Structure and microtribological characteristics of laser-arc deposited TiB2 thin film

TiB2 thin film was deposited by laser-arc deposition method on the surface of single crystalline silicon. The morphology, composition, structure and microtribological properties of the film were studied by using XPS, XRD and atomic force/friction force microscope (AFM/FFM). The results show that TiB2 (100) preferred growth on the Si(100) substrate, TiB2(001) preferred growth on the Si(111) substrate. The TiB2 thin film was composed of TiB2 and a small amount of TiO2. The friction coefficient of TiB2 film on substrates Si (100) and Si(111) in microtribological process were 0.087 and 0.073, respectively. TiB2 thin film displayed distinct ability of anti-scratch and wear-resistance.     

The comparison between CdS thin films grown on Si(111) substrate and quartz substrate by femtosecond pulsed laser deposition

Two kinds of cadmium sulfate (CdS) thin films have been grown at 600 °C onto Si(111) and quartz substrates using femtosecond pulsed laser deposition (PLD). The influence of substrates on the structural and optical properties of the CdS thin films grown by femtosecond pulsed laser deposition have been studied. The CdS thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), photoluminescence (PL) and Raman spectroscopy. Although CdS thin films deposited both on Si(111) and quartz substrates were polycrystalline and hexagonal as shown by the XRD , SEM and AFM results, the crystalline quality and optical properties were found to be different. The size of the grains for the CdS thin film grown on Si(111) substrate were observed to be larger than that of the CdS thin film grown on quartz substrate, and there is more microcrystalline perpendicularity of c-axis for the film deposited on the quartz substrate than that for the films deposited on the Si substrate. In addition, in the PL spectra, the excitonic peak is more intense and resolved for CdS film deposited on quartz than that for the CdS film deposited on Si(111) substrate. The LO and TO Raman peaks in the CdS films grown on Si(111) substrate and quartz substrate are different, which is due to higher stress and bigger grain size in the CdS film grown on Si(111) substrate, than that of the CdS film grown on the amorphous quartz substrate. All this suggests that the substrates have a significant effect on the structural and optical properties of thin CdS films. PACS 81.15.Fg; 81.05.Ea; 78.20.-e; 78.67.-n; 42.62.-b     

高择优取向硅基含钾铌酸锶钡（K:SBN）薄膜的制备与性能

采用NbCl5作为先驱物，利用溶胶-凝胶法在Si(100)衬底上成功获得高度择优取向的铁电铌酸锶钡(SBN)薄膜.与用Nb(OC2H5)5作为先驱物的SBN薄膜相比，NbCl5配制的薄膜前驱溶液中含有一定数量的K离子.K离子的含量对SBN薄膜取向的影响存在一个最优值.二次离子质谱测试发现，K离子对SBN晶胞的溶入和对Si衬底的渗透能够同时使SBN晶胞和Si晶胞产生微小扭曲，从而起到调整薄膜与衬底的匹配关系，并最终促使SBN薄膜c轴高度择优取向的生长.测试了薄膜的光学特性. 关键词： 铌酸锶钡 溶胶-凝胶方法 择优取向     

不同晶化工艺对非晶PZT纳米薄膜形核取向生长机理的影响

射频磁控溅射法室温下在Pt/Ti/SiO2/Si上制备非晶Pb(Zr048Ti052)O3薄膜，非晶PZT薄膜分别经常规炉退火(CFA)处理和快速热退火(RTA)处理晶化为（100），（111）不同择优取向的多晶薄膜. 采用x射线衍射测定了薄膜相组分、择优取向度；用原子力显微镜和压电响应力显微镜观察了薄膜表面形貌，以及对应区域由自发极化形成的铁电畴像，观察了不同取向薄膜的电畴分布特征. 结果表明，RTA晶化过程钙钛矿结构PZT结晶主要以PZT/Pt界面处的PtPb化合物为成核点异质形核并类似外延的结晶生长，沿界面结晶速率远大于垂直膜面结晶速率，而CFA晶化样品成核发生在膜内杂质缺陷处，以同质成核为主. 不同的成核机理导致了不同晶面择优取向生长. 关键词： PZT薄膜 结晶 形核 力显微技术     

