沉淀剂对AU/ZnO催化剂CO氧化性能及催化剂结构的影响

在25 C和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性.结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO氧化性能.由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3种沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1 100 h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂.在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相.催化剂的稳定性与金粒子长大速度和碳酸根累积量有关.     

沉淀剂对Au／ZnO催化剂上CO氧化性能及催化剂结构的影响

在25℃和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性。结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO拉化性能。由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1100h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂。在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相。催化剂的稳定性与金粒子长大速度和碳酸根累积量有关。     

沉淀剂种类对水煤气变换Au/Fe2O3催化剂结构和催化性能的影响

 采用7种沉淀剂(K2CO3, Na2CO3, NH4OH, (NH4)2CO3, NaOH, KOH和尿素)通过共沉淀法制备了低温水煤气变换(WGS) Au/Fe2O3催化剂,考察了沉淀剂种类对其催化性能的影响. 通过N2吸附, X射线荧光光谱、 X射线衍射、 H2程序升温还原和CO程序升温脱附等表征手段,探讨了不同沉淀剂影响Au/Fe2O3催化剂WGS性能的原因. 结果表明,采用K2CO3和Na2CO3制备的催化剂样品在200 ℃以上具有较好的活性和稳定性,其中K2CO3是最佳沉淀剂. 而采用NH4OH和(NH4)2CO3制备的样品的催化活性相对较低,在200 ℃达到峰值. 由其它3种沉淀剂制备的样品的催化活性都较差, CO转化率最高只有35%. 沉淀剂种类不仅明显地影响金离子和铁离子的共沉淀,而且会明显地影响共沉淀物在后续焙烧过程中的结晶行为. 前者将影响金的负载量,后者则影响金粒子的分散度以及氧化铁载体的还原性质和对CO的吸脱附性能. Au/Fe2O3催化剂的低温高活性及其稳定性归因于高度分散的金粒子及其与易被还原的氧化铁载体间的协同作用. 催化剂中金负载量增大、金粒子分散度提高以及氧化铁晶粒减小均有利于其催化性能的提高.     

大学无机化学实验中碱式碳酸铜制备方法探讨

探讨大学无机化学实验中有关碱式碳酸铜制备的实验方法,并以Cu(NO3)2为原料、NaOH和Na2CO3的混合液为沉淀剂制备碱式碳酸铜。讨论反应物最佳配比、pH、温度等因素对产品的影响,并对所制产品进行XRD分析,提出一种制备碱式碳酸铜的大学无机化学实验方法。     

不同沉淀剂对Co3O4催化剂催化分解N2O活性的影响

采用了不同沉淀剂（K2 CO3、Na2 CO3、NaOH、NaHCO3）制备了一系列 Co3 O4氧化物催化剂。通过 XRD、XPS、BET、H2-TPR、O2-TPD 表征手段,探究了催化剂物相结构和氧化还原性能对 N2 O 催化分解性能的影响。研究表明,以 K2 CO3为沉淀剂制备的 Co3 O4催化剂具有优越的氧化还原性能。此外,较低结晶度有助于提高催化剂的催化性能,催化剂表面物种与其沉淀剂相关：丰富的表面 Co 物种促进催化活性,较多氧空位有利于催化剂表面的电子传递和氧气的脱附。以 K2 CO3为沉淀剂制备的 Co3 O4催化剂表现出最佳的 N2 O 催化分解活性,在450℃达到90％以上的转化率。     

纳米CuO/Bi2O3粉体的制备及催化性能

以Cu(NO3)2,Bi(NO3)3和CO(NH2)2为原料,用水解法并掺加添加剂直接制备出纳米CuO／Bi203粉体。用FI-IR,XRD和TEM对其组成、粒子大小、表面形貌进行表征。结果表明,CuO／Bi：0,为类球形纳米粉体,粒度均匀,粒径20nm～4nm。实验结果证明CuO／Bi2O3对合成丁炔二醇具有良好的催化活性和选择性。     

