乳液聚合法制备剥离型PS/MMT纳米复合材料

以阳离子表面活性剂十八烷基三甲基氯化铵(OTAC)和烯丙基十八烷基二甲基氯化铵(ATAC)为插层处理剂改性蒙脱土(MMT),原位乳液聚合分别制备了PS/C18MMT和PS/AC18MMT两种纳米复合材料.XRD和TEM分析表明,MMT均被剥离成单个或几个片层无规的分散在PS基体中,TGA分析表明,MMT的加入提高了材料的耐热性能,当PS基体与有机化处理的MMT片层发生一定的化学连接后,PS/AC18MMT纳米复合材料表现出更好的耐热性能.动态力学分析表明,MMT的加入提高了PS的玻璃态储能模量,降低了材料的动态损耗;PS/AC18MMT纳米复合材料的玻璃化温度较PS有所提高,而PS/C18MMT的玻璃化温度与PS相比略有降低.     

原位聚合制备聚乙烯/蒙脱土(MMT)纳米复合材料的研究

利用MgCl₂在醇中溶解和蒙脱土(MMT)在醇中层间膨胀的特性,制备了MgCl₂/TiC_l4负载于MMT层间的MMT/MgCl₂/TiC_l4催化剂,并通过原位聚合合成了聚乙烯/蒙脱土纳米复合材料.经广角X射线衍射(WAXD)和透射电子显微镜(TEM)分析表明,蒙脱土片层在乙烯聚合过程中发生了层间剥离,以单片层或几片层共存的形式无规地分散于聚乙烯基质中.与分子量相近的纯聚乙烯相比,极低的蒙脱土含量(质量分数<1%)能使复合材料的屈服强度、拉伸强度和拉伸模量有很大提高.复合材料中蒙脱土片层以纳米尺寸在聚乙烯基质中的良好分布和对聚乙烯分子链运动的限制作用是力学性能提高的主要因素.     

纳米SiO_2粒子锚固偶氮引发剂及接枝聚甲基丙烯酸甲酯

对纳米SiO2 粒子锚固偶氮引发剂 ,进而引发甲基丙烯酸甲酯聚合而制备聚甲基丙烯酸甲酯(PMMA) 纳米SiO2 复合粒子进行了研究 .纳米SiO2 先用环氧型硅烷偶联剂处理 ,再与偶氮二氰基戊酸发生缩合反应而锚固上偶氮引发剂 ,通过差示扫描量热和元素分析证明了引发剂在纳米SiO2 表面的锚固 .通过改性纳米SiO2 存在下MMA的乳液聚合 ,制备得到了接枝率为 2 3 2 %、接枝效率为 36 1%的PMMA 纳米SiO2 复合粒子 .经乳液聚合后 ,纳米SiO2 粒子团聚程度减小 ,在水相中分散稳定 .     

原位聚合法制备超疏水的聚乙烯纳米复合材料

采用一种新方法将Ziegler-Natta催化剂组分TiCl4和MgCl2负载到蒙脱土(MMT)的层间,制备了TiCl4/MgCl2/MMT插层型催化剂.利用Ziegler-Natta催化剂特有的"形态复制效应",通过乙烯原位聚合制备出了表面具有花瓣状形态的聚乙烯纳米复合材料.这种聚乙烯纳米复合材料的表面与水的接触角达到(152.2±0.8)°,呈现超疏水性质.     

辐照法制备的醋酸乙烯酯/蒙脱土纳米复合材料与HDPE和PA6共混物的研究

利用γ射线辐射引发醋酸乙烯酯(VAc)在蒙脱土(MMT)中的原位插层聚合,X射线衍射测试与透射电子显微镜观察结果表明,PVAc/MMT复合材料为纳米复合材料.其与HDPE和PA6的共混物的扫描电镜测试结果表明,PVAc-MMT纳米复合物以微胶囊的形式存在于PVAc-MMT/HDPE/PA6共混物中,均匀分散的PVAc-MMT纳米复合物改变了复合材料的相结构.热失重测试结果显示,PVAc-MMT/HDPE/PA6的起始分解温度明显高于PVAc/HDPE/PA6,热失重过程差异较大,MMT纳米粒子的存在改变了材料的结构,使材料热性能得到了改善.在PVAc-MMT/HDPE/PA6共混物中,PVAc-MMT具有增强与增韧作用.     