以MgO为缓冲层的硅基铌酸锶钡薄膜取向特性与其波导结构的设计研究

采用溶胶－凝胶法在Si(100)基片上制备出择优取向的MgO薄膜,随后在其上生长出具有择优取向的铌酸锶钡铁电薄膜.实验发现,MgO缓冲层的应用可以大大提高SBN薄膜的择优取向性能.同时,用五层对称理想波导耦合模理论,以SBN为波导层,分析了波导损耗与厚度的关系. 通过对计算出的理想结果与实际相结合,以及对SBN在生长过程工艺与损耗关系的研究,制备出高质量、低损耗的SBN薄膜,为其在电光波导调制器等微系统中的应用打下良好的基础.     

Microstructural and compositional characteristics of GaN films grown on a ZnO-buffered Si (111) wafer

Polycrystalline GaN thin films have been deposited epitaxially on a ZnO-buffered (111)-oriented Si substrate by molecular beam epitaxy. The microstructural and compositional characteristics of the films were studied by analytical transmission electron microscopy (TEM). A SiO(2) amorphous layer about 3.5 nm in thickness between the Si/ZnO interface has been identified by means of spatially resolved electron energy loss spectroscopy. Cross-sectional and plan-view TEM investigations reveal (GaN/ZnO/SiO(2)/Si) layers exhibiting definite a crystallographic relationship: [111](Si)//[111](ZnO)//[0001](GaN) along the epitaxy direction. GaN films are polycrystalline with nanoscale grains ( approximately 100 nm in size) grown along [0001] direction with about 20 degrees between the (1l00) planes of adjacent grains. A three-dimensional growth mode for the buffer layer and the film is proposed to explain the formation of the as-grown polycrystalline GaN films and the functionality of the buffer layer.     

等离子增强原子层沉积低温生长AlN薄膜

采用等离子增强原子层沉积技术在单晶硅基体上成功制备了AlN晶态薄膜, 利用椭圆偏振仪、原子力显微镜、小角掠射X射线衍射仪、高分辨透射电子显微镜、 X射线光电子能谱仪对样品的生长速率、表面形貌、晶体结构、薄膜成分进行了表征和分析, 结果表明, 采用等离子增强原子层沉积制备AlN晶态薄膜的最低温度为200 ℃, 薄膜表面平整光滑, 具有六方纤锌矿结构与(100)择优取向, Al_2p与N_1S的特征峰分别为74.1 eV与397.0 eV, 薄膜中Al元素与N元素以Al-N键相结合, 且成分均匀性良好. 关键词： 氮化铝 等离子增强原子层沉积 低温生长 晶态薄膜     

Study on the orientation of silver films by ion-beam assisted deposition

Low energy ion beam assisted deposition (IBAD) was employed to prepare Ag films on Mo/Si (100) substrate. It was found that Ag films deposited by sputtering method without ion beam bombardment were preferred (111) orientation. When the depositing film was simultaneously bombardment by Ar⁺ beam perpendicular to the film surface at ion/atom arrival ratio of 0.18, the prepared films exhibited weak (111) and (200) mixed orientations. When the direction of Ar⁺ beam was off-normal direction of the film surface, Ag films showed highly preferred (111) orientation. Monte Carlo method was used to calculate the sputtering yields of Ar⁺ ions at various incident and azimuth angles. The effects of channeling and surface free energy on the crystallographic orientation of Ag films were discussed.     

湿法刻蚀对Si基片孔点阵及ZnO外延薄膜周期形貌的影响

利用射频等离子体辅助分子束外延法,在刻有周期性孔点阵结构的Si衬底上生长了ZnO二维周期结构薄膜,系统研究了湿法化学刻蚀对孔形点阵Si(100),Si(111)基片表面形貌的影响,以及两种初底上ZnO外延薄膜的结晶质量与周期形貌的差异.X射线衍射及扫描电子显微测试结果表明：Si (111)衬底上生长出的ZnO二维周期结构薄膜具有较好的结晶质量与较好的周期性表面形貌.该研究结果为二维周期结构的制备提供了一种新颖的方法. 关键词： ZnO 分子束外延 Si 湿法刻蚀     

