电化学预处理微纤维电极用于毛细管电泳安培检测局部麻醉药

本文研究了电化学预处理碳纤维的各种条件，如处理电压、处理时间、处理后稳定时间、溶液条件等对局部麻醉药普鲁卡因、利多卡因电化学行为的影响。找出的电化学预处理最佳条件是在２．０Ｖ进行１．５ｍｉｎ阳极化处理并在缓冲液中保持１０ｍｉｎ。     

电-多相催化反应器强化处理苯胺废水的研究

本文设计一种新型的电-多相催化反应器处理苯胺废水.考察外加电压,电解时间,初始pH值以及支持电解质浓度等工艺条件对电解效果的影响.实验表明,在外加电压30 V、电解时间l h、初始pH=7和支持电解质Na2SO4溶液浓度为800 mg/L的条件下,该反应器对苯胺有最佳的处理效果,优于单独电化学处理体系.     

甲基苯丙胺电化学检测条件的优化

采用电化学方法检测甲基苯丙胺,探讨了不同扫描速度、初始浓度、pH值、电极处理温度及干扰物对检测的影响,获得了甲基苯丙胺电化学检测的最佳条件.结果表明,工作电极为掺硼金刚石薄膜电极,扫描速度为50~100 m V/s,初始浓度小于100 mg/L,pH=7.0及电极处理温度为100℃时,甲基苯丙胺的检测速度最快,检测结果最好,同时干扰物对于电化学方法检测甲基苯丙胺无明显影响.     

毛细管电泳-联吡啶钌电化学发光法对血浆中丁卡因与普鲁卡因的同时测定

建立了毛细管电泳-电致化学发光同时测定丁卡因和普鲁卡因的新方法.考察了毛细管电泳流动相和检测池中磷酸盐缓冲液pH和浓度、进样时间和电压、分离电压和检测电位等对丁卡因和普鲁卡因的分离以及联吡啶钌电致化学发光检测的影响.基于循环伏安法考察了丁卡因和普鲁卡因的电化学行为与发光机理.在优化的实验条件下,丁卡因和普鲁卡因的标准曲线分别在6.6 ～265.6 μmol/L和0.7 ～219.0 μmol/L范围内呈良好的线性,检出限(S/N=3)分别为1.9 μmol/L和0.2 μmol/L.对23 μmol/L丁卡因和15 μmol/L普鲁卡因的标准溶液连续测定5次,迁移时间的相对标准偏差(RSD)分别为0.13%、0.16%,电化学法发光强度的RSD分别为3.7%和4.9%.该方法已成功用于血浆中丁卡因和普鲁卡因的同时检测,平均回收率均为94%,相对标准偏差低于4%.     

电化学氧化和臭氧化预处理酸性化工废水的效能研究

保持一定酸度条件下对比了电化学氧化和臭氧氧化预处理酸性化工废水的效能（废水原pH 0.85）. 结果表明,在废水中添加2 g·L^-1 NaCl电化学氧化预处理效果较佳,30 mA·cm^-2条件下电解20 min后水样的CODCr（化学需氧量）去除率达43.4%,BOD₅/COD_Cr（生化需氧量与化学需氧量的比值）值从原来的0.034上升至0.14,可生化性明显提高. 单独臭氧化仅在pH 7.0才能取得一定的预处理效能. Ti(Ⅳ)/O₃/H₂O₂高级氧化体系在pH 2.85条件下亦有较好的预处理效果,16 min后水样COD_Cr去除率达22.9%,BOD₅/COD_Cr值则提高至0.072.     