接枝聚苯乙烯/多壁碳纳米管纳米复合材料制备及合成机理

通过原位悬浮聚合的方法, 以过氧化苯甲酰(BPO)做引发剂, 制备了聚苯乙烯/多壁碳纳米管(MWNT-g-PS)纳米复合材料, 复合材料在水和乙醇中均表现出良好的分散性及稳定性. 通过高倍透射电镜(HRTEM)、场发射扫描电镜(FESEM)分析, 多壁碳纳米管上包覆有1～3 nm的聚苯乙烯膜, 并分布有半径从几十纳米到几百纳米不等的聚苯乙烯微球. 通过傅立叶变换红外光谱(FTIR)、拉曼光谱(Raman spectroscopy)、X光电子能谱(XPS)和热重分析(TGA)对复合材料进行分析, 结果表明, 自由基将多壁碳纳米管表面π键打开, 形成一种新的自由基, 引发聚苯乙烯的自由基聚合, 形成了接枝聚苯乙烯/多壁碳纳米管纳米复合材料.     

尼龙6/石墨纳米导电复合材料的制备与性能

通过原位插层聚合制备了尼龙 6 /石墨纳米导电复合材料 ,其室温导电渗滤阈值为 =0 75vol% ,远远低于常规导电粒子填充的聚合物复合材料 .当石墨体积分数为 2 0vol%时 ,室温电导率可达 10 -4 S/cm .透射电镜研究表明 :由于石墨经高温膨胀后其片层被剥离导致了片状石墨粒子具有巨大的径厚比 ,经原位插层聚合其片层厚度进一步被剥离为几十个纳米 ,同时原位插层聚合使得石墨粒子能够均匀分散在尼龙 6基体中 ,因而导致了该导电复合材料的低渗滤阈值和高导电性能 .     

纳米SiO_2锚固光敏基团引发MMA光接枝聚合研究

对纳米SiO2进行了锚固光引发剂的表面修饰,进而引发甲基丙烯酸甲脂(MMA)光接枝聚合制备有机/无机复合粒子.纳米SiO2粒子首先用氯化亚砜进行表面氯化,再与光引发剂2-羟基-4-(2-羟基乙氧基)-2-甲基苯丙酮(Irgacure2959)反应从而锚固上光引发剂.通过紫外光引发MMA在经过修饰过的纳米SiO2表面上进行表面光接枝聚合.采用IR、TGA和TEM等方法表征了接枝前后纳米粒子的变化,证明了表面接枝物的存在,并研究了不同反应条件对单体转化率、接枝率和接枝效率的影响.研究结果表明,搅拌对接枝过程的影响比较显著.TGA结果显示未搅拌聚合时接枝率只能达到比较小的程度,而在搅拌条件下180min内MMA的接枝率可达到110%.     

通过正离子聚合原位制备聚谷氨酸苄酯-g-(聚四氢呋喃-b- 聚异丁烯)/银纳米复合材料及其性能研究

采用烯丙基溴官能化聚异丁烯/高氯酸银体系引发四氢呋喃活性正离子聚合制备聚谷氨酸苄酯-g-(聚四氢呋喃-b-聚异丁烯)/银纳米复合材料(PBLG-g-(PTHF-b-PIB)/Ag).研究接枝密度对该纳米复合材料表面组成、形貌及自组装行为的影响,进一步探究纳米复合材料中银的含量、分布、晶型及存在形态,以布洛芬(IBU)作为模拟药物,研究接枝共聚物中接枝密度和平均支链长度对纳米复合材料载药释药行为的影响,通过抑菌圈法和MTT法研究纳米复合材料的抗菌性和细胞毒性.结果表明:通过烯丙基溴官能化聚异丁烯大分子引发四氢呋喃活性正离子开环聚合,可以原位制备不同接枝密度和不同平均支链长度的PBLG-g-(PTHF-b-PIB)/Ag纳米复合材料,其中银的质量含量在0.25%~3.9%之间,与其理论含量基本相吻合,银颗粒以聚集体形态存在,尺寸为5~10 nm,晶型为面心立方结构;该纳米复合材料在四氢呋喃/正己烷(4/1,V/V)混合介质中自组装形成胶束,胶束数目随接枝密度增加而减少,但尺寸增大;随接枝共聚物中接枝密度和纳米银含量增加,纳米复合材料的疏水性增加;随接枝共聚物中接枝密度增加,纳米复合材料表面形貌可由球形结构逐渐转化为双连续相结构;纳米复合材料的载药微球可以通过接枝共聚物中主链PBLG的空心螺旋结构、酰胺键及PTHF支链的醚键结构显示三重载药特性,载药量和累积释药量均随着接枝共聚物中接枝密度或PTHF链段长度增加而增加,且在37oC下的释药率是25oC下释药率的3倍左右.该纳米复合材料的抗菌性能随纳米银含量增加而增加,当纳米银含量为1.48%时,该纳米复合材料1周后细胞存活率为97.7%,即无细胞毒性.     

