贵金属对钴基催化剂上肉桂醛选择加氢反应的影响

 研究了贵金属改性的Co／γ－Al2O3催化剂上的肉桂醛选择加氢反应．结果表明，通过Pt，Pd和Ru贵金属改性，提高了催化剂的活性，但只有Pt改性的催化剂具有较高的选择性．w（Pt）＜0．5％时，催化剂的活性随着Pt含量的增加呈直线升高，当w（Pt）＝0．5％时，催化剂活性可提高近5倍，但催化剂的选择性变化很小．XRD结果表明，催化剂经还原后，γ－Al2O3上的钴主要为α－Co0．TPR结果表明，Pt的加入提高了Co3O4的还原性能，且Pt含量越高，Co3O4的还原温度越低．XPS结果表明，Pt改性的催化剂样品，其Co3O4大部分被还原为Co0．由于Pt与Co具有协同效应，故Pt改性的Co／γ－Al2O3催化剂既具有较高的活性，又具有很高的选择性．     

Ni/CaO-SiO2对流化床反应器中甲烷转化制合成气的催化性能

用浸渍法制备了Ni／SiO2和Ni／CaO—SiO2催化剂．研究了流化床反应器中用CaO改性微球硅胶载体对催化性能的影响，考察了Ni／CaO—SiO2催化剂上甲烷部分氧化与甲烷二氧化碳重整耦合制合成气反应中Ca负载量、反应温度、空速和原料气中的O2／CO2比对活性与选择性以及产物H2／CO比的影响。并用XRD、TEM、H2-TPR和CO2-TPD等测试手段对催化剂进行了表征。结果表明，经过氧化钙改性的微球硅胶能够将“自由态”的镍物种转变为“束缚态”。使镍物种达到高度分散状态。引入10(wt)％Ca助剂所制备的催化剂具有很好的活性和稳定性，因而具有较好的工业应用前景。     

Pd(Ni)对铜基催化剂的调变及对顺酐选择性加氢产物的调控

 考察了在Cu－Ti－Al－O催化剂中添加Pd（或Ni）对活性中心Cu的调变作用及对顺酐加氢产物的调控．结果表明，Cu－Ni－Ti－Al－O是优良的顺酐选择性加氢制γ－丁内酯（GBL）反应的催化剂，催化剂中Cu和Ni含量的改变会影响加氢深度．当Cu含量较Ni含量高时，可以得到第三步加氢产物1，4－丁二醇和四氢呋喃，在270℃下其选择性为17．3％；当Ni含量较Cu含量高时，GBL选择性可达到100％．添加微量的Pd后，可加速活性组分Cu的还原，使Cu的还原更加彻底，获得纳米尺寸更小和晶格畸变率更大的Cu0晶粒，使顺酐第三步加氢产物的选择性显著提高．使用Cu－Pd－Ti－Al－O（n（Pd）／n（Cu）＝0．08％）催化剂，在240℃下顺酐转化率为100％，1，4－丁二醇与四氢呋喃选择性为38．5％．     

FCC抗重金属催化剂的研究进展

20世纪80年代以来，随着世界原油日趋重质化和劣质化，各国炼厂都大力发展掺炼或全炼重油和渣油的流化催化裂化（FCC）技术，以拓宽FCC原料油来源，满足全球市场对轻质油品的需求，最大限度的提高经济效益．与常规FCC原料油（如AGO和VGO）相比，渣油或重油中Ni、V、Fe、Cu等金属含量明显偏高，严重污染了FCC催化剂，其中影响最大的是镍和钒，它们沉积在催化剂上，导致催化剂裂化活性下降，产物选择性变差，当钒含量很高时还能破坏分子筛结构，     

助剂镍/钴对磷化钨催化剂加氢精制性能的影响

在共浸渍法制备磷化钨／γ-Al2O3催化剂基础上，分别加人1％、3％、5％、7％和9％(占活性组分比例)的助剂镍或钴，制得负载30％含助剂镍／钴磷化钨／γ-Al2O3系列催化剂，考察了助剂及其加人比例对催化剂加氢脱硫和加氢脱氮性能的影响．结果表明，加人适当比例的助剂镍或钴，有利于提高磷化钨／γ-Al2O3催化剂的加氢脱硫活性，当助剂含量分别为5％镍或7％钴时，催化剂的噻吩加氢脱硫率最高；助剂镍对磷化钨／γ-Al2O3催化剂的加氢脱氮反应不利，而加人适当比例助剂钴有利于提高催化剂加氢脱氮活性，当助剂钴含量为5％时，催化剂吡啶加氢脱氮率最高．温度对磷化钨／γ-Al2O3催化剂加氢精制性能有一定影响，高温有利于加氢脱硫反应，低温有利于加氢脱氮反应．     

