高质量纳米ZnO薄膜的光致发光特性研究

报道了利用低压-金属有机物化学气相沉积技术生长纳米ZnS薄膜，然后，将ZnS薄膜在氧气中于800℃温度下进行热氧化制备高质量纳米ZnO薄膜.x射线衍射结果表明，纳米ZnO薄膜具有六角纤锌矿多晶结构.室温下观察到一束强的紫外(3.26 eV) 光致发光和很弱的深能级发射.根据激子峰的半高宽度与温度的关系确定了激子-纵向光学声子（LO）的耦合强度（ГLO）.由于量子限域效应使ГLO减少较多. 关键词： 光致发光 热氧化 激子 纳米ZnO薄膜     

纳米ZnO薄膜的激子光致发光特性

报道了纳米ZnO薄膜激子光致发光(PL)与温度的关系。首先利用低压金属有机化学气相沉积(LPMOCVD)技术生长ZnS薄膜,然后将ZnS薄膜在氧气中于800℃下热氧化2h获得纳米ZnO薄膜。X射线衍射(XRD)结果表明,纳米ZnO薄膜具有六角纤锌矿多晶结构且具有择优(002)取向。室温下观察到一束强的紫外(326eV)光致发光(PL)和很弱的深能级(DL)发射。根据激子峰的半高宽(FWHM)与温度的关系,确定了激子纵向光学声子(LO)的耦合强度(ГLO)。     

Near infrared to UV dielectric functions of Al doped ZnO films deposited on c-plane sapphire substrate using pulsed laser deposition

Transparent conducting polycrystalline Al-doped ZnO (AZO) films were deposited on sapphire substrates at substrate temperatures ranging from 200 to 300 °C by pulsed laser deposition (PLD). X-ray diffraction measurement shows that the crystalline quality of AZO films was improved with increased substrate temperature. The electrical and optical properties of the AZO films have been systematically studied via various experimental tools. The room-temperature micro-photoluminescence (µ-PL) spectra show a strong ultraviolet (UV) excitonic emission and weak deep-level emission, which indicate low structural defects in the films. A Raman shift of about 11 cm⁻¹ is observed for the first-order longitudinal-optical (LO) phonon peak for AZO films when compared to the LO phonon peak of bulk ZnO. The Raman spectra obtained with UV resonant excitation at room temperature show multi-phonon LO modes up to third order. Optical response due to free electrons of the AZO films was characterized in the photon energy range from 0.6 to 6.5 eV by spectroscopic ellipsometry (SE). The free electron response was expressed by a simple Drude model combined with the Cauchy model are reported.     

Structural and optical properties of nanocrystalline ZnO thin films synthesized by the citrate precursor route

Nanocrystalline zinc oxide (ZnO) thin films have been deposited by spin-coating polymeric precursors synthesized by the citrate precursor route using ethylene glycol and citric acid as chelating agents. The ZnO thin films were annealed in air at different temperatures for 10 min. The films were characterized by different structural and optical techniques, including X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmission spectroscopy, and photoluminescence (PL). The thermal decomposition of polymeric precursor was studied by thermogravimetric analysis (TGA). XRD analysis with grazing incidence and rocking curves indicate that the ZnO films are polycrystalline with preferential orientation along the c-axis direction with a full-width at half-maximum (FWHM) of 0.31° for 600 °C-annealed samples. On annealing, the texturing in films increased along with a decrease in FWHM. AFM micrographs illustrate that the ZnO films are crack-free with well-dispersed homogeneous and uniformly distributed spherical morphology. The synthesized ZnO thin films have transparency >85% in the visible region exhibiting band edge at 375 nm, which becomes sharper with anneal. Room temperature PL spectra of these films show strong ultraviolet (UV) emission around 392 nm with an increase in intensity with annealing temperature, attributed to grain growth. Deconvolution of the PL spectra reveals that there is coupling of free excitons with higher orders of longitudinal optical (LO) phonon replicas leading to a broad asymmetric near-band-edge peak.     