漆酚钛聚合物/蒙脱土纳米复合材料的制备、结构与性能

用溶液插层聚合方法制备漆酚钛聚合物/蒙脱土纳米复合材料(PUTi/OMMT),并用XRD、TEM和TG等对其结构、性能进行测试与表征.XRD结果表明,通过溶液插层,PUTi分子链进入了OMMT片层间,从而使片层间距增大.TEM观察表明OMMT片层在PUTi聚合物中基本达到纳米级分散.与PUTi相比,PUTi/OMMT纳米复合材料具有更好的耐热性能和抗紫外光性能.     

聚苯乙烯/蒙脱土纳米复合材料的制备及结构研究

以可与苯乙烯发生共聚的阳离子表面活性剂乙烯苄基二甲基十八烷基氯化铵(VOAC)为插层处理剂改性蒙脱土(VC18-MMT),有机蒙脱土在超声波强剪切作用以及乳化剂作用下预分散在乳化剂溶液中,然后引入苯乙烯单体进行原位乳液聚合制备聚苯乙烯/蒙脱土纳米复合材料.采用XRD和TEM对纳米复合材料的结构进行了表征.结果表明,绝大多数的蒙脱土被剥离成单个片层均匀的分散在聚合物基体中;动态力学分析表明,纳米复合材料的储能模量和玻璃化温度均有所增加,而动态损耗有所降低;接枝在蒙脱土片层上的聚合物通过与锂离子进行阳离子交换反应提取下来,采用GPC和NMR对接枝聚合物的结构进行了表征,结果表明,接枝聚合物是较基体分子量低且分布很宽的苯乙烯和乙烯苄基二甲基十八烷基氯化铵的共聚物,计算表明每一个共聚物分子链上平均含有大约25个乙烯苄基二甲基十八烷基氯化铵分子.     

聚苯胺/蒙脱土纳米复合材料的制备及吸波性能研究

以十二烷基苯磺酸(DBSA)作为乳化剂和掺杂剂,通过乳液聚合的方法制备了DBSA掺杂聚苯胺/蒙脱土(PANI-DBSA/MMT)纳米复合物,并对其微波吸收特性进行了研究.通过X射线衍射(XRD)、傅立叶红外(FT-IR)和四探针测试仪对复合物进行了初步表征.结果表明,PANI-DBSA/MMT复合物中MMT层间距离明显扩大,纳米复合物中的PANI以emeraldine盐的形式存在,是一种典型的插层型纳米复合物.利用HP8722ES矢量网络分析仪测量了2 mm厚、PANI-DBSA/MMT含量为50 wt%的试样在2.0~18 GHz的复介电常数和复磁导率,经计算得到以反射损耗表示的微波吸收曲线,发现PANI-DBSA/MMT纳米复合物在9.1~12.5 GHz范围内反射损耗小于-10 dB,在11 GHz处存在的最大反射损耗为-15.8 dB.     

Synthesis and Rheology of Intercalated Polystyrene/Na+‐Montmorillonite Nanocomposites

Polystyrene (PS)/clay nanocomposites were synthesized by the emulsion polymerization of styrene in the presence of sodium ion‐exchanged montmorillonite (Na⁺‐MMT), demonstrating that the strongly hydrophobic PS was intercalated into the hydrophilic silicate layers. The nanocomposites were examined by means of X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis. The rheological properties of the PS/Na⁺‐MMT nanocomposites were also studied to exhibit more pronounced shear thinning behavior with increasing clay content.     

辐照法制备PVAc/蒙脱土纳米复合材料及其表征

蒙脱土有机化后 ,片层结构间距离增大 ,对有机物的亲和性有所增强 .采用VAc单体渗入有机化蒙脱土层间 .经γ 射线辐照引发原位插层聚合 ,使蒙脱土片层结构发生剥离 ,形成无机 有机纳米复合材料 .并用X衍射、红外光谱、扫描电镜以及透射电镜等现代测试手段对复合材料进行了表征     

Exfoliated high-impact polystyrene/MMT nanocomposites prepared using anchored cationic radical initiator-MMT hybrid

High-impact polystyrene (HIPS)/montmorillonite (MMT) nanocomposites were prepared via in-situ polymerization of styrene in the presence of polybutadiene, using intercalated cationic radical initiator-MMT hybrid. Incomplete exfoliation of the silicate layers in the HIPS nanocomposites was observed when a bulk polymerization was employed. On the other hand, the silicate layers were efficiently exfoliated in the PS matrix during a solution polymerization, due to the low extra-gallery viscosity, which can facilitate the diffusion of styrene monomers into the clay layers. The resulting exfoliated HIPS/MMT nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, thermogravimetric analysis, particle size analysis, gel permeation chromatography, and dynamic mechanical analysis. The nanocomposites exhibited significant improvement in thermal and mechanical properties. For example, about 50% improvement in Young’s modulus was achieved with 5 wt% of clay, compared to the unmodified polymer counterpart.     

