溶胶-凝胶ZrO2-TiO2高折射率光学膜层的抗激光损伤性能研究

采用溶胶-凝胶方法制备了ZrO2-TiO2(Ti含量为0-100 mol%)高折射率光学薄膜.借助激光动态光散射技术研究溶胶微结构.采用傅里叶变换红外光谱、原子力显微镜、薄膜光学常数分析仪、漫反射吸收光谱及强激光辐照实验,对膜层的结构、光学性能及抗激光损伤性能进行了系统表征.结果显示,溶胶-凝胶工艺可以在部分牺牲折射率的情况下,使膜层的抗激光损伤性能得到大幅度提升.随Ti含量从0mol%增加至100 mol%,膜层的平均损伤阈值呈下降趋势,当Ti含量从0mol%增加至60mol%时,平均损伤阈值从57.1 J/cm2下降到21.1 J/cm2(辐照激光波长为1053 nm,脉冲宽度为10 ns,"R/1"测试模式),当Ti含量从60mol%增加至100mol%时,平均损伤阈值变化很小.综合溶胶微结构、膜层光学性能和损伤实验结果可以推断,强激光诱导多光子吸收是引起膜层损伤的主要原因.不同配比的复合膜之间光学带隙的显著差异导致相同辐照激光情况下多光子吸收的概率发生变化,从而导致损伤阈值的规律性变化.     

PVP掺杂-ZrO2溶胶-凝胶工艺制备多层激光高反射膜的研究

以丙醇锆(ZrPr)为锆源，二乙醇胺(DEA)为络合剂，原位引入聚乙烯吡咯烷酮(PVP)，在乙醇体系中成功地合成了PVP掺杂-ZrO₂溶胶.采用旋涂法在K9玻璃基片上制备了PVP-ZrO₂单层杂化薄膜.用不同掺杂量的PVP-ZrO₂高折射率膜层与相同的SiO₂低折射率膜层交替沉积四分之一波堆高反射膜.借助小角X射线散射研究胶体微结构，用红外光谱、原子力显微镜、紫外/可见/近红外透射光谱、椭圆偏振仪以及1064nm的强激光辐照实验对薄膜的结构、光学和抗激光损伤性能进行表征.研究发现，体系组成的适当配置可以在溶胶稳定的前提下实现ZrPr的充分水解，赋予薄膜良好的结构、光学和抗激光损伤性能.杂化体系中，DEA与ZPr之间强的配合作用大大降低了ZrO₂颗粒表面羟基的活性，使得PVP大分子只是以微弱的氢键与颗粒的表面羟基作用而均匀分散于ZrO₂颗粒的周围，对颗粒的形成和生长无显著影响.因而在实验研究范围内，随PVP含量的增大，PVP-ZrO₂杂化膜层的折射率和激光损伤阈值均无显著变化.但是，薄膜中均匀分布的PVP柔性链可以有效促进膜层应力松弛，显著削弱不同膜层之间的应力不匹配程度、大大方便多层光学薄膜的制备.当高折射率膜层中PVP的质量分数达到15%—20%时，膜层之间良好的应力匹配使得多层高反射膜的沉积周期数可达到10以上.沉积10个周期的多层反射膜，在中心波长1064nm处透射率约为1.6%—2.1%，接近全反射特征，其激光损伤阈值为16.4—18.2J/cm²(脉冲宽度为1ns). 关键词： 溶胶-凝胶 2')" href="#">PVP-ZrO₂ 高反射膜 激光损伤     

溶胶-凝胶法制备高折射率TiO2薄膜

 采用溶胶- 凝胶法制备了TiO₂纳米晶溶胶,并以旋涂法（spin-coating）镀制了高折射率光学薄膜。借助光散射技术和透射电镜研究了溶胶的微结构。采用原子力显微镜、场发射扫描电镜、紫外-可见-近红外光谱仪、椭偏仪、漫反射吸收光谱及强激光辐照实验,对膜层的结构、光学性能及抗激光损伤性能进行了系统的表征。结果显示:纳米晶薄膜的折射率达到了1.9,而传统的溶胶-凝胶薄膜折射率只有1.6;同时纳米晶薄膜的抗激光损伤阈值与传统的溶胶-凝胶薄膜相差不大,在1 064 nm处分别为16.3 J/cm²(3 ns脉冲) 和16.6 J/cm²(3 ns脉冲);纳米晶溶胶薄膜可以在保持较高抗激光损伤阈值情况下,大幅度提高薄膜折射率。     