不同衬底上Pb(Zr0.52Ti0.48)O3择优取向铁电薄膜的制备和研究

通过MOD法在Si(100)和Pt(111)/Ti/SiO₂/Si基片上制备出LaNiO₃ ( LNO)薄膜.再通过修 正的Sol-gel法，在Pt(111)/Ti/SiO₂/Si,LNO/Si(100)和LNO/Pt/Ti/SiO_{2< /sub>/Si三种衬底上 制备出具有择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜. 经XRD分析表明，L NO薄膜具有(100)择优取向的类钙钛矿结构；PZT薄膜均具有钙钛矿结构，且在Pt(111)/Ti/S iO2/Si衬底上的薄膜以(110)择优取向，在LNO/Pt/Ti/SiO2/Si和LN O/Si(100)衬底上的 薄膜以(100)择优取向.经场发射SEM分析和介电、铁电性能测试表明，在LNO/Si和LNO/Pt/Ti /SiO2/Si衬底上的PZT薄膜的平均粒径、介电常数以及剩余极化强度均比以Pt/T i/SiO2/Si为衬底的薄膜大. 关键词： 3}薄膜')" href="#">LaNiO₃薄膜 PZT铁电薄膜 择优取向 剩余极化强度     

Pd-Si薄膜固相反应的透射电子显微镜研究

本工作利用透射电子显微术研究了Pd-Si薄膜固相反应的初始生成相及生成相Pd₂Si与(111)取向Si衬底的取向关系随Pd膜厚度、退火温度等因素的变化规律。实验结果表明:在衬底保持室温的条件下,Pd沉积到Si(111)上时也能够生成一层外延的Pd₂Si,其厚度足以在常规的选区电子衍射中产生明显的信号。在170℃退火时,Pd-Si反应即可持续到生成200nm厚的外延的Pd₂Si。在Pd膜厚度为400nm的条件下,Pd₂Si与Si(111)衬底的取向关系为[0001]_(Pd2Si)轴织构。 关键词：     

TiN growth on Si by hybrid radical beam PLD

High-quality (good crystallinity and stoichiometry) titanium nitride (TiN) thin films were grown on Si(100) substrates by pulsed laser deposition (PLD) using a high-purity titanium target (99.99%) and nitrogen radical beam. The crystallinity, chemical composition, and depth profiles of the grown films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Rutherford backscattering spectroscopy (RBS), respectively. The XRD pattern indicated that the preferred growth of TiN(200) with an orientation parallel to the Si(100) direction was obtained and the nitrogen radical drastically improved crystallinity compared with that grown in ambient nitrogen gas. RBS spectra indicated that the combination of PLD and the nitrogen radical beam suppressed silicidation at the interface between the Si substrate and TiN thin film during growth. The XPS analysis revealed that this method achieved the synthesis of stoichiometric TiN films.     

Effects of deposition temperature and thickness on the structural properties of thermal evaporated bismuth thin films

Bismuth (Bi) thin films of different thicknesses were deposited onto Si(1 0 0) substrate at various substrate temperatures by thermal evaporation technique. Influences of thickness and deposition temperature on the film morphologies, microstructure, and topographies were investigated. A columnar growth of hexahedron-like grains with bimodal particle size distribution was observed at high deposition temperature. The columnar growth and the presence of large grains induce the Bi films to have large surface roughness as evidenced by atomic force microscopy (AFM). The dependence of the crystalline orientation on the substrate temperature was analyzed by X-ray diffraction (XRD), which shows that the Bi films have completely randomly oriented polycrystalline structure with a rhombohedral phase at high deposition temperature (200 °C) and were strongly textured with preferred orientation at low deposition temperatures (30 and 100 °C).     

Si(100)表面Se薄膜生长及其在Ti/Si欧姆接触中的应用

本文采用分子束外延(MBE)系统在Si(100)表面淀积Se薄膜. 通过控制衬底和固态Se束源炉的温度,实现了Se材料在Si(100)表面上的自限制超薄薄膜生长;在Se超薄层钝化的Si(100)表面上制备的Ti金属电极具有低的欧姆接触电阻特性,且热稳定性温度提升至400 ℃. 关键词： 硒 钝化 欧姆接触 热稳定性     

IR and SFM study of PTCDA thin films on different substrates

FT-IR spectroscopy and SFM were used to investigate the growth of thin films of the organic semiconductor 3,4,9,10-perylenetetracarboxylicdianhydride (PTCDA) deposited by vacuum sublimation onto various substrates, i.e. Ag(111) layers on mica, KBr(100), mica, oxidized Si, and TiO₂ nanoparticles on Si. Layer thicknesses of PTCDA varied from 10 to 1500 nm.The anhydride vibrations of PTCDA differ for the used substrates, which can be connected to the orientation of the molecules relative to the substrate surface and the film morphology as detected in the SFM pictures.     

