流变学法研究部分水解聚丙烯酰胺/Cr(III)交联反应I.浓度的影响

采用流变学法系统地考察了部分水解聚丙烯酰胺（HPAM）/Cr(III)交联体系的 反应动力学。HPAM溶液的粘性模量G”大于弹性模量G’,且其数值随时间不发生变 化,体系为粘性溶液。而HPAM/Cr(III)体系的G’和G”的数值都随时间变化,G” 在反应开始阶段大于G’,当反应进行一段时间后,G’超过G”占据主要地位,体 系成为弹性体系。交联过程可分为三个阶段：第一上升阶段,平缓上升阶段和第二 上升阶段。利用G’～ t曲线可以推测反应机理。实验发现成胶速率随反应物HPAM 和Cr(III)的浓度的增加而增加,而成胶时间缩短。在羧基浓度过量的情况下,交 联反应对Cr(III)浓度的反应级数是1。凝胶的有效弹性交联密度随聚合物浓度的增 加而增,且随凝胶反应的进行而增加。凝胶的交联点间的平均分子量随Cr(III)浓 度的增加和交联反应的进行而下降。     

流变学法研究部分水解聚丙烯酰胺/Cr(Ⅲ)交联反应Ⅰ.浓度的影响

采用流变学法系统地考察了部分水解聚丙烯酰胺(HPAM)/Cr(Ⅲ)交联体系的反应动力学.HPAM溶液的粘性模量G"大于弹性模量G＇,且其数值随时间不发生变化,体系为粘性溶液.而HPAM/Cr(Ⅲ)体系的G＇和G"的数值都随时间变化,G"在反应开始阶段大于G＇,当反应进行一段时间后,G＇超过G"占据主要地位,体系成为弹性体系.交联过程可分为三个阶段:第一上升阶段,平缓上升阶段和第二上升阶段.利用G＇～t曲线可以推测反应机理.实验发现成胶速率随反应物HPAM和Cr(Ⅲ)的浓度的增加而增加,而成胶时间缩短.在羧基浓度过量的情况下,交联反应对Cr(Ⅲ)浓度的反应级数是1.凝胶的有效弹性交联密度随聚合物浓度的增加而增加,且随凝胶反应的进行而增加.凝胶的交联点间的链平均分子量随Cr(Ⅲ)浓度的增加和交联反应的进行而下降.     

部分水解聚丙烯酰胺柠檬酸铝体系临界交联浓度的研究

采用落球粘度计、核孔膜过滤、动态光散射 (DLS)和2 7Al NMR法 ,研究了高分子量、低浓度的部分水解聚丙烯酰胺 (HPAM)与柠檬酸铝 (AlCit)体系形成交联聚合物溶液 (LPS)的临界交联浓度 .研究结果表明 ,HPAM AlCit体系在聚合物浓度较低时 ,溶液中主要发生形成交联聚合物线团 (LPC)的交联反应 ,此时形成的是LPS ,聚合物浓度增加到某一临界值后 ,体系中形成线团后 ,存在线团间的交联 ,此时形成的是弱凝胶 .不同方法所测得的HPAM AlCit体系的临界交联浓度基本相同 ,对于粘均相对分子质量为 1 4× 10 7的HPAM ,在NaCl浓度为 2 0 0 0mg L ,交联比 2 0∶1时形成的交联体系 ,其临界交联浓度在 2 0 0～ 30 0mg L间 .     

水解聚丙烯酰胺柠檬酸铝体系成胶行为与形态结构的研究

采用光学显微镜、扫描电镜及流变性能测试等手段 ,研究了部分水解聚丙烯酰胺 (HPAM )与柠檬酸铝 (AlCA)的成胶行为与形态结构 .结果表明 ,当AlCA浓度超过 10 0mg/L时 ,随HPAM浓度由低向高变化 ,HPAM AlCA交联体系可形成三种不同形态结构的凝胶 :分散凝胶 (由交联聚合物颗粒形成的分散体 )、两相(分散凝胶相与连续网状凝胶相 )共存凝胶和连续网状凝胶 .HPAM AlCA形成分散凝胶时 ,无明显的粘度升高现象 ,但体系中存在由HPAM大分子交联在一起的颗粒结构 .HPAM AlCA在形成连续网状凝胶时 ,体系复模量和复粘度大幅度提高 ,网状凝胶中含有粒状凝胶颗粒 .     

