基于PREF的扫描磁铁电源设计与实现

PREF装置是中国科学院新疆理化技术研究所与近代物理研究所联合设计建造的10～60 MeV质子同步加速器,属于国内唯一的位移损伤效应模拟试验专用装置。针对该装置的扫描磁铁电源输出电流频率200 Hz、跟踪误差小于≤±5×10^-3的技术要求,采用三组H桥串联拓扑方案,通过移相控制,基于脉宽调制实现技术要求。经仿真与测试结果表明：电源能够输出峰-峰值为±420 A,幅值与频率均连续可调的高精度三角波电流,满足工程应用要求。     

硅单粒子位移损伤多尺度模拟研究

本文结合分子动力学方法和动力学蒙特卡罗方法, 研究了单个粒子入射硅引起的位移损伤缺陷的产生和演化过程; 基于Shockley-Read-Hall理论计算了单个粒子入射引起的位移损伤缺陷导致的泄漏电流增加及其演化过程, 比较了缺陷退火因子与泄漏电流退火因子之间的差异, 并将计算结果与实验值进行了对比. 结果表明, 计算泄漏电流时, 仅考虑一种缺陷的情况下缺陷退火因子与泄漏电流退火因子相同, 考虑两种缺陷类型情况下二者在数值上有所区别, 但缺陷退火因子仍能在一定程度上反映泄漏电流的退火行为. 分子动力学模拟中采用Stillinger-Weber势函数和Tersoff势函数时缺陷退火因子和泄漏电流退火因子与实验结果一致, 基于Stillinger-Weber势函数的计算结果与实验值更为接近.     

退火对Pb辐照Al2O3单晶发光特性的影响

研究了230MeV的²⁰⁸Pb²⁷⁺辐照Al₂O₃样品及随后在600,900,1100K高温条件下退火后的光致发光特性。从辐照样品的测试结果可以清楚地看到在波长为390,450nm处出现了强的发光峰。辐照量为1×10¹³ions/cm²时,样品的发光峰最强。经过600K退火2h后测试结果显示,380nm发光峰剧烈增强,而其他发光峰显示不明显。在900K退火条件下,380nm的发光峰开始减弱,而在360,510nm出现了明显的发光峰,至到1100K退火完毕后380nm的发光峰完全消失,而360,510nm的发光峰相对增强。从被辐照样品的FTIR谱中看到,波数在460~510cm^-1间的吸收是振动模式,经过离子辐照后,吸收带展宽,随着辐照量的增大,Al₂O₃振动吸收峰消失,说明Al₂O₃振动模式被完全破坏。1000~1300cm^-1之间为Al—O—Al桥氧的伸缩振动模式,辐照后吸收带向高波数方向移动,说明其振动模式受到影响。辐照剂量较小的样品,损伤程度相对较低,经退火晶化后,振动模式基本恢复到单晶状态;辐照剂量较高的样品,损伤程度大,退火处理后表面变得较粗糙,振动模式并未出现,说明结构破坏严重。     

退火对He注入及随后208Pb27+辐照的Al2O3单晶PL谱的影响

利用高能离子研究了110 keV 的He⁺注入Al₂O₃单晶及随后230 MeV的²⁰⁸Pb²⁷⁺辐照并在不同温度条件下退火样品的光致发光的特性. 从测试结果可以清楚地看到在375 nm，390 nm，413 nm 和450 nm 出现了强烈的发光峰. 经过600 K退火2 h后测试结果显示，390 nm发光峰增强剧烈，而别的发光峰显示不明显. 在900 K退火条件下，390 nm的发光峰开始减弱相反在510 nm出现了较强的发光峰，到1100 K退火完毕后390 nm的发光峰完全消失，而510 nm的发光峰相对增强. 从辐照样品的FTIR谱中看到，波数在460—510 cm^-1间的吸收是振动模式，经过离子辐照后，吸收带展宽，随着辐照量的增大，Al₂O₃振动吸收峰消失，说明Al₂O₃振动模式被完全破坏. 1000—1300 cm^-1之间为Al-O-Al桥氧的伸缩振动模式，辐照后吸收带向高波数方向移动. 退火后的FTIR谱变化不大.     