Photoluminescence studies in sol-gel derived Zno films

The photoluminescence (PL) properties of high quality ZnO thin films grown on Si (1 0 0) substrates using spin coating technique are investigated as a function of temperature in the range 10-300 K. The PL spectra shows dominant donor bound excitonic emission along with free exciton related emission in the UV region. The corresponding activation energy of thermal quenching is found to be . The parameters that describe the temperature dependent red shift of the band-edge transition energy are evaluated using different models. The broadening of the PL peak due to increase in temperature is mainly attributed to the exciton-LO phonon coupling.     

Photoluminescence of thermal-annealed nanocolumnar ZnO thin films grown by electrodeposition

Nanostructured zinc oxide thin films formed by partially oriented hexagonal columns with dimensions of about 100 nm × 300 nm have been prepared by cathodic electrodeposition on conducting glass substrates. After subsequent thermal annealing in air at different temperatures (100-500 °C), structural information on the films was obtained by means of non-resonant Raman spectroscopy. Increasing the annealing temperature leads to a higher degree of crystallinity. The photoluminescence activity of the samples (at low temperature) also improves for increasing annealing temperatures in two ways: increasing the intensity of the near-band edge emission and decreasing the width of the excitonic peak. No emission band in the visible is detected, which attests the high quality of the ZnO nanocolumnar films.     

Excitonic polaron and phonon assisted photoluminescence of ZnO nanowires

The coupling strength of the radiative transition of hexagonal ZnO nanowires to the longitudinal optic (LO) phonon polarization field is deduced from temperature dependent photoluminescence spectra. An excitonic polaron formation is discussed to explain why the interaction of free excitons with LO phonons in ZnO nanowires is much stronger than that of bound excitons with LO phonons. The strong exciton-phonon coupling in ZnO nanowires affects not only the Haung-Ray S factor but also the FXA-1LO phonon energy spacing, which can be explained by the excitonic polaron formation.     

Strong ultraviolet emission from zinc oxide thin films prepared by electrophoretic deposition

In this paper, we report a simple and efficient method to prepare high-quality nanocrystalline ZnO films by electrophoretic deposition. Absorption spectrum and transmission electron microscope image indicated that the average size of ZnO nanoparticles is about 9.5 nm. A strong ultraviolet emission peak at 384 nm is observed and the deep-level emission band is barely observed at room temperature. X-ray diffraction pattern revealed that the ZnO film has a polycrystalline hexagonal wurtzite structure. The Raman spectrum showed a typical resonant multi-phonon process within the ZnO film. The frequency shift of 1 LO phonon was about 583 cm⁻¹.     

MBE生长ZnO薄膜的结构和光学特性的研究

用等离子体源辅助分子束外延(P-MBE)方法在蓝宝石(0001)面上生长出了高质量的ZnO薄膜,并对其结构和发光特性进行了研究。在XRD中只观察到ZnO薄膜的(0002)衍射峰,其半高宽(FWHM)值为0.18°;而在共振Raman散射光谱中观测到1LO(579 cm-1 )和2LO(1 152 cm-1 )两个峰位,这些结果表明ZnO薄膜具有单一c轴取向和高质量的纤维锌矿晶体结构。在吸收光谱中观测到自由激子吸收和激子-LO声子吸收峰,这表明在ZnO薄膜中激子稳定的存在于室温,并且两峰之间能量间隔为71.2 meV,与文献上报道的ZnO纵向光学声子能量(71 meV)相符。室温下在光致发光光谱(PL)中仅观测到位于376 nm处的自由激子发光峰,而没有观测到与缺陷相关的深能级发射峰,表明ZnO薄膜具有较高的质量和低的缺陷密度。     

Spectral behavior of the emission around 3.31 eV (A-line) from ZnO nanocrystals

The emission at around 3.31 eV (A-line) from three types of ZnO nanocrystals with different particle sizes (10-1000 nm) was studied. The photoluminescence (PL) measurements were performed under different excitation densities and at different temperatures. The A-line emission exhibited a strong dependence on temperature and excitation power density. With increasing excitation density and temperature overlapping of the closely spaced first longitudinal optical (LO) phonon replica of free excitons by the A-line emission was observed.     

