多孔硅的制备条件对其光致发光特性的影响

不同的实验条件下制备的多孔硅的光致发光(PL)特性是不同的,这是许多研究产生分歧的主要原因。对比分析了阳极氧化电流密度、阳极氧化时间、溶液浓度以及自然氧化时间对多孔硅光致发光光谱的影响。认为在一定的范围内,多孔硅的发光峰位会随电流密度的增大而蓝移,要获得较强的发光,需要选择合适的电流密度;随着腐蚀时间的延长,多孔硅的发光峰位也发生蓝移。当HF酸的浓度较小时,峰位随浓度的增大表现为向低能移动;而当HF酸的浓度较大时,峰位随浓度的增大则表现为移向高能。多孔硅在空气中自然氧化,其发光峰位发生蓝移,而发射强度随放置时间的延长而降低。并用量子限制模型和发光中心模型对实验结果进行解释。     

多孔硅光致发光的温度效应研究

通过对多孔硅光致发光峰随测量温度变化的研究，发现随测量温度的下降，光致发光峰位有两种截然不同的移动方向：发光峰中心波长较长的样品，主峰向低能方向移动(即红移)；而发光峰位波长较短的样品则向高能方向移动(即蓝移).根据多孔硅光致发光峰的温度效应，定性地给出了发光效率随波长变化的模拟曲线，并由此能较好地解释多孔硅光致发光峰位随温度变化而移动的实验现象. 关键词：     

多孔硅在液体中的两种电致发光光谱

p-型硅片上制作的多孔硅在含有强氧化剂的酸液中处于正向偏压时，可先后产生两种不同的电致发光光谱．一种是红光发射，所需的工作电压极小．随着通电时间增加，红光峰位发生蓝移．这种发光可能与量子尺寸效应有关．另一种是红光猝灭之后出现的白光发射，所需的工作电压很高．由于在酸液中红光猝灭之后，多孔层中形成了一连续的SiO₂薄层，因此在高电场作用下，热电子注入该薄氧化层，从而导致白光发射 关键词：     

发光不衰减的多孔硅

用一种新的方法制备出了具有不同衰减的光致发光特性的多孔硅。如此制备的多孔硅新鲜样品,其发光峰位强度比普通多孔硅高２￣２．５倍,将样品在室温下暴露于空气中,其发光强度在前４个月中单调增加,然后达到饱和。在随后的８个月中,没有观察到发光衰减,发光峰位也没有发生变化,这种发光稳定性被归因子于多孔硅表面所形成的稳定的Ｆｅ－Ｓｉ键。文章探讨了发光不衰减、峰位不蓝移的机理,并为多孔硅发光的量子限域模型提供了强     

提高多孔硅传感特性的一种新方法(英文)

研究了多孔硅(PS)吸附有机溶剂分子后对多孔硅荧光谱的淬灭效应。结果表明:淬灭多孔硅发光的有机溶剂分子是极性分子,有机溶剂分子的极性不同对多孔硅发光的淬灭程度也不同,且有些有机溶剂分子吸附氧化多孔硅比吸附多孔硅引起的发光淬灭具有更好的可逆性和选择性;用含有胺基的正丁胺(CH3CH2CH2CH2-NH2)作碳源,用射频辉光放电等离子系统在多孔硅表面沉积c n膜对多孔硅进行钝化处理后发现:其电致发光强度明显增强,发光峰位兰移,且在大气中存放60天后,其电致发光谱强度基本不衰减,峰位不再移动。经钝化处理的器件较未经处理的器件具有小的串联电阻Rs和低的驱动电压。这为提高多孔硅的传感特性提供了一种新方法。     

掺钛化学腐蚀法制备发光稳定的多孔硅

本文采用掺钛化学腐蚀法制备出了发光稳定性和均匀性都较好的多孔硅 (PS)。存放和退火试验表明 ,光致发光 (PL)谱峰位不蓝移 ,强度不衰减。多孔硅发光稳定性的提高归因于制备过程中样品表面原位氧和钛的钝化。钛的浓度和腐蚀时间对PL强度有明显影响 ,最佳钛浓度约为 0 0 8mol·L- 1 ,最佳腐蚀时间约为 2 0min。掺钛化学腐蚀法制备的PS的光激发过程符合量子限域机制 ,而其PL过程却与量子限域模型不符 ,这表明其光发射过程不是带 带直接跃迁产生的 ,即存在一个表面态     