Pd-SiW12/SiO2催化剂上乙烯直接氧化制乙酸的反应机理

 利用积分反应器和微分反应器对Pd－SiW12／SiO2催化剂上乙烯直接氧化生成乙酸的反应机理进行了探讨．乙烯在积分反应中氧化的主要产物为乙酸（选择性为77．6％），很少生成乙醛（选择性仅为8．1％）；而在微分反应中氧化的主要产物是乙醛（选择性为98．4％）．在微分反应中分别以乙醛和乙醇为主反应物时，乙醛氧化完全生成乙酸，选择性为100％，而乙醇氧化生成乙酸的选择性低于0．15％．可以认为，在Pd－SiW12／SiO2催化剂上，水蒸气存在下乙烯主要经由中间物乙醛而生成乙酸．通过对含有不同组分和不同还原条件处理的催化剂活性的比较，认为目的反应主要发生在Pd与SiW12相互接触的部位，催化剂中的Pd0是活性Pd物种的主要形态．     

Co/γ-Al_2O_3催化剂上肉桂醛的选择加氢──反应性能的考察

研究了γ－Al2O3负载的Co／γ－Al2O3催化剂上肉桂醛的选择加氢反应．反应结果表明,以CoCl2作为前驱物的Co／γ－Al2O3催化剂的选择性要高于以Co（NO3）2作为前驱物的Co／γ－Al2O3催化剂,而活性则正好相反．当钴的负载量小于9％时,随着钴负载量的增加,催化剂的活性和选择性随之增加,当钴的负载量大于9％时,随着钴负载量的增加,Co／γ－Al2O3催化剂的活性略有增加,而生成肉桂醇的选择性变化也很小,认为9％的钴负载量是催化剂反应活性和选择性的一个阈值．在所选定的范围内,反应温度和压力对肉桂醛加氢的选择性几乎没有影响．     

镍基催化剂的制备、表征及选择加氢性能

研究了溶胶-凝胶-超临界流体干燥法（sol-gel-SCFD）和浸渍法（IM）制备的SiO2负载镍催化剂的顺酐液相加氢性能,并用XRD、TPR、IR等手段对催化剂的体相和表面结构进行了表征.结果表明: 1) Sol-Gel-SCFD法制备的催化剂其体相和表面结构与镍含量有关,当镍含量 < 30％(质量分数)时,NiO主要以簇团形式存在;随镍含量增高到50％,过量的NiO以微晶态存在并覆盖部分NiO簇团.顺酐(MA)加氢产物有丁二酸酐(SA)和γ-丁内酯(γ-BL),它们的选择性随镍含量增加呈规律性变化;在镍含量为30％的催化剂上γ-BL选择性呈现最大值. 2) IM法制备的催化剂其体相和表面结构与镍含量无关,当镍含量在6％～30％范围内变化时,NiO都以结晶态存在,MA加氢产物为SA; NiO与SiO2的相互作用随镍含量增加而减弱,SA的选择性不变.     

甲烷部分氧化Ni催化剂及助剂的研究

考察了不同Ni担载量的Ni／a－Al_2O_3催化剂的催化性能，以8％Ni（质量分数）最佳．XRD分析表明，8％Ni催化剂表面NiO颗粒最小．TPR分析表明，催化剂表面主要有两种不同化学环境的NiO，当Ni担载量超过12％时，表面开始出现“游离态”NiO，这部分NiO易使催化剂积碳．添加稀土Ce有利于提高Ni催化剂的活性、选择性和稳定性，并对Ce的助剂效应作了研究．     

Cr2O3-Co3O4／SiO2对十八醇氧化生成十八酸反应的催化性能

 制备了一系列不同Cr／Co比例的Cr2O3－Co3O4／SiO2催化剂，并用XRD，FT－IR和BET等手段对催化剂进行了表征；考察了催化剂对十八醇氧化生成十八酸反应的催化性能，及反应条件（反应温度和反应时间）对催化性能的影响，确定了最佳反应条件．结果表明，金属硝酸盐在773K焙烧后转变成相应的氧化物并负载于二氧化硅上．Cr2O3－Co3O4／SiO2催化剂对十八醇氧化反应有很高的催化活性，十八酸选择性最高可达99．93％，收率可达52．44％．Cr2O3－Co3O4／SiO2催化剂的活性明显高于单一的Cr2O3／SiO2或Co3O4／SiO2催化剂     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.