphology and composition of the ZnO:F thin films was studied. The films were polycrystalline, with a preferential growth along the ZnO (0 0 2) plane, irrespective of the deposition temperature. The average crystal size within the films was ca. 35 nm and the morphology of the surface was found to be dependent on the substrate temperature. At low substrate temperatures irregular-shaped grains were observed, whereas at higher temperatures uniform flat grains were obtained. Elemental analysis showed that the composition of the films is close to stoichiometric ZnO and that samples contain quite a low fluorine concentration, which decreases as a function of the deposition temperature.     

MBE生长ZnO薄膜的结构和光学特性的研究

用等离子体源辅助分子束外延(P-MBE)方法在蓝宝石(0001)面上生长出了高质量的ZnO薄膜,并对其结构和发光特性进行了研究。在XRD中只观察到ZnO薄膜的(0002)衍射峰,其半高宽(FWHM)值为0.18°;而在共振Raman散射光谱中观测到1LO(579 cm-1 )和2LO(1 152 cm-1 )两个峰位,这些结果表明ZnO薄膜具有单一c轴取向和高质量的纤维锌矿晶体结构。在吸收光谱中观测到自由激子吸收和激子-LO声子吸收峰,这表明在ZnO薄膜中激子稳定的存在于室温,并且两峰之间能量间隔为71.2 meV,与文献上报道的ZnO纵向光学声子能量(71 meV)相符。室温下在光致发光光谱(PL)中仅观测到位于376 nm处的自由激子发光峰,而没有观测到与缺陷相关的深能级发射峰,表明ZnO薄膜具有较高的质量和低的缺陷密度。     

纳米ZnO薄膜可见发射机制研究

利用溶胶－凝胶法 （Sol-Gel）制备了纳米ZnO薄膜，获得了高强的近紫外发射室温下测量了样品的光致发光谱(PL )、吸收谱(ABS)、X射线衍射谱(XRD).X射线衍射(XRD)的结果表明：纳米ZnO薄膜呈多晶态，具有六角纤锌矿结构和良好的C轴取向；发现随退火温度升高，（002）衍射峰强度显著增强，衍射峰的半高宽（FWHM）减小、纳米颗粒的粒径增大.由吸收谱(ABS)给出了样品室温下带隙宽度为3.30 eV.在PL谱中观察到二个荧光发射带，一个是中心波长位于392 nm附近强而尖的紫带，另一个是519 nm附近弱而宽的绿带研究了不同退火温度样品的光致发光峰值强度的变化关系，发现随退火温度升高，紫带峰值强度增强、绿带峰值强度减弱，均近似呈线性变化.证实了纳米ZnO薄膜绿光发射主要来自氧空位(Vo)形成的浅施主能级与锌空位(VZn)形成的浅受主能级之间的复合，或氧空位(Vo)形成的深施主能级上的电子至价带顶的跃迁；紫带来自于导带中的电子与价带中的空位形成的激子复合.     

γ-LiAlO2上a面ZnO薄膜的光谱特性研究

利用激光脉冲沉积(PLD)技术在(302)γ-LiAlO₂衬底上成功生长了非极性的a面(1120)ZnO薄膜,光致发光谱(PL)带边发射峰半峰宽仅为115meV.研究了非极性ZnO薄膜光谱特性的面内各向异性,发现随着入射光偏振方向改变,在偏振透射光谱上,吸收边移动了20meV,这与A、B激子和C激子的能量差一致;而在拉曼光谱上,激发光偏振方向的改变导致E₂模式的强度发生明显改变. 关键词： 非极性ZnO 2')" href="#">γ-LiAlO₂ PLD