沉淀剂种类对Ru/CeO2氨合成催化剂结构和性能的影响

采用6种沉淀剂通过共沉淀法制备了6种Ru/CeO2氨合成催化剂, 考察了沉淀剂种类对其氨合成性能的影响. 通过X射线衍射、N2吸附-脱附、X射线荧光光谱和H2程序升温还原等表征手段, 对不同沉淀剂影响Ru/CeO2催化剂氨合成性能的原因进行探讨. 结果表明: 采用(NH4)2CO3和NH4HCO3制备的催化剂样品具有较好的氨合成活性, 其中NH4HCO3为最佳沉淀剂, 所制备的催化剂在450 ℃, 10 MPa , 10000 h－1测试条件下, 出口氨浓度为14.46%. 而采用KHCO3, KOH, K2CO3沉淀剂制备的样品的氨合成活性相对较低. 沉淀剂种类不仅明显地影响钌离子和铈离子的共沉淀, 而且会影响载体二氧化铈表面氧的还原. 由NH4HCO3沉淀剂制备的Ru/CeO2催化剂的高活性归因于钌负载量增大、钌粒子分散度提高以及二氧化铈表面氧易还原三者相互作用的结果.     

制备参数对Au／Fe2O3催化剂水煤气变换性能的影响

 采用共沉淀法制备了Au／Fe2O3催化剂，并系统地考察了制备参数对其催化WGS性能的影响．通过BET，XRD，XRF，H2－TPR和HRTEM等表征手段，初步考察了Au／Fe2O3催化剂具有高催化活性的原因．结果表明，金负载量、沉淀剂种类、沉淀方式、沉淀pH值、焙烧气氛和焙烧温度对Au／Fe2O3催化剂的催化性能均具有较大的影响．Au／Fe2O3催化剂的低温高活性是纳米Au与Fe3O4协同作用的结果；Au／Fe2O3催化剂的高温活性是由于活性相Fe3O4起主要作用的结果．纳米Au粒子的烧结会降低其催化活性．     

铜物种对Cu/Fe_2O_3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe2O3水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响.结果表明,Cu/Fe2O3催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250°C时CO转化率高达97.2%,同时热稳定性也最好.运用X射线粉末衍射(XRD)、N2物理吸脱附和H2程序升温还原(H2-TPR)等手段对Cu/Fe2O3催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe2O4物种的存在极大地改善了催化剂的还原性能和WGS反应活性.这是由于CuFe2O4特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe2O4在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移.此外,通过(NH4)2CO3溶液处理,研究了独立相CuO对Cu/Fe2O3催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe2O4的还原,改善Cu/Fe2O3催化剂的WGS反应性能.     

沉淀剂对AU/ZnO催化剂CO氧化性能及催化剂结构的影响

在25 C和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性.结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO氧化性能.由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3种沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1 100 h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂.在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相.催化剂的稳定性与金粒子长大速度和碳酸根累积量有关.     

沉淀剂对Au／ZnO催化剂上CO氧化性能及催化剂结构的影响

在25℃和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性。结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO拉化性能。由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1100h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂。在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相。催化剂的稳定性与金粒子长大速度和碳酸根累积量有关。     

Au/Fe2O3催化剂的制备及其对富氢气体中一氧化碳选择性氧化的催化性能

 采用共沉淀法制备了1.5%Au/Fe2O3催化剂,考察了加料方式对Au/Fe2O3催化剂化学组成及其催化富氢气体中CO选择性氧化性能的影响. 结果表明,正加法制备的Au/Fe2O3催化剂的性能明显好于反加法制备的催化剂,80 ℃时前者对富氢气体中CO选择性氧化反应的转化率为94%,CO2选择性为65%,连续反应10 h,催化剂活性没有变化. XRD,XPS和TEM等的测试结果表明,正加法制备的Au/Fe2O3催化剂中金粒子的平均粒径为2～4 nm,金粒子高度分散在载体上,并与载体之间发生了较强的相互作用,从而表现出较高的催化性能.     

负载纳米金对氧化铁载体结构和水煤气变换催化性能的影响

采用共沉淀法在多种条件下分别制备氧化铁及其负载金催化剂,测定其水煤气变换反应活性.通过BET-PS,XRD,H2-TPR和CO-TPD等表征手段,研究负载纳米金对氧化铁载体结构、结晶行为、还原性能以及CO吸脱附性质的影响,探讨氧化铁负载金催化剂的活性相.结果表明:(1)负载纳米金能抑制氧化铁载体在焙烧时的结晶过程,提高其还原性能以及增加表面CO吸附中心.但这种抑制作用与催化剂的制备条件(如沉淀剂种类、沉淀方式和焙烧温度等)密切相关.(2)氧化铁负载金催化剂的低温高活性(<300℃)可能是纳米金粒子与Fe3O4相协同作用的结果,在高温区(>300℃)仍是Fe3O4相起主要催化作用.     

金负载量对低温水煤气变换Au/α-Fe2O3催化剂结构和性能的影响

采用共沉淀法制备了低温水煤气变换Au/α-Fe2O3催化剂。通过正交实验优化催化剂的还原活化条件，考察了金负载量对催化剂性能的影响。采用BET、XRD、UV-VIS、XRF、H2-TPR和O2-TPO等表征手段对催化剂的结构进行分析，并与其催化性能进行关联。结果表明，（1）采用10%-H2/N2还原气将催化剂在150 ℃原位还原9 h，其催化活性最高；（2）金的最佳负载量为8.00%，此时在催化剂制备过程中金的流失量较少，金粒子较小，也有利于抑制催化剂在反应过程中烧结；（3）TPR-TPO结果表明，金的负载量为8.00%时，Au/α-Fe2O3催化剂具有较易被还原、不易被氧化的性质，从而显示出最高催化活性。（4）Au/α-Fe2O3催化剂中的金以单质金（Au0）形式存在；其高活性与Au0-Fe3O4间的协同作用有关。     

改性沉积-沉淀法制备Au/Fe2O3水煤气变换反应催化剂

采用共沉淀法、沉积-沉淀法和改性沉积-沉淀法制备了Au/Fe2O3催化剂,运用N2吸附、X射线衍射、X射线光电子能谱和透射电镜等技术对其进行了表征,考察了制备方法对Au/Fe2O3催化剂水煤气变换反应催化活性的影响.结果表明,改性沉积-沉淀法制备的催化剂具有最好的催化活性,150℃时CO转化率达82.3%.该催化剂比表面积较大,金粒子尺寸(3~5nm)较小且分布均匀.载体氧化铁以无定形态和结晶态共存,金与载体间存在较强的相互作用,这对催化剂活性的提高起着重要作用.     

助剂对低温水煤气变换反应Au/αFe2O3催化剂性能的影响

采用共沉淀法制备了系列Au/αFe2O3 MOxM=Zr、Al、Mg、Ca、Ba)催化剂，通过N2物理吸附、XRD、H2-TPR和CO2-TPD-MS等手段对催化剂的物化性质进行表征，考察了富氢下低温水煤气变换（WGS）反应中助剂对Au/αFe2O3催化剂性能的影响。结果表明，助剂ZrO2能有效提高Au/α Fe2O3催化剂在富氢气氛下低温WGS反应活性和稳定性，反应温度150℃时CO转化率可达88.45%，且催化剂具有较高的稳定性。研究发现，添加ZrO2助剂能抑制载体晶粒的生长，降低载体晶粒度，提高催化剂的比表面积，改善催化剂的还原性能和表面酸碱度，从而提高催化剂的催化活性和稳定性。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.