快重离子辐照引起Ni/SiO2界面原子混合及相变研究

在室温下用308 MeV的Xe离子和853 MeV的Pb离子辐照Ni/SiO2样品, 用卢瑟福背散射和X射线衍射技术对样品进行了分析。 通过分析Ni/SiO2样品中元素成分分布和结构随离子辐照剂量和电子能损的变化, 探索了离子辐照在Ni/SiO2样品中引起的界面原子混合与结构相变现象。 实验结果显示, Xe和Pb离子辐照均能引起明显的Ni原子向SiO2基体的扩散并导致界面附近Ni, Si和O原子的混合。 实验观测到低剂量Xe离子辐照可产生NiSi2相, 而高剂量Xe离子辐照则导致了Ni3Si和NiO相的形成。 根据热峰模型, Ni原子的扩散和新相的形成可能由沿离子入射路径强电子激发引起的瞬间热峰过程驱动。Ni/SiO2 interface were irradiated at room temperature with 308 MeV Xe ions to 1×1012, 5×1012 Xe/cm2 and 853 MeV Pb ions to 5×1011 Pb/cm2, respectively. These samples were analyzed using Rutherford Backscattering Spectrometry (RBS) and X ray diffraction spectroscopy (XRD), from which the intermixing and phase change were investigated. The obtained results show that both Xe and Pb ions could induce diffusion of Ni atoms to SiO2 substrates and result in intermixing of Ni with SiO2. Furthermore, 1.0×1012 Xe/cm2 irradiation induced the formation of NiSi2 and 5.0×1012 Xe/cm2 irradiation created Ni3Si and NiO phases. The diffusion of Ni atoms and the formation of new phase may be driven by a transient thermal spike process induced by the intense electronic energy loss along the incident ion path.     

94MeV Xe离子辐照引起的薄膜硅光学带隙变化研究

室温下,用94MeV的Xe离子辐照纳米晶和非晶硅薄膜以及单晶硅样品,辐照量分别为1.0×1011,1.0×1012和1.0×1013ions/cm2。所有样品均在室温下用UV/VIS/NIR光谱仪进行检测分析。通过对比研究了纳米晶、非晶、单晶硅样品的光学带隙随Xe离子辐照量的变化。结果表明,不同结构的硅材料中Xe离子辐照引起的光学带隙变化规律差异显著:随着Xe离子辐照量的增加,单晶硅的光学带隙基本不变,非晶硅薄膜的光学带隙由初始的约1.78eV逐渐减小到约1.54eV,而纳米晶硅薄膜的光学带隙则由初始的约1.50eV快速增大至约1.81eV,然后再减小至约1.67eV。对硅材料结构影响辐照效应的机理进行了初步探讨。     

Fe/Nb多层膜中离子辐照效应研究(英文)

〗采用磁控溅射技术在Si衬底上沉积Si/\[Fe(10 nm)/Nb(4 nm)/Fe(4 nm)/Nb(4 nm)\]2/ \[Fe(4 nm)/Nb(4 nm)\]4多层膜。 用2 MeV的 Xe离子在室温下辐照多层膜。采用俄歇深度剖析、X射线衍射和振动样品磁强计分析辐照引起的多层膜元素分布、 结构及磁性变化。AES深度剖析谱显示当辐照注量达到1.0×1014 ions/cm2时, 多层膜界面两侧元素开始混合; 当辐照注量达到2.0×1016ions/cm2时, 多层膜层状结构消失, Fe层与Nb层几乎完全混合。XRD谱显示, 当辐照注量达到1.0×1014ions/cm2时, Nb的衍射峰和Fe的各衍射峰的峰位相对于标准卡片向小角方向偏移, 这说明辐照引起Nb基和Fe基FeNb固溶体相的形成;当辐照注量大于1.0×1015 ions/cm2时, 辐照引起非晶相的出现。 VSM测试显示,多层膜的磁性随着结构的变化而变化。 在此实验基础上, 对离子辐照引起界面混合现象的机理进行了探讨。The behavior of the metallic multilayers of Si/\[Fe(10 nm)/Nb(4 nm)/Fe(4 nm)/ Nb(4 nm)\]2/\[Fe(4 nm)/Nb(4 nm)\]4 under 2 MeV Xe ion irradiation has been investigated by depth profile analysis of Auger electron spectroscopy,X ray diffraction and vibrating sample magnetometer. The obtained experimental results show that the inter mixing between Fe and Nb layers occurs in the 1.0×1014 ions/cm2 irradiated multilayer sample which results in the formation of Nb based and Fe based FeNb solid solution. For the samples irradiated to fluence larger than 1.0×1014 ions/cm2, amorphisation is observed, and moreover, the layered structure of the multilayer samples is broken up completely for the samples under 1.0×1016 or 2.0×1016 ions/cm2 irradiation. Vibrating sample magnetometer measurement also reveals that the magnetization of the samples changes with the evolution of the structure of multilayers. Possible mechanism of the modification in Fe/Nb multilayers induced by Xe ion irradiation is briefly discussed.     

