丝光沸石水蒸气/酸浸渍脱铝的多核固体核磁共振研究

采用¹H,²⁹Si,²⁷Al魔角旋转固体核磁共振(MASNMR)及¹H-²⁹Si交叉极化(CP)技术研究丝光沸石水蒸气/酸浸渍脱铝过程中各种铝物质的结构与性质.结果表明,丝光沸石上骨架铝原子在水分子作用下,生成非骨架四配位铝物质[Al(OH)₃(H₂O)],分别在²⁷Al谱δ45和¹H谱δ3.0处出现共振信号,这种铝物质不同于扭曲四配位铝,在高温下进一步水合生成Al(OH)₃(H₂O)₂和Al(OH)₃(H₂O)₃,即非骨架五配位和六配位铝物质.¹H-²⁹SiCP和¹H谱证实,水蒸气脱铝使丝光沸石产生了大量的硅羟基和铝羟基.     

乙醇制1,3-丁二烯MgO/SBA-15催化剂的制备及其催化性能

以介孔分子筛SBA-15为载体,采用浸渍法制备了新型负载型MgO/SBA-15催化剂,采用低温N₂吸附-脱附、X射线衍射(XRD)、透射电子显微镜(TEM)、²⁹Si核磁共振(²⁹Si NMR)、NH₃程序升温脱附(NH₃-TPD)、CO₂程序升温脱附(CO₂-TPD)等表征手段研究了不同MgO负载量(质量分数)对催化剂的结构、物化性能和催化乙醇合成丁二烯反应活性的影响。 研究结果表明,MgO负载量为20%时,所制备的催化剂的活性最好,此时MgO高度分散在载体SBA-15的有序孔道中,形成了Mg-O-Si结构,有利于提高目标产物丁二烯的选择性。 该催化剂在温度350 ℃、进料质量空速2.64 h^-1的反应条件下,可获得最佳催化效果,乙醇转化率最高可达55.8%,丁二烯选择性可达80.2%。 MgO/SBA-15催化剂在乙醇法生产丁二烯工艺中具有潜在的应用前景。     

甲胺改性酸碱双功能Y沸石的制备和表征

以甲胺水溶液为改性剂, H-Y沸石可在416 K下经水热反应制备酸碱双功能甲胺杂化H-Y沸石. X 射线粉末衍射(XRD), 固体29Si魔角核磁共振(29Si MAS NMR)表征表明甲胺分子与H-Y相互作用导致沸石晶胞体积明显增大, 骨架产生新的Si—N键. 以热重(TG/DTG)及差热分析(DTA), NH3, CO2程序升温脱附(NH3-TPD和CO2-TPD)研究杂化H-Y沸石的酸-碱性质及其经不同温度焙烧后的变化, 结果表明, 杂化后沸石的酸/碱量, 尤其是后者增加甚大. 与H-Y相比, 随焙烧温度变化, 该酸-碱双功能沸石材料的酸/碱量可分别提高3至7倍和1.5至26倍.     

ZK-4、NaA和NaHS3种沸石的铝化

用高温气-固相置换法对ZK-4、NaA和NaHS3种沸石进行铝化。组成分析、尾气分析、X射线衍射、晶体形貌分析、红外光谱和²⁹Si高分辨魔角固体核磁结果表明,3种低硅铝比沸石铝化后骨架可能存在Al-O-Al键。     

CXN天然沸石的研究 V. 结构超稳化

以离子交换结合控制焙烧的方法分别制得结构超稳化高硅H-STI-I和H-STI-II沸石. EDX, ²⁹Si MAS NMR, ²⁷Al MAS NMR, FT-IR等表征证明, 其骨架硅铝原子比分别为4.43和10.62. 分段程序升温焙烧后的沸石样品经粉末XRD表征表明, 其结构热稳定性达到1000 ℃以上. 结构稳定化沸石呈现反映微孔特性的I型吸附等温线, 吸附孔道完美、开放. 经历过酸处理的H-STI-II沸石, 结构缺陷增多, 其热稳定性、比表面积及孔容积略低于H-STI-I.     