磁控溅射制备ZnO薄膜的受激发射特性的研究

用射频磁控反应溅射法在二氧化硅衬底上制备ZnO薄膜。得到了在不同温度下ZnO薄膜的吸收与光致发光。观测到了纵光学波 (LO)声子吸收峰与自由激子吸收峰 ;室温 (30 0K)下 ,PL谱中仅有自由激子发光峰。这些结果证实了ZnO薄膜具有较高的质量。探讨了变温ZnO薄膜的发光特性。研究了ZnO薄膜的受激发射特性。     

Cesium doped and undoped ZnO nanocrystalline thin films: a comparative study of structural and micro‐Raman investigation of optical phonons

Undoped and cesium‐doped zinc oxide (ZnO) thin films have been deposited on sapphire substrate (0001) using the sol–gel method. Films were preheated at 300 °C for 10 min and annealed at 600 and 800 °C for 1 h. The grown thin films were confirmed to be of wurtzite structure using X‐ray diffraction. Surface morphology of the films was analyzed using scanning electron microscopy. The photoluminescence (PL) spectra of ZnO showed a strong ultraviolet (UV) emission band located at 3.263 eV and a very weak visible emission associated with deep‐level defects. Cesium incorporation induced a blue shift of the optical band gap and quenching of the near‐band‐edge PL for nanocrystalline thin film at room temperatures because of the band‐filling effect of free carriers. A shift of about 10–15 cm⁻¹ is observed for the first‐order longitudinal‐optical (LO) phonon Raman peak of the nanocrystals when compared to the LO phonon peak of bulk ZnO. The UV resonant Raman excitation at RT shows multiphonon LO modes up to fifth order. Copyright © 2010 John Wiley & Sons, Ltd.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Influence of sputter-etching of substrate on the microstructural and optical properties of ZnO films deposited by RF magnetron sputtering

ZnO films were prepared using radio frequency magnetron sputtering on Si(1 1 1) substrates that were sputter-etched for different times ranging from 10 to 30 min. As the sputter-etching time of the substrate increases, both the size of ZnO grains and the root-mean-square (RMS) roughness decrease while the thickness of the ZnO films shows no obvious change. Meanwhile, the crystallinity and c-axis orientation are improved by increasing the sputter-etching time of the substrate. The major peaks at 99 and 438 cm⁻¹ are observed in Raman spectra of all prepared films and are identified as E₂(low) and E₂(high) modes, respectively. The Raman peak at 583 cm⁻¹ appears only in the films whose substrates were sputter-etched for 20 min and is assigned to E₁(LO) mode. Typical ZnO infrared vibration peak located at 410 cm⁻¹ is found in all FTIR spectra and is attributed to E₁(TO) phonon mode. The shoulder at about 382 cm⁻¹ appearing in the films whose substrates were sputter-etched for shorter time (10-20 min) originates from A₁(TO) phonon mode. The results of photoluminescence (PL) spectra reveal that the optical band gap (Eg) of the ZnO films increases from 3.10 eV to 3.23 eV with the increase of the sputter-etching time of the substrate.     

Effect of annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films on sapphire (0 0 0 1) substrates by magnetron sputtering

ZnO thin films were epitaxially grown on sapphire (0 0 0 1) substrates by radio frequency magnetron sputtering. ZnO thin films were then annealed at different temperatures in air and in various atmospheres at 800 °C, respectively. The effect of the annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films are investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL). A strong (0 0 2) diffraction peak of all ZnO thin films shows a polycrystalline hexagonal wurtzite structure and high preferential c-axis orientation. XRD and AFM results reveal that the better structural quality, relatively smaller tensile stress, smooth, uniform of ZnO thin films were obtained when annealed at 800 °C in N₂. Room temperature PL spectrum can be divided into the UV emission and the Visible broad band emission. The UV emission can be attributed to the near band edge emission (NBE) and the Visible broad band emission can be ascribed to the deep level emissions (DLE). By analyzing our experimental results, we recommend that the deep-level emission correspond to oxygen vacancy (V_O) and interstitial oxygen (O_i). The biggest ratio of the PL intensity of UV emission to that of visible emission (I_NBE/I_DLE) is observed from ZnO thin films annealed at 800 °C in N₂. Therefore, we suggest that annealing temperature of 800 °C and annealing atmosphere of N₂ are the most suitable annealing conditions for obtaining high quality ZnO thin films with good luminescence performance.     