基于透射光谱确定溶胶凝胶ZrO2薄膜的光学常数

基于溶胶凝胶ZrO₂薄膜的紫外/可见/近红外透射实验光谱,采用Swanepoel方法结合Wemple-DiDomenico色散模型,方便地导出了ZrO₂薄膜在200—1200nm波长范围内的光学常数,包括折射率、色散常数、膜层厚度、吸收系数及能量带隙.研究发现,溶胶凝胶ZrO₂薄膜具有高折射率(1.63—1.93,测试波长为632.8nm)、低吸收和直接能量带隙(4.97—5.63eV) 等光学特性,而且其光学常数对薄膜制备过程中的重要工艺 关键词： 光学常数 Swanepoel方法 2薄膜')" href="#">ZrO₂薄膜 热处理     

溶胶凝胶ZrO2/SiO2宽带减反膜的制备与性能

采用溶胶凝胶法制备得到以正丙醇锆和正硅酸乙酯为前驱体的ZrO₂和SiO₂溶胶,通过TFCalc光学薄膜软件模拟了ZrO₂/SiO₂三层“宽M型”基频二倍频减反膜,并使用提拉法制备得到了该均匀膜层。三层减反膜在527 nm和1053 nm处的透过率约为99.5%,且透过率大于99%的波长范围均超过150 nm。经热处理后的膜层表面均方根粗糙度为1.34 nm,表面平整性良好;并运用1-on-1激光损伤阈值测试方法测得该减反膜的零几率激光损伤阈值达到36.8 J·cm^-2(1064 nm,10.7 ns)。     

溶胶-凝胶方法制备ZrO2及聚合物掺杂ZrO2单层光学增反射膜

以丙醇锆(Zr(OPr)₄)为原料，乙酸(HAc)为络合剂，聚乙二醇(PEG200)和聚乙烯吡咯烷酮(PVP)为大分子添加剂，在乙醇体系中成功合成了ZrO₂及聚合物掺杂ZrO₂溶胶.用旋涂法在K9玻璃基片上制备单层光学增反射膜.借助小角X射线散射和激光动态光散射技术研究胶体的微结构.采用傅里叶变换红外光谱、差示扫描量热分析、X射线衍射分析、原子力显微镜、紫外/可见/近红外透射光谱以及椭偏仪对薄膜的结构和光学性能进行表征.用输出波长为1064 关键词： 二氧化锆 溶胶-凝胶 增反射膜 激光损伤     

多重分形谱研究溶胶-凝胶SiO2疏水减反膜的激光预处理作用

采用溶胶-凝胶提拉技术制备了SiO₂疏水减反膜.使用Nd：YAG激光（波长为1064nm,脉宽为7.5ns）采用“R on 1”方式对所得膜层进行了激光预处理.在预处理前后采用“1 on 1”方式考察了薄膜的激光损伤阈值的变化,使用原子力显微镜（AFM）观察了薄膜的表面形貌的变化,并使用多重分形谱（MFS）方法分析了薄膜分形结构的变化.结果表明经过激光预处理后薄膜的抗激光损伤阈值有了明显提高,均方根表面粗糙度（R_q）稍有减小,膜面变平整,多重分形谱宽度收缩,分形区间的分布均匀性改善.这说明经过激光预处理后薄膜表面微结构趋向规整,使之能够承受更强的激光的辐照.同时也说明借助多重分形谱可以获得更多薄膜表面结构变化的信息,多重分形谱是探索强激光对光学薄膜辐照作用机理的一个十分有用的方法. 关键词： 2疏水减反膜')" href="#">SiO₂疏水减反膜 激光预处理 多重分形谱 激光损伤阈值     