CXN天然沸石的研究 VI. 耐酸性及不同阳离子型沸石结构的热稳定性

以X射线粉末衍射(XRD)结晶度测定法观测CXN (STI型)天然沸石在不同浓度盐酸(HCl)热溶液中的结构耐酸性, 以及比较和研究用不同方法制备的结构超稳化高硅H-STI-I和H-STI-II沸石及其不同阳离子交换型M-STI (M＝Li, Na, K, Ca, Ag) 系列沸石在程序阶梯升温过程中的结构热稳定性. 用X射线荧光散射(XRF), ²⁹Si与²⁷Al固体核磁共振(MAS NMR)表征超稳化高硅H型沸石的组成与结构性质. 结果表明该天然沸石在浓度低于2 mol/L盐酸中可较长时间保持结构完美. 视阳离子类型不同, 经1173 K焙烧后M-STI-I系列沸石与M-STI-II系列沸石相对结晶度降低百分数分别为2.5%～18% 与0～35%. 在M-STI-I系列沸石中, 焙烧前后相对结晶度下降幅度的次序为K型＜(H, Li, Na)型＜(Ca, Ag)型, 而M-STI-II系列沸石, (Na, K)型＜(Li, H, Ca)型＜Ag型. 从沸石骨架硅铝比、结构缺陷、阳离子种类及其氧化物形成热等方面讨论影响沸石结构热稳定性的因素.     

高氯酸铵热分解机理的密度泛函理论研究

深入理解高氯酸铵的热分解机理,对于优化固体推进剂配方设计十分重要.我们采用对称破缺密度泛函方法(BS-UB3LYP/6-311+G(d,p)),对高氯酸铵的热分解机理进行了系统的梳理和深入研究.首先,高氯酸铵通过质子转移,生成HClO₄和NH₃,从吸附态进入气相.进而高氯酸的Cl—OH键均裂,生成羟基自由基·OH和三氧化氯自由基·ClO₃,它们优先和NH3反应,生成·NH₂.·NH₂和HClO₄反应生成·ClO₄自由基,进而和NH₃反应生成H₂NO,再被自由基物种拔H生成NO. NO和·OH反应生成NO₂,和·NH₂及·OH反应生成N₂O.这些产物与诸多实验观测结果一致.     

NH4Y沸石分子筛上质子的运动(Ⅰ)——用CNDO/2法计算氨在HY沸石上的吸附热及质子在NH4Y内的迁移

用CNDO/2方法定量计算氨在HY(Si/Al=2.4)沸石上的吸附热,其值24.4kcal/mol与实验值符合较好。质子在表面与NH₃间迁移,有两个能量极小值;吸附时,质子从接近表面的极小迁移到接近NH₃极小时,要越过势垒9.40kcal/mol;反之要越过势垒11.9kcal/mol。400℃时,质子在表面与NH₃间跳动频率为1.92×10⁹sec^-1。NH₃吸附后,NH键长增加,加以质子迁移,导致NH₈上负电荷密度向沸石表面迁移,使H上的电子集居数减少,H更质子化。     

水热条件下Y型沸石的转晶行为

系统研究了以KOH为结构导向剂,Y型沸石（HY和NaY）在水热条件下转晶为MER型沸石的行为.MER型沸石是硅铝比（Si/Al）在2~3之间且具有四种尺寸8元环孔道（3.1Å×3.5Å,2.7Å×3.6Å,3.4Å×5.1Å,3.3Å×3.3Å）的硅铝沸石分子筛,在小分子催化以及分离方面具有重要的潜在应用.传统水热法合成高结晶度MER型沸石需要7~10 d,将Y型沸石置于KOH的溶液中,经水热处理可在2 d内生成高结晶度的MER型沸石,而水热处理具有等价摩尔组成的无定形硅铝凝胶则得不到高结晶度MER型沸石的纯相.HY沸石可在100和150℃发生转晶,而NaY则只能在150℃发生转晶.KOH/SiO₂比和H₂O/SiO₂比对Y型沸石的转晶行为有重大的影响,只有在最优KOH/SiO₂比和H₂O/SiO₂比条件下才能生成高结晶度的MER型沸石.该转晶合成法显著缩短了MER型沸石的合成周期,对缩短其它有重大工业应用价值的沸石分子筛的合成周期有重要的借鉴意义.     

高硅FAU沸石与甲胺吸附物的相互作用

合成高硅沸石中所用的模板剂胺类分子与沸石骨架 Si—O基团间的相互作用机理尚不清楚 .迄今为止 ,沸石与吸附胺之间的相互作用的研究还只限于测定沸石酸性质 [1,2 ]、表面羟基活性位或了解模板分子在沸石骨架中的位置和状态 [3,4 ] .甲胺、乙胺在骨架完美的高硅 FAU(Y型 )沸石上的亲和性指数 AT 值 ,即被吸附有机物脱附峰温与该有机物的沸点之差分别高达 1 60与 1 5 0℃[5] .而在高硅 MFI(Silicalite-1 )沸石上为 1 60与 1 2 7℃ [6 ] .与大多数有机物不同 ,被吸附的胺类脱附时的吸热效应十分明显 .上述现象表明胺与高硅沸石骨架 O2 -…     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.