NH4+交换度对 CuY催化剂上甲醇氧化羰基化反应性能的影响

碳酸二甲酯(DMC)是一种应用极其广泛的绿色化工产品,其中经济、绿色的甲醇氧化羰基化合成 DMC工艺极具工业前景,而 Y分子筛负载铜(CuY)是有效催化剂之一.众所周知, CuY催化剂上的 Cu+是催化活性中心. Cu+催化活性中心的引入方式用两种：(1) CuCl直接与 HY分子筛固相离子交换;(2) Cu2+与 NaY分子筛溶液离子交换,然后 Cu2+自还原生成活性中心 Cu+.在无溶剂条件下制备 CuY催化剂时,载体 HY分子筛中的可交换位 H+量是决定催化剂 CuY氧化羰基化催化性能的关键因素.文献通过以不同硅铝比的 HY分子筛为载体制备的催化剂 CuY,研究铜离子可交换位 H+量对氧化羰基化的影响,然而,硅铝比的不同也直接影响了分子筛骨架的组成、Si–O–Al的键角、甚至影响了 Al3+的分散度,这些因素都直接影响了 CuY催化剂活性.因此,研究 NaNH4Y分子筛载体中的可交换位(NH4+)的量与 CuY催化剂活性间的关系具有非常重要的意义.本文将 NaY分子筛与不同浓度的 NH4NO3溶液进行离子交换,制得具有不同 NH4+交换度的 NaNH4Y分子筛,以其为载体,以具有易升华、易分解性质的乙酰丙酮铜 Cu(acac)2为铜源,在无溶剂条件下,高温热处理二者固相混合物, NaNH4Y 分子筛中的 NH4+与 Cu(acac)2中的 Cu2+发生了离子交换, Cu2+进一步发生自还原生成活性中心 Cu+,成功地制备了完全无氯的 CuY催化剂,应用于催化常压甲醇氧化羰基化合成 DMC过程,研究 NaNH4Y分子筛中的铜离子可交换位 NH4+与催化剂 CuY催化性能间的关系.通过各种表征及对 CuY催化剂在甲醇氧化羰基化过程中催化活性分析发现, Y分子筛经过 NH4NO3溶液离子交换及催化剂的制备过程,其八面沸石结构和孔道保持良好.以未经过离子交换的 NaY负载的 CuY催化剂上的铜物种完全以 CuO形式存在,且没有催化活性.随着 NH4+交换度增加, CuY催化剂表面 CuO含量逐渐降低,而活性中心 Cu+含量逐渐增加,且其催化活性也随之增加.当 NH4+交换度趋于极限值时, CuY催化剂中 Cu+含量达最大,其催化活性也达最佳, DMC的时空收率和选择性分别为267.3 mg/(g·h)和68.5%,甲醇转化率为6.9%.因此,无溶剂条件下,以 NaNH4Y分子筛为载体, Cu(acac)2为铜源,制备完全无氯 CuY催化剂时, NH4+是形成 Cu+活性中心的必须条件,且 NH4+交换度直接影响催化剂 CuY的催化活性.     

草酸钠改性共沉淀制备高效Cu/ZrO2催化剂及其 在甲醇部分氧化制氢反应中的应用

采用四种不同沉淀剂并流共沉淀制备系列Cu/ZrO2催化剂, 结果表明经过Na2C2O4和NaOH改性沉淀的催化剂在甲醇部分氧化制氢反应中表现出比NaOH, Na2CO3和Na2C2O4-Na2CO3沉淀的催化剂更优越的催化性能, 在533 K可获得92%的氢气产率而CO含量低于1.5%, 并且在110 h寿命测试中保持良好的稳定性. 采用X射线粉末衍射, N2低温吸附, H2-TPR, N2O滴定和X射线光电子能谱对其进行系统表征, 阐述了该改性共沉淀法所得催化剂高性能的本质原因.     

液相共沉淀法制备Y3Fe5O12(YIG)超细粉体

以高纯Y2O3,FeCl2·4H2O为原料,用NH3·H2O为沉淀剂,利用液相共沉淀法制备了超细YIG前驱体,经过洗涤、干燥,前驱体在1100 ℃煅烧得到了高纯、颗粒分布均匀的纳米级YIG超细粉体,并就影响粉体性能的诸因素: 滴定终点的pH值,煅烧温度,保温时间等进行了讨论.通过TG-DTA,XRD,SEM等分析手段进行分析,找到了制备具有良好烧结性的YIG超细粉体的最佳工艺条件.     

CuO/CeO2催化剂的催化氧化性能及其表征

用CO流动反应法 ,程序升温还原 (TPR) ,光电子能谱 (XPS)和X射线衍射Rietveld分析等技术研究了CuO ,CeO2 及CuO/CeO2 各组分催化剂。结果表明 :单组分的CuO和CeO2 对CO的氧化活性较低 ,但CuO与CeO2 形成复合氧化物后 ,其CO氧化活性明显提高 ,这可能与铜物种在CeO2 表面的价态 (Cu2 + 和Cu+ ) ,分散状态和还原性能有关。CuO在CeO2 上的负载量对铜物种在CeO2 表面形成的价态 (Cu2 + 和Cu+ )至关重要 ,CuO的负载量为 1 0 %时 ,XPS检测不到Cu2p3/2 (eV)结合能 ;当CuO的负载量为 5 0 %时 ,CuO主要以Cu2 + 和Cu+ 形式存在 ,而负载量大于 5 0 %时 ,CuO则以Cu2 + 形式存在。由于形成了CuO/CeO2 复合氧化物 ,使离子半径小于Ce4 + 的CuO进入了CeO2 晶格 ;当CuO的负载量达到 5 0 %时 ,CuO的晶粒尺寸值为最小 ( 6 1nm) ,而晶格畸变值为最大 ( 2 86× 10 - 3) ,此时 ,催化剂具有较高的表面能和最佳的CO氧化活性     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。