常压百级洁净度环境中SiO2薄膜稳定性

在常压百级洁净度环境下,采用三种不同折射率的SiO₂溶胶在熔石英基底上涂制四种不同薄膜,利用光学理论计算模拟了三种胶体涂制的膜层稳定性,通过实验考查了膜层光学指标随时间的变化规律。SiO₂薄膜能够显著提升光学元件透射率,但由于膜层表面的大量羟基及其多孔结构,SiO₂薄膜易吸附周围环境中的有机污染物及水分填充膜层孔隙,从而导致膜层折射率发生变化,影响膜层透射率、反射率等光学性能。实验结果发现,三种溶胶凝胶化学膜在常压百级环境中的有效期为80 d(绝对变化率小于0.1%),且三种胶体涂制的膜层稳定性由高到低依次为折射率1.19, 1.15, 1.25的膜层。     

单层SiO2物理膜与化学膜激光损伤机理的对比研究

采用离子束溅射沉积技术和溶胶-凝胶技术在K9基片上镀制了厚度相近的SiO₂单层介质膜，用表面热透镜技术对两类膜层分别进行了热吸收及实时动态热畸变实验测试，结合散射光阈值测试及实验前后膜层的显微观测，对相同基底、相同膜层材料而采用不同方法镀制的光学膜层，发现化学膜的强激光损伤阈值远高于相应物理膜；从热力学响应及膜层特性差异的角度揭示了化学膜层的强激光损伤阈值远高于相应物理膜层的微观机理，即物理膜具有高吸收下的致密膜层快传导的基底热冲击效应，而化学膜则有低吸收下的疏松空隙填充慢传导的延缓效应，大量的实验数据及现象都证实了这一结论. 关键词： 强激光辐照损伤 损伤形貌 热冲击 热吸收     

ZrO2／SiO2多层膜中膜厚组合周期数及基底材料对残余应力的影响

ZrO₂／SiO₂多层膜由相同沉积条件下的电子束蒸发方法制备而成， 通过改变多层膜中高(ZrO₂)、低(SiO₂)折射率材料膜厚组合周期数的方法，研究了沉积 在熔石英和BK7玻璃 基底上多层膜中残余应力的变化. 用ZYGO光学干涉仪测量了基底镀膜前后曲率半径的变化， 并确定了薄膜中的残余应力. 结果发现，该多层膜中的残余应力为压应力，随着薄膜中膜厚 组合周期数的增加，压应力值逐渐减小. 而且在相同条件下，石英基底上所沉积多层膜中的 压应力值要小于BK7玻璃基底上所沉积多层膜中的压应力值. 用x射线衍射技术测量分析了膜 厚组合周期数不同的ZrO₂／SiO₂多层膜微结构，发现随着周期数增 加，多层膜的结晶程 度增强. 同时多层膜的微结构应变表现出了与所测应力不一致的变化趋势，这主要是由多层 膜中，膜层界面之间复杂的相互作用引起的. 关键词： 2／SiO₂多层膜')" href="#">ZrO₂／SiO₂多层膜 残余应力 膜厚组合周期数     

Preparation of sol-gel ZrO2-SiO2 highly reflective multilayer films and laser-induced damage threshold characteristic

Sol-gel (ZrO₂/SiO₂)¹² ZrO₂ films were prepared by spin coating method. The reflectivity spectrum of the films was measured with a Lambda 900 spectrometer. In order to investigate laser-induced damage threshold (LIDT) characteristic of highly reflective films, one-layer ZrO₂ and SiO₂ films, two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were also prepared by spin coating method. LIDT of each film was measured. Damage morphology after laser irradiation was characterized by optical microscopy (Nikon E600K). The experimental results showed that the reflectivity of (ZrO₂/SiO₂)¹² ZrO₂ film at 1064 nm and 355 nm wavelength is 99.7%. The LIDT results decreases as the number of layer of films increases. All the films have similar damage morphology. The experimental results are explained by the different temperature profiles of the films.     

Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Influence of overcoat on laser-induced damage threshold of 532 and 800 nm TiO2/SiO2 high reflectors

TiO₂/SiO₂ high reflectors with and without a SiO₂ overcoat are deposited by electron-beam evaporation. The film properties are characterized by visible spectrometry measures, structure analysis, roughness and laser-induced damage threshold (LIDT) tests, surface defects and damage morphology observation. The effects of overcoats on LIDT at 532 nm, 8 ns and 800 nm, 220 ps laser pulses are investigated. The relations between film structure, roughness, surface defects, electric field and LIDT are discussed. It is found that overcoats can increase the LIDT at these two laser wavelengths. The reduction of peak temperature, the low defects density and roughness, the low intrinsic absorption of SiO₂ and its amorphous structure are the main reasons for LIDT improvement by overcoats.     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

Investigation of annealing effects on the laser-induced damage threshold of amorphous Ta2O5 films

Ta₂O₅ films were deposited using the conventional electron beam evaporation method and then annealed at temperatures in the range 373-673 K. Chemical composition, scattering and absorption were examined by X-ray photoelectron spectroscopy (XPS), total integrated scattering (TIS) measurement and the surface thermal lensing (STL) technique, respectively. The laser-induced damage threshold (LIDT) was assessed using the output from an Nd:YAG laser with a pulse length of 12 ns. The results showed that the improvement of the LIDT after annealing was due to the reduced substoichiometric and structural defects present in the film. The LIDT increased slightly below 573 K and then increased significantly with increase in annealing temperature, which could be attributed to different dominant defects. Moreover, the root mean square (RMS) roughness and scattering had little effect on the LIDT, while the absorption and the LIDT were in accord with a general relation.     

Influence of SiO2 additional layers on the laser induced damage threshold of Ta2O5 films

A series of Ta₂O₅ films with different SiO₂ additional layers including overcoat, undercoat and interlayer was prepared by electron beam evaporation under the same deposition process. Absorption of samples was measured using the surface thermal lensing (STL) technique. The electric field distributions of the samples were theoretical predicted using thin film design software (TFCalc). The laser induced damage threshold (LIDT) was assessed using an Nd:YAG laser operating at 1064 nm with a pulse length of 12 ns. It was found that SiO₂ additional layers resulted in a slight increase of the absorption, whereas they exerted little influence on the microdefects. The electric field distribution among the samples was unchanged by adding an SiO₂ overcoat and undercoat, yet was changed by adding an interlayer. SiO₂ undercoat. The interlayer improved the LIDT greatly, whereas the SiO₂ overcoat had little effect on the LIDT.     

Influences of CO2 laser annealing on mechanical and laser-induced damage properties of ZrO2 thin films

Zirconium dioxide (ZrO₂) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO₂ laser was used to anneal the ZrO₂ thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO₂ laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO₂ coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO₂ laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO₂ films did not change. The residual stress in ZrO₂ films showed a tendency from tensile to compressive after CO₂ laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters.     

Effects of annealing on laser-induced damage threshold of TiO2/SiO2 high reflectors

The mechanism of improving 1064 nm, 12 ns laser-induced damage threshold (LIDT) of TiO₂/SiO₂ high reflectors (HR) prepared by electronic beam evaporation from 5.1 to 13.1 J/cm² by thermal annealing is discussed. Through optical properties, structure and chemical composition analysis, it is found that the reduced atomic non-stoichiometric defects are the main reason of absorption decrease and LIDT rise after annealing. A remarkable increase of LIDT is found at 300 °C annealing. The refractive index and film inhomogeneity rise, physical thickness decrease, and film stress changes from compress stress to tensile stress due to the structure change during annealing.     

Influence of substoichiometer on the laser-induced damage characters of HfO2 thin films

HfO₂ is one of the most important high refractive index materials for depositing high power optical mirrors. In this research, HfO₂ thin films were prepared by dual-ion beam reactive sputtering method, and the laser-induced damage thresholds (LIDT) of the sample were measured in 1-on-1 mode for laser with 1064 nm wavelength. The results indicate that the LIDT of the as-grown sample is only 3.96 J/cm², but it is increased to 8.98 J/cm² after annealing under temperature of 200 °C in atmosphere. By measuring the laser weak absorption and SIMS of the samples, we deduced that substoichiometer is the main reason for the low LIDT of the as-grown sample, and the experiment results were well explained with the theory of electronic-avalanche ionization.