纳米SiO_2粒子锚固偶氮引发剂及接枝聚甲基丙烯酸甲酯

对纳米SiO2 粒子锚固偶氮引发剂 ,进而引发甲基丙烯酸甲酯聚合而制备聚甲基丙烯酸甲酯(PMMA) 纳米SiO2 复合粒子进行了研究 .纳米SiO2 先用环氧型硅烷偶联剂处理 ,再与偶氮二氰基戊酸发生缩合反应而锚固上偶氮引发剂 ,通过差示扫描量热和元素分析证明了引发剂在纳米SiO2 表面的锚固 .通过改性纳米SiO2 存在下MMA的乳液聚合 ,制备得到了接枝率为 2 3 2 %、接枝效率为 36 1%的PMMA 纳米SiO2 复合粒子 .经乳液聚合后 ,纳米SiO2 粒子团聚程度减小 ,在水相中分散稳定 .     

纳米SiO_2粒子表面静电吸附引发剂的活性研究

引发剂2,2′-偶氮二(2-脒基丙烷)二氢氯化物(AIBA)可通过静电作用而高效稳定地吸附到在弱碱性水相中均匀稳定分散的纳米SiO2粒子表面.对这些吸附引发剂的热分解行为、在纳米SiO2粒子表面原位引发甲基丙烯酸甲酯(MMA)乳液聚合的动力学和纳米SiO2粒子表面的聚合锚固情况进行了研究.发现非吸附和吸附引发剂的热分解活化能分别为148.5kJ/mol和124.5kJ/mol,70℃时半衰期分别为12.6h和5.2h,说明在相同状态下静电吸附引发剂具有比非吸附引发剂更高的活性,因而在原位乳液聚合中表现出比常规乳液聚合更短的诱导期和更高的聚合速率.更关键的是,具有较高活性的吸附引发剂高效稳定地吸附在SiO2粒子表面,可以使聚合反应总是优先发生于纳米SiO2粒子表面,从而可以更好地促进单体在纳米SiO2粒子表面的锚固,最终有效提高无机/有机相间的复合程度.     

通过RAFT聚合制备SiO2/接枝共聚物纳米杂化粒子

以二氧化硅(SiO2)纳米粒子表面键接的二硫代苯甲酸酯作为可逆加成-断裂-链转移(RAFT)聚合反应的链转移剂, 在室温下引发苯乙烯和马来酸酐进行表面RAFT交替共聚反应, 制得了SiO2/苯乙烯-alt-马来酸酐杂化材料. 通过聚氧化乙烯(PEO)的羟基与马来酸酐的酯化反应, 将PEO接枝到SiO2纳米粒子的表面, 增加了硅粒子的生物相容性. 用FTIR, TGA和TEM对杂化材料的结构、组成和形貌进行了表征.     

巯基-内酰胺引发活性自由基接枝聚合制备凹凸棒土/聚苯乙烯杂化粒子的研究

通过γ-巯丙基三甲氧基硅烷(MTS)与凹凸棒土(ATP)表面上的羟基发生脱醇反应,制得表面巯基化的改性粒子ATP-MTS;基于“引发剂转移终止剂”(iniferter)原理,构建巯基-己内酰胺(thiol-caprolactam)双组份引发剂转移终止体系引发苯乙烯活性自由基接枝聚合,制得表面接枝聚苯乙烯的杂化粒子ATP-g-PS.通过红外光谱(FTIR)、X射线光电子能谱(XPS)、热失重分析(TGA)、高分辨率透射电镜(TEM)等方法对杂化粒子ATP-g-PS的结构、组成、形貌进行了表征.结果表明,巯基-己内酰胺双组份引发剂转移终止体系可有效实现苯乙烯的活性接枝聚合,聚苯乙烯成功接枝到改性粒子ATP-MTS表面;模拟实验表明聚合体系呈现活性聚合的特征,单体转化率和PS的分子量均随反应时间的增加而增大,TGA结果表明制得的杂化粒子表面PS接枝率为33.3％.     

表面引发接枝聚合法制备凹凸棒土/聚甲基丙烯酸甲酯杂化粒子的研究

将γ-氨丙基三乙氧基硅烷(APTES)接枝到凹凸棒土(AT)表面,制得表面键合伯氨基的改性粒子AT-APTES;通过AT-APTES表面的伯氨基和过硫酸铵(APS)构成氧化-还原引发体系,采用无皂乳液法实现甲基丙烯酸甲酯(MMA)在AT表面接枝聚合,制得最高接枝率为29.4%的杂化粒子AT-g-PMMA;采用红外光谱(FTIR)、拉曼光谱(Raman)、透射电镜(TEM)以及热失重分析(TGA)等方法对杂化粒子AT-g-PMMA进行了表征;研究了主要配方及工艺条件对表面引发接枝聚合接枝率的影响.结果表明,伯氨基-过硫酸铵引发体系可以有效引发MMA在AT表面接枝聚合,由于引发点位于AT表面,故接枝率较高.本研究体系适宜的温度为65℃,单体MMA用量为水质量的6%,APS用量为单体质量的1%,此工艺条件下可有效减小均聚反应对接枝聚合反应的影响.先接枝到AT表面的聚合物对后续的接枝聚合反应产生抑制作用,接枝率越高,抑制作用越大.     