Synthesis of poly(methyl methacrylate) nanocomposites via emulsion polymerization using a zwitterionic surfactant

The synthesis of nanocomposites via emulsion polymerization was investigated using methyl methacrylate (MMA) monomer, 10 wt % montmorillonite (MMT) clay, and a zwitterionic surfactant octadecyl dimethyl betaine (C18DMB). The particle size of the diluted polymer emulsion was about 550 nm, as determined by light scattering, while the sample without clay had a diameter of about 350 nm. The increase in the droplet size suggests that clay was present in the emulsion droplets. X-ray diffraction indicated no peak in the nanocomposites. Transmission electron microscopy showed that emulsion polymerization of MMA in the presence of C18DMB and MMT formed partially exfoliated nanocomposites. Differential scanning calorimetry showed an increase of 18 degrees C in the glass transition temperature (Tg) of the nanocomposites. A dynamic mechanical thermal analyzer also verified a similar Tg increase, 16 degrees C, for the partially exfoliated nanocomposites over poly(methyl methacrylate) (PMMA). Thermogravimetric analysis indicated a 37 degrees C increase in the decomposition temperature for a 20 wt % loss. A PMMA nanocomposite with 10 wt % C18DMB-MMT was also synthesized via in situ polymerization. This nanocomposite was intercalated and had a Tg 10 degrees lower than the emulsion nanocomposite. The storage modulus of the partially exfoliated emulsion nanocomposite was superior to the intercalated structure at higher temperatures and to the pure polymer. The rubbery plateau modulus was over 30 times higher for the emulsion product versus pure PMMA. The emulsion technique produced nanocomposites of the highest molecular weight with a bimodal distribution. This reinstates that exfoliated structures have enhanced thermal and mechanical properties over intercalated hybrids.     

Polymer-clay nanocomposites: chemical grafting of polystyrene onto Cloisite 20A

An account of the experiments on preparing polystyrene(PS) nanocomposites through grafting the polymer onto organophilic montmorillonite is reported.Cloisite 20A was reacted with vinyltrichlorosilane to replace the edge hydroxyl groups of the clay with a vinyl moiety.Because the reaction may liberate HC1,it was performed in the presence of sodium hydrogencarbonate to prevent the exchange of quaternary alkylammonium cations with H~+ ions.Only the silanol groups on the edge of the clay react with vinyltrichlorosilane.The radical polymerization of the product with styrene as a vinyl monomer leads to chemical grafting of PS onto the montmorillonite surface.The homopolymer formed during polymerization was separated from the grafted organoclay by Soxhlet extraction.Chemical grafting of the polymer onto Cloisite 20A was confirmed by infrared spectroscopy.The prepared nanocomposite materials and the grafted nano-particles were studied by XRD.Exfoliated nanocomposites may be obtained for 0.5 wt%-l wt%clay content.The nanocomposites were studied by thermogravimertic analysis(TGA) dynamic thermal analysis(DTA) and dynamic mechanical analysis (DMTA).     

Poly(styrene‐b‐tetrahydrofuran)/clay nanocomposites by mechanistic transformation

Synthesis of poly(styrene‐block‐tetrahydrofuran) (PSt‐b‐PTHF) block copolymer on the surfaces of intercalated and exfoliated silicate (clay) layers by mechanistic transformation was described. First, the polystyrene/montmorillonite (PSt/MMT) nanocomposite was synthesized by in situ atom transfer radical polymerization (ATRP) from initiator moieties immobilized within the silicate galleries of the clay particles. Transmission electron microscopy (TEM) analysis showed the existence of both intercalated and exfoliated structures in the nanocomposite. Then, the PSt‐b‐PTHF/MMT nanocomposite was prepared by mechanistic transformation from ATRP to cationic ring opening polymerization (CROP). The TGA thermogram of the PSt‐b‐PTHF/MMT nanocomposite has two decomposition stages corresponding to PTHF and PSt segments. All nanocomposites exhibit enhanced thermal stabilities compared with the virgin polymer segments. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2190–2197, 2009     

苯乙烯在阴离子型聚氨酯纳米水分散液中聚合过程的研究

采用自乳化法制备出阴离子聚氨酯纳米水分散液,以其作为乳化剂使苯乙烯单体在其中进行聚合,制备出不同聚苯乙烯与聚氨酯质量比的阴离子型PS/PU纳米复合物水分散液;对苯乙烯单体的聚合过程进行了研究;采用光子相关谱仪和透射电镜对其微观结构、粒径及其分布进行了测试,结果表明,该方法能够制备出稳定的具有核壳结构的PS/PU纳米复合物水分散液,但当苯乙烯单体浓度增大到一定程度(PS/PU质量比为50∶100)时,粒子不稳定而发生聚集.