Influence of annealing temperature on the photoluminescence property of ZnO thin film covered by TiO2 nanoparticles

In this work, ZnO thin films covered by TiO₂ nanoparticles (labeled as TiO₂-ZnO thin films) were prepared by electron beam evaporation. The influence of annealing temperature on the photoluminescence property of the samples was studied. The structures and surface morphologies of the samples were analyzed by X-ray diffraction (XRD) and atomic force microscope, respectively. The photoluminescence was used to investigate the fluorescent properties of the samples. The measurement results show that the ultraviolet emission of ZnO thin films is largely enhanced after they are covered by TiO₂ nanoparticles, while the green emission is suppressed. However, when the annealing temperature is relatively high (≥500 °C), the intensity of ultraviolet emission drops off and a violet emission peak along with a blue emission peak appears. This is probably connected with the atomic interdiffusion between TiO₂ nanoparticles and ZnO thin film. Therefore, selecting a suitable annealing temperature is a key factor for obtaining the most efficient ultraviolet emission from TiO₂-ZnO thin films.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

ZnO thin films on Si(1 1 1) grown by pulsed laser deposition from metallic Zn target

ZnO thin films with highly c-axis orientation have been fabricated on p-type Si(1 1 1) substrates at 400 °C by pulsed laser deposition (PLD) from a metallic Zn target with oxygen pressures between 0.1 and 0.7 mbar. Experimental results indicate that the films deposited at 0.3 and 0.5 mbar have better crystalline and optical quality and flatter surfaces than the films prepared at other pressures. The full width at half maximum (FWHM) of (0 0 0 2) diffraction peak decreases remarkably from 0.46 to 0.19° with increasing annealing temperature for the film prepared at 0.3 mbar. In photoluminescence (PL) spectra at room temperature, the annealed film at 700 °C exhibits a smaller ultraviolet (UV) peak FWHM of 108 meV than the as-grown film (119 meV). However, an enhanced deep-level emission is observed. Possible origins to above results are discussed.     

Temperature dependent photoluminescence processes in ZnO thin films grown on sapphire by pulsed laser deposition

Temperature dependence of the photoluminescence (PL) transitions in the range of 10–300 K was studied for ZnO thin films grown on sapphire by pulsed laser deposition. The low temperature PL spectra were dominated by recombination of donor bound excitons (B_X) and their phonon replicas. With increasing temperature, free exciton (F_X) PL and the associated LO phonon replicas increased in intensity at the expense of their bound counterparts. The B_X peak with line width of ∼6 meV at 10 K exhibited thermal activation energy of ∼17 meV, consistent with the exciton-defect binding energy. The separation between the F_X and B_X peak positions was found to reduce with increasing temperature, which was attributed to the transformation of B_X into the shallower donor bound exciton complexes at consecutive lower energy states with increasing temperature, which are possible in ZnO. The energy separation between F_X peak and its corresponding 1-LO phonon replica showed stronger dependence on temperature than that of 2-LO phonon replica. However, their bound counterparts did not exhibit this behavior. The observed temperature dependence of the energy separation between the free exciton and it is LO phonon replicas are explained by considering the kinetic energy of free exciton. The observed PL transitions and their temperature dependence are consistent with observations made with bulk ZnO crystals implying high crystalline and optical quality of the grown films.     

A simple growth route towards ZnO thin films and nanorods

Highly orientated ZnO thin films and the self-organized ZnO nanorods can be easily prepared by a simple chemical vapor deposition method using zinc acetate as a source material at the growth temperature of 180 and 320 °C, respectively. The ZnO thin films deposited on Si (100) substrate have good crystallite quality with the thickness of 490 nm after annealing in oxygen at 800 °C. The ZnO nanorods grown along the [0001] direction have average diameter of 40 nm with length up to 700 nm. The growth mechanism for ZnO nanorods can be explained by a vapor-solid (VS) mechanism. Photoluminescence (PL) properties of ZnO thin films and self-organized nanorods were investigated. The luminescence mechanism for green band emission was attributed to oxygen vacancies and the surface states related to oxygen vacancy played a significant role in PL spectra of ZnO nanorods.