大黄素衍生物的合成及抗癌活性

通过对大黄素的C6位进行化学修饰, 设计合成了7个含氮杂环的大黄素衍生物和3个含季铵盐基团的大黄素衍生物. 通过红外光谱、 ¹H NMR和质谱表征了所制备化合物的结构, 并测试了它们对白血病细胞Molt-4和淋巴瘤细胞CA46的体外抑制活性. 其中化合物8, 9a+9b, 20a, 20b和20c均显示出比大黄素更高的抗癌活性, 表明苯并咪唑基团和季铵盐基团是大黄素提高抗癌活性的有效药效团.     

芦荟大黄素1.5阶微分阳极溶出伏安法测定及电化学性质研究

研究了芦荟大黄素在以 0 .1mol/LHAc (pH 2 .89)为支持电解质 ,玻碳电极为工作电极的吸附伏安行为 .结果表明芦荟大黄素存在一个准可逆的双电子转移过程 ,其峰电流Ip 和峰电位Ep 与溶液 pH值有关 .同时还建立了用 1.5阶微分阳极溶出伏安法测定含量的新方法 .在 - 0 .80V(vs.SCE)电位下富集 ,可得一灵敏的微分阳极溶出峰 ,峰电位Ep 为 - 0 .38V ,峰电流Ip 与芦荟大黄素的浓度在 2 .0× 10 - 7～ 8.0× 10 - 6 mol/L范围内成线性关系 ,最低检出限为 1.0× 10 - 7mol/L .该法用于含有芦荟大黄素体系的测定 ,具有简便、快速、准确等优点     

胶束1,3-亚乙氧基链双季铵盐相转移催化反常Reimer-Tiemann反应

随着非均相有机合成的发展,活性高、功能多、用量少的相转移催化剂~[1～3]的研究与应用已有较多报道.1,3-亚乙氧基链双季铵盐是一种新的有效的双官能团相转移催化剂,在相催化反应中显示出优良的催化特性~[4,5].该类催化剂为既含有1,3-亚乙氧基链,末端又有季铵盐的结构(BTMO CI,BTMU CI),当氮上连有长链烷基(如十八碳烷基)后,形成的胶束双季铵盐相转移催化剂(BDMOU I)可相应地改变催化性能.     

二-(2-羟基-5-长链烷基苯基)-甲烷的合成

以脂肪酸、苯酚为原料, 经酰化反应、酯化反应、Fries重排、黄鸣龙还原等步骤, 得到正构长链烷基酚, 再与多聚甲醛在酸性催化剂下进行缩合反应, 生成二-(2-羟基-5-长链烷基苯基)-甲烷, 用核磁共振氢谱和碳谱、红外光谱和元素分析对产物进行了结构鉴定. 据上述反应路线, 以工业品壬基酚和多聚甲醛为原料, 合成出了二-(2-羟基-5-壬基苯基)-甲烷, 并对其工艺条件进行了研究. 结果表明, 选用草酸作催化剂, 烷基酚和甲醛物质的量比为2∶1, 130 ℃反应4 h, 产物产率达到60%, 且反应转化率和选择性分别为63%和95%.     

反式-3-苯基-12-取代环十二酮的合成及晶体结构

以环十二酮为原料,经2-碘酰基苯甲酸(IBX)氧化制备2-环十二烯酮,在醋酸钯和三苯基磷催化下,2-环十二烯酮与苯硼酸反应制得3-苯基环十二酮.经3-苯基环十二酮与不同试剂发生区域选择性反应制备了一系列新的3-苯基-12-取代环十二酮衍生物,采用核磁共振波谱(NMR)和液相色谱-高分辨质谱(HRMS)表征了其结构.在溶液中结晶,获得了4个代表性化合物的单晶并进行X射线衍射分析,结果表明,3-苯基-12-取代环十二酮晶体中的十二元环仍采取[3333]-2-酮构象,2个取代基为反式构型,取代基存在2种情形:2个取代基在同一条边上,苯基位于与羰基间隔1个亚甲基的β-角碳反向位,而另1个取代基位于与羰基另一侧相邻的α-角碳顺向位;或2个取代基在2条边上,苯基位于与羰基间隔1个亚甲基另一条边的β-边碳外向位,而另1个取代基位于与羰基另一侧相邻并在同一条边的α-边碳外向位,量子力学计算结果与晶体衍射分析结果一致.     

多核季胺盐类功能分子筛模板剂的合成

以1,6-己二醇,二正丙胺和三正丙胺为原料,合成了长链双核季铵盐和三核季铵盐功能MFI型分子筛模板剂,其结构经13C NMR和IR表征.     

β-萘酚α位反应的研究进展

萘酚是有机合成中一种重要的合成子,其α位化学性质活泼,可参与多种化学反应,受到了化学家的广泛关注. β-萘酚的α位可以发生多种化学转化,如烷基化、芳基化、环化、胺化和卤化等,利用这些化学反应可以构建结构多样化且具有不同生物活性的萘酚衍生物.这些萘酚衍生物既可以作为天然活性药物的关键骨架,也可以用于制备化学合成中的重要中间体.基于近年来β-萘酚α位的化学反应层出不穷,主要从β-萘酚α位碳-碳键和碳-杂键(C—N,C—O, C—X, C—S, C—P)的构建来对β-萘酚α位的相关反应进行了综述.     

一锅法合成两种含有季碳中心的氰基化合物（英文）

α-溴代酰胺和亲电氰化试剂在锌粉存在条件下转化为相应的含有季碳中心的α-氰基酰胺和烯酮亚胺锌中间体;向反应体系中引入亲电试剂捕获该中间体,顺利得到另一种含有季碳中心的氰基产物,实现了一锅法合成两种含有季碳中心的氰基化合物.该反应体系可以构建含有碳-碳、碳-硫或碳-氟键的季碳中心.该方法可用于关键药物中间体如洛哌丁胺、普罗地芬、维拉帕米、戈洛帕米、α-氟代布洛芬以及α-氟代氟比洛芬的形式合成,体现了其潜在应用价值.     

PVC膜四氯络铁(Ⅲ)阴离子电极的研制

Cattrall等_[1]曾报导用Allqat 336S的四氯络铁(Ⅲ)酸盐为电活性物质制成铂基PVC膜涂层电极,并用于测定铁矿石中的铁含量_[2]。惜所用季铵盐碳链较短,检测下限欠佳。本文报导用长键季铵盐作活性物质,以制备其内导体系为溶液接触型的PVC膜四氯络铁(Ⅲ)阴离子选择电极的研究结果。     

毛细管电泳法测定β-环糊精与芦荟大黄素包合反应平衡常数

在25 ℃条件下,利用毛细管电泳法测得β-环糊精与芦荟大黄素在pH=9.7、浓度为0.015 mol/L的硼砂缓冲溶液中的包合反应平衡常数为27.5 L/mol. 由于芦荟大黄素具有强疏水性,故其与环糊精的结合力应属于疏水作用力.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.