Molecular dynamic simulations of surface morphology and pulsed laser deposition growth of lithium niobate thin films on silicon substrate

The molecular dynamic simulation of lithium niobate thin films deposited on silicon substrate is carried out by using the dissipative particle dynamics method. The simulation results show that the Si(111) surface is more suitable for the growth of smooth Li Nb O3 thin films compared to the Si(100) surface, and the optimal deposition temperature is around873 K, which is consistent with the atomic force microscope results. In addition, the calculation molecular number is increased to take the electron spins and other molecular details into account.     

Growth of orientation-controlled Pb(Mg,Nb)O3-PbTiO3 thin films on Si(100) by using oriented MgO films as buffers

Thin films of relaxor ferroelectric Pb(Mg,Nb)O₃-PbTiO₃ with different orientations were grown by pulsed-laser deposition on Si(100). By using (111)-, (110)- and (100)-oriented MgO thin film as buffer and the LaNiO₃ thin film as a bottom electrode, (110)- and (100)- oriented or preferred and polycrystalline PMN-PT thin films were obtained. The (110)-oriented PMN-PT thin film showed dielectric permittivity of about 1350 and loss factor cosδ of <0.07. PACS 68.55.Jk; 81.15.Fg; 77.84.Dy     

Synthesis of epitaxial Si(100) nanowires on Si(100) substrate using vapor–liquid–solid growth in anodic aluminum oxide nanopore arrays

The synthesis of epitaxial Si nanowires with growth direction parallel to Si [100] on Si(100) substrate was demonstrated using a combination of anodic aluminum oxide (AAO) template, catalytic gold film sandwiched between the template and the Si(100) substrate and vapor-liquid-solid growth using SiH₄ as the Si source. After growing out from the AAO nanopores, most Si nanowires changed their diameter and growth direction into larger diameter and 〈111〉 direction. PACS 81.07.-b; 82.45.Cc     

TiN薄膜在纳米压痕和纳米划痕下的断裂行为

利用磁控溅射方法在Si(111)衬底上制备了具有(111)和(222)择优取向的TiN薄膜. 用纳米压痕和纳米划痕方法研究了该薄膜的变形和断裂行为. 用扫描电子显微镜、纳米压痕原位原子力显微镜及原位光学显微镜并结合加-卸载 曲线及划痕曲线获得了薄膜发生变形和断裂的微观信息. 在压痕试验中, TiN薄膜在压入深度为200 nm时表现为塑性变形及压痕周围的局部断裂, 随着压入深度的增大, 塑性变形和局部断裂变得越显著, 当最大压入深度达到临界值1000 nm时, 薄膜和衬底间发生了界面断裂. 在划痕实验中, 100 mN及200 mN的最大载荷均可以引起界面断裂. 最大为200 mN的载荷使得薄膜发生界面断裂的位置比用100 mN载荷时的位置提前, 但其临界断裂载荷和100 mN时及压痕实验时的临界界面断裂载荷基本相同. 关键词： TiN薄膜 纳米压痕 纳米划痕 界面断裂     

衬底温度对PLD制备的Mo薄膜结构及表面形貌的影响

 运用脉冲激光沉积(PLD)技术在Si(100)基片上沉积了金属Mo薄膜。在激光重复频率2 Hz,能量密度5.2 J/cm²,本底真空10^－6 Pa的条件下,研究Mo薄膜的结构和表面形貌,讨论了衬底温度对薄膜形貌与结构的影响。原子力显微镜(AFM)图像和X射线小角衍射(XRD)分析表明,薄膜表面平整、光滑,均方根粗糙度小于2 nm。沉积温度对Mo薄膜结构和表面形貌影响较大,在373~573 K范围内随着温度升高,薄膜粗糙度变小,结晶程度变好。