原子吸收法研究部分水解聚丙烯酰胺/Cr(Ⅲ)凝胶的交联密度

由 Cr( )交联部分水解聚丙烯酰胺 ( HPAM)形成的水凝胶已广泛应用于油田三次采油生产中 ,对于调整吸水剖面和提高原油采收率起到重要作用 .在 HPAM/Cr( )交联机理和交联动力学等方面的研究多采用粘度法 [1] 、紫外 -可见分光光度法 [2 ] 、流变学法[3] 、原子力显微镜 ( AFM)法 [4 ] 、粒度及其分布法 [5] 等 ,考察 HPAM/Cr( )交联反应过程 ,而对交联密度ρ的研究却少见报道 .ρ可用单位体积凝胶中参与交联反应的 Cr( )的量 ( g/cm3)来表征 ,在微观上反映了交联点的数目 ,在宏观上与凝胶的强度和脱水程度相联系 ,因而是交联体系…     

低浓度部分水解聚丙烯酰胺/柠檬酸铝交联体系剪切稳定性研究

采用粘度法、核孔膜过滤和动态光散射(DLS)法,研究了高分子量低浓度的部分水解聚丙烯酰胺(HPAM)与柠檬酸铝(AlCit)反应所形成的交联体系的剪切稳定性和HPAM剪切降解后与AlCit反应所形成的体系的封堵性能及降解机理.研究结果表明,低浓度的HPAM与AlCit反应所形成的交联聚合物体系随剪切速率增加,其对1.2μm的核孔膜的封堵能力降低.HPAM稀溶液剪切降解后再与AlCit反应,低剪切速率对其封堵性能影响较小,而高剪切速率会使得其封堵性能大大降低.HPAM/AlCit交联体系和HPAM剪切降解后形成的交联体系的封堵性能下降的原因是HPAM/AlCit交联体系中交联聚合物线团(LPC)尺寸和HPAM中高分子线团的尺寸变小.     

柠檬酸铝/聚丙烯酰胺胶态分散凝胶反应动力学和机理的研究

采用粘度法研究了柠檬酸铝（AlCit)与部分水解取丙烯酰胺（HPAM）胶态分散凝胶体系的反应动力学。结果表明，胶态分散凝胶体系的交联反应是一级反应。并推导出胶态分散凝胶体系的反应动力学方程。     

低浓度HPAM/AlCit交联体系的27Al NMR研究

用27Al NMR谱研究了高分子量低浓度的部分水解聚丙烯酰胺(HPAM)与柠檬酸铝(AlCit)体系交联反应过程中Al的化学位移和Al的自旋-晶格弛豫时间的变化. 结果表明, HPAM与AlCit反应后, 与HPAM分子链上的羧基发生配位交联的Al的化学位移向低场移动, 而不参与交联反应的AlCit分子结构中Al的化学位移基本不变. HPAM/AlCit交联体系中存在三种形态的Al, 分别对应三种不同的自旋-晶格弛豫时间. 当HPAM的质量浓度≤200 mg/L时, HPAM与AlCit反应过程中交联态Al的自旋-晶格弛豫时间τ13随反应进行变小, HPAM与AlCit主要发生分子内交联反应. 当HPAM的质量浓度≥250 mg/L时, HPAM与AlCit反应过程中交联态Al的自旋-晶格弛豫时间τ13随反应进行变大, HPAM与AlCit主要发生分子间交联反应.     

粘度法研究胶态分散凝胶交联过程

通过粘度测定方法,研究了部分水解聚丙烯酰胺（ＨＰＡＭ）／ 柠檬酸铝（ＡｌＣｉｔ） 交联过程中粘度变化的特性．聚合物浓度高的ＨＰＡＭ／ＡｌＣｉｔ 体系粘度随反应时间的延长而上升,其体系粘度最终高于相同聚合物浓度的ＨＰＡＭ 溶液粘度．聚合物浓度低的ＨＰＡＭ／ＡｌＣｉｔ 体系粘度随反应时间的延长而下降,其体系粘度低于相同聚合物浓度的ＨＰＡＭ 溶液粘度．ＨＰＡＭ／ＡｌＣｉｔ 交联体系的聚合物浓度低于临界浓度时,交联反应后形成稀胶态分散凝胶（ＴＣＤＧ） ．在实验条件下,临界浓度在１５０ ～３００ｍｇ／Ｌ 之间．当聚合物浓度于临界浓度和７００ｍｇ／Ｌ之间时,形成浓胶态分散凝胶（ＣＣＤＧ） ;当聚合物浓度高于７００ｍｇ／Ｌ 时,ＨＰＡＭ／ＡｌＣｉｔ 交联体系形成整体凝胶．     

部分水解聚丙烯酰胺弱凝胶交联动力学的流变学分析

用流变学方法对部分水解聚丙烯酰胺(HPAM)苯酚甲醛间苯二酚交联体系的弱凝胶化过程进行了研究,通过对基团转化率和高分子交联转化率的分析,发现凝胶化过程在接近凝胶点时,处于反应动力学的初期,这使得交联点增加的动力学是比较简单的.通过在不同聚合物浓度和交联剂浓度并在地层温度和矿化度条件下线性粘弹性行为的研究,得到了交联体系凝胶化动力学过程的完整数据,发现聚合物浓度与交联剂浓度对凝胶点与凝胶强度的影响比较类似,反映出交联点增加的共同动力学特征.复数粘度在一个诱导期后,是以指数上升的,类似一个一级反应的特征.产生交联的临界聚合物浓度约为250mg L左右.并提出了剪切粘度数学模型,可以描述凝胶化过程中流变性质的变化.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

解决能源问题的新途径--光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。