80keV N离子注入对ZnO薄膜结构的影响

室温下用80keVN离子注入ZnO薄膜样品,注量分别为5.01014,5.01015和5.01016ions/cm2,然后用X射线衍射和透射电镜技术对样品的结构特性进行了表征。实验结果表明,由高度(002)择优取向的致密柱状晶构成的薄膜中,注入5.0×1015ions/cm2时,观测到缺陷生成和局域无序化现象,但薄膜总体结构仍保持柱状晶和(002)择优取向;随着注量的增大,晶格常数c和压应力呈增大趋势。对注入N离子对ZnO薄膜结构特性的影响机理进行了简单的讨论。     

Investigation of PL properties of C-doped SiO2/Si samples after high energy Pb ion irradiation

Amorphous SiO₂ thin films with about 400—500 nm in thickness were thermally grown on single crystalline silicon. These SiO₂/Si samples were firstly implanted at room temperature (RT) with 100 keV carbon ions to 2.0×10¹⁷, 5.0×10¹⁷ or 1.2×10¹⁸ ions/cm², then irradiated at RT by 853 MeV Pb ions to 5.0×10¹¹, 1.0×10¹², 2.0×10¹² or 5.0×10¹² ions/cm², respectively. The variation of photoluminescence (PL) properties of these samples was analyzed at RT using a fluorescent spectroscopy. The obtained results showed that Pb-ion irradiations led to significant changes of the PL properties of the carbon ion implanted SiO₂ films. For examples, 5.0×10¹² Pb-ions/cm² irradiation produced huge blue and green light-emitters in 2.0×10¹⁷ C-ions/cm² implanted samples, which resulted in the appearance of two intense PL peaks at about 2.64 and 2.19 eV. For 5.0×10¹⁷ carbon-ions/cm² implanted samples, 2.0×10¹² Pb-ions/cm² irradiation could induce the formation of a strong and wide violet band at about 2.90 eV, whereas 5.0×10¹² Pb-ions/cm² irradiation could create double peaks of light emissions at about 2.23 and 2.83 eV. There is no observable PL peak in the 1.2×10¹⁸ carbon-ions/cm² implanted samples whether it was irradiated with Pb ions or not. All these results implied that special light emitters could be achieved by using proper ion implantation and irradiation conditions, and it will be very useful for the synthesis of new type of SiO₂-based light-emission materials.     

Modification of Fe/Cu multilayers under 400 keV Xe20+ irradiation

Two kinds of Fe/Cu multilayers with different modulation wavelength were deposited on cleaved Si(100) substrates and then irradiated at room temperature using 400 keV Xe²⁰⁺ in a wide range of irradiation fluences. As a comparison, thermal annealing at 300—900℃ was also carried out in vacuum. Then the samples were analyzed by XRD and the evolution of crystallite structures induced by irradiation was investigated. The obtained XRD patterns showed that, with increase of the irradiation fluence, the peaks of Fe became weaker, the peaks related to Cu-based fcc solid solution and Fe-based bcc solid solution phase became visible and the former became strong gradually. This implied that the intermixing at the Fe/Cu interface induced by ion irradiation resulted in the formation of the new phases which could not be achieved by thermal annealing. The possible intermixing mechanism of Fe/Cu multilayers induced by energetic ion irradiation was briefly discussed.