芬顿体系降解邻苯二酚和对苯二酚研究

基于石墨烯修饰电极,分别建立了对苯二酚(HQ)和邻苯二酚(CC)浓度与电化学信号的工作曲线,并通过差分脉冲伏安法(DPV)考察了Fe~(2+)与H_2O_2添加量、pH环境及降解时间对HQ、CC降解率影响。结果表明:Fe~(2+)/H_2O_2芬顿体系对HQ、CC的降解效果明显,其中羟基自由基起主导作用。处理50 mL 6×10~(-5) mol·L~(-1)的苯二酚污染物时,Fe~(2+)与H_2O_2摩尔比为5∶4,芬顿试剂添加量为9.8×10~(-5) mol,降解时间为45 min,分别在pH=4.0的条件下降解HQ和pH=5.0的条件下降解CC,降解率分别达88.8%(HQ)和96.1%(CC)。     

毛细管电泳-间接电化学发光法对茶叶中百草枯农药残留的检测

基于农药百草枯对钌联吡啶-三丙胺(TPA)体系的电化学发光具有显著的抑制作用,建立了毛细管电泳-间接电化学发光检测茶叶中残留农药百草枯的新方法.讨论了初始电位、钌联吡啶和TPA浓度、进样电压、进样时间、运行缓冲溶液的浓度与pH值等条件对百草枯检测灵敏度的影响.确定最佳实验条件为1.20 V初始电压、0.7 mmol/L钌联吡啶、0.6 mmol/L TPA、9 kV进样电压、9 s进样时间、35 mmol/L磷酸盐(pH 8.5)为运行缓冲溶液.在优化实验条件下,百草枯浓度在5×10~(-7) 5×10~(-5)mol/L范围内呈良好线性(相关系数为0.994 5),检出限为9.4×10~(-8) mol/L.对5×10~(-5) mol/L百草枯标准溶液连续测定5次,相对峰高与迁移时间的相对标准偏差分别为3.7%和2.1%.该方法对2.0×10~(-6)、1.0×10~(-5) mol/L百草枯标样的萃取回收率分别为74%和83%,相对标准偏差分别为15%、4.2%(n=5).     

蛋氨酸硒络合反应条件的响应曲面法优化

以蛋氨酸和亚硒酸钠为原料合成了蛋氨酸硒;采用基于3因素5水平的中心组合设计实验的响应曲面法,分析了温度(30℃~80℃)、酸度(pH 4~9)、时间以及它们之间的交互作用对蛋氨酸硒产率的影响,确定了合成蛋氨酸硒的最佳工艺条件.通过典型分析确定优化的络合反应条件为:温度50℃,pH 6.93,时间90 min;相应的蛋氨酸硒的产率为51.58%.相关研究结果表明,采用响应曲面法优化确定的蛋氨酸硒合成工艺合理有效、切实可行.     

液相微萃取-气相色谱/质谱测定水中硝基苯类化合物

建立了水中硝基苯类化合物(硝基苯、1-硝基甲苯、2-硝基甲苯、3-硝基甲苯和邻氯硝基苯)的液相微萃取-气相色谱/质谱检测方法。实验结果显示:甲苯为最佳的萃取剂。确定最佳实验条件为:甲苯体积2μL,萃取时间15 min,搅拌速度300 r/min,萃取温度45℃,溶液pH=5。在此条件下,各目标物的萃取富集倍数为30~38,线性范围为2~250μg/L,检出限为1~2μg/L,测定的相对标准偏差为5%~7%。     

芯片毛细管电泳电化学发光法快速测定盐酸普鲁卡因的含量

建立了芯片毛细管电泳电化学发光法快速测定盐酸普鲁卡因含量的新方法。采用三联吡啶钌(Ru(bpy)2+3)为电化学发光试剂,三电极体系(直径300μm的铂圆盘电极为工作电极,集成在铂圆盘工作电极外的钛管为对电极,Ag/AgCl丝为参比电极)进行检测。分别考察了运行缓冲溶液pH值、检测缓冲溶液pH值、检测电位以及分离电压对分离和检测性能的影响。在优化条件下,即运行缓冲溶液为10mmol/L磷酸盐溶液(pH4.0),检测池缓冲溶液为含5mmol/LRu(bpy)2+3的50mmol/L磷酸盐缓冲溶液(pH7.0),检测电位为1.25V,分离电压为300V/cm时,盐酸普鲁卡因可在40s内实现较好的分离与检测,其线性范围为10~2000μg/mL(r2=0.9991),检出限(S/N=3)为3.0μg/mL,加标回收率为97%~99%,相对标准偏差为1.8%~2.2%。该方法简便、快速、准确,可用于盐酸普鲁卡因注射液的质量控制。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。