基于三层模型的多孔硅发光谱双峰结构的研究

基于Litovchenko提出的多孔硅三层模型和在此基础上由Li等人提出的多孔硅三层发光模型,利用半导体异质结理论导出了多孔硅芯部与夹层中载流子浓度、非平衡载流子数目、扩散电流密度、夹层与芯部发光强度的比值等关系式.结果表明:当Egint＞Egcore时,在0.2 eV＜ΔEv+ΔEc＜0.26 eV范围内发光谱将出现双峰,并在ΔEv+ΔEc＞0区域发光峰位不断向高能移动,发生蓝移现象;当Egint＜Egcore时,尽管芯部由于量子限制效应仍将导致发光峰蓝移,但芯部的发光相对夹层的发光相当弱,这时多孔硅发光谱呈现单峰.此模型定量地解释了多孔硅发光峰的蓝移起源于多孔硅量子限制效应,而发光出现发光双峰和发光峰位钉扎是由夹层物质决定,说明了多孔硅的发光存在多种发光机制.     

多孔硅光致发光峰半峰全宽的压缩

硅发光对于在单一硅片上实现光电集成是至关重要的.目前已有的使硅产生发光的方法有:掺杂深能级杂质、掺稀土离子、多孔硅、纳米硅以及Si/SiO₂超晶格.声空化所引发的特殊的物理、化学环境为制备光致发光多孔硅薄膜提供了一条重要的途径.实验表明,声化学处理对于改善多孔硅的微结构,提高发光效率和发光稳定性都是一项非常有效的技术.超声波加强阳极电化学腐蚀制备发光多孔硅薄膜,比目前通用的常规方法制备的样品显示出更优良的性质.这种超声波的化学效应源于声空化,即腐蚀液中气泡的形成、生长和急剧崩溃.在多孔硅的腐蚀过程中,由于超声波的作用增加了孔中氢气泡的逸出比率和塌缩,有利于孔沿垂直方向的腐蚀,使多孔硅光致发光峰的半峰全宽压缩到了3.8nm.     

有机吸附物对多孔硅微腔发光的影响

理论上,采用Bruggeman有效介质近似,研究了有机吸附物对多孔硅微腔的折射率及其光致发光谱的影响.实验上,采用计算机控制的电化学腐蚀法制备了多孔硅微腔样品,并利用机械泵油的蒸气分子与该微腔样品进行相互作用.研究发现,多孔硅微腔发射的窄化光致发光谱对泵油蒸气分子的吸附与脱附很敏感,与之伴随的是该窄化光致发光谱发生明显的峰位移动(可达71nm)和强度变化.结合Bruggeman近似和表面态对多孔硅发光的影响,对实验结果进行了定性解释.实验结果与理论模拟结果符合较好. 关键词： Bruggeman近似 吸附物 多孔硅微腔 光致发光谱     

镶嵌有纳米硅的SiN_x薄膜光致发光的温度依赖特性研究

采用对靶磁控溅射法在单晶硅衬底上沉积镶嵌有纳米硅的氮化硅薄膜,然后在形成气体FG(10%H2,90%N2)气氛中进行450℃常规热退火50min。通过荧光光谱仪测得的稳态/瞬态光致发光(PL)谱研究了镶嵌有纳米硅的氮化硅(SiNx)薄膜样品光致发光特性。结果表明,样品的发光过程可以归因于纳米硅的量子限制效应发光和与缺陷相关的发光。随着激发光能量的增加,PL谱峰位发生蓝移,表明较小粒度的纳米硅发光比例增加;温度的降低会抑制非辐射复合过程,提高辐射复合几率,因此发光寿命延长,发光强度呈指数增加;随着探测波长的减小,样品的发光寿命则明显缩短,表明纳米硅的量子限制效应发光对温度有很强的依赖性。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.