RAFT链转移剂存在下凹凸棒土表面甲基丙烯酸甲酯接枝聚合

将γ-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPS)接枝到凹凸棒土(AT)表面,制得表面带有可聚合碳碳双键的改性粒子AT-MPS;以二硫代苯甲酸氰基异丙酯(CPDB)为链转移剂,采用可逆加成断裂链转移(RAFT)聚合技术,在AT表面进行甲基丙烯酸甲酯(MMA)接枝聚合.通过红外(FTIR)、热失重(TGA)等方法进行了表征,考察了引发剂以及RAFT链转移剂用量对聚合反应动力学和AT表面接枝聚合接枝率的影响.结果表明,PMMA通过RAFT聚合成功接枝在AT表面;基于RAFT过程的接枝聚合比传统自由基接枝聚合具有更长的反应时间和较高的接枝率.本体系相对适宜条件:温度为70℃,[MMA]/[CPDB]/[AIBN]为400/1/0.5.此条件下聚合反应具有很好的可控性,溶液中的聚合物分子量分布指数为1.2~1.3,AT表面PMMA接枝率为16.33%.引发剂和RAFT链转移剂用量过大均会造成接枝率降低.     

表面引发接枝聚合法制备接枝微粒PHEMA/SiO2及其8-羟基喹啉功能化转变研究

通过用表面引发接枝聚合和高分子反应制备8-羟基喹啉型复合螯合微粒.首先使用γ-氨丙基三甲氧基硅烷(AMPS)对微米级硅胶微粒进行表面改性,制得改性微粒AMPS-SiO2;使改性微粒AMPS-SiO2表面的氨基与溶液中的过硫酸盐构成氧化-还原引发体系,实施了甲基丙烯酸羟乙酯(HEMA)在硅胶微粒表面的高效引发接枝聚合,制得了接枝微粒PHEMA/SiO2.又以5-氯甲基-8-羟基喹啉(CHQ)为试剂,使接枝的PHEMA发生大分子反应,实现了接枝微粒PHEMA/SiO2的8-羟基喹啉功能化转变,制得了复合微粒HQ-PHEMA/SiO2.采用多种手段对两种微粒进行了表征,重点研究了氨基-过硫酸盐表面引发接枝体系的接枝聚合机理,并研究了CHQ与接枝PHEMA的醇羟基之间取代反应的机理,还初步考察了功能微粒HQ-PHEMA/SiO2对重金属离子的螯合吸附性能.研究结果表明,氨基-过硫酸盐表面引发接枝聚合体系具有很高的引发活性,在室温(30℃)即可制得高接枝密度(40 g/100g)的接枝微粒PHEMA/SiO2;CHQ与接枝PHEMA的醇羟基之间的取代反应遵循SN1的反应历程,使用强极性溶剂有利于反应的进行.微粒HQ-PHEMA/SiO2对重金属离子呈现很强的螯合吸附能力,是一种功能复合微粒.     

SiO2交联剂交联MMA聚合制备PMMA/SiO2纳米复合材料

用SiO2交联剂(SiO2HPA)交联甲基丙烯酸甲酯(MMA)自由基聚合制备PMMA SiO2纳米复合材料。采用两步法将可聚合乙烯基单体以化学键的形式键接到SiO2表面合成SiO2交联剂,首先利用过量的甲苯2,4二异氰酸酯(TDI)对SiO2纳米粒子表面进行化学修饰合成出表面带有高反应活性NCO基团的功能化SiO2粒子(SiO2TDI),SiO2TDI与丙烯酸羟丙酯(HPA)反应合成SiO2交联剂。系统研究了MMA单体与SiO2交联剂投料比及聚合时间对聚合反应的影响。此外,利用红外光谱(FT IR)、DSC、TGA、可见光光谱仪等实验手段对纳米复合材料进行了表征分析。结果表明,纳米SiO2粒子在复合材料中起着物理交联点和化学交联点作用,复合材料玻璃化转变温度(Tg)明显地高于其纯PMMA的玻璃化转变温度,随着纳米SiO2粒子含量的增加,复合材料玻璃化温度升高,而透明度明显降低。     

由铜-胺氧化还原引发反应一步法简便制备TiO_2表面接枝聚甲基丙烯酸甲酯纳米杂化粒子

提出并验证了一种通过普通自由基聚合在纳米TiO2表面接枝聚甲基丙烯酸甲酯的简单方法.通过在纳米TiO2粒子表面引入伯胺分子层(纳米TiO2-NH2粒子),利用Cu2+-胺氧化还原体系实现了CuSO4催化纳米TiO2-NH2粒子表面引发甲基丙烯酸甲酯(MMA)的自由基接枝聚合,从而一步得到表面固定有聚甲基丙烯酸甲酯链的纳米TiO2杂化粒子(纳米TiO2-PMMA杂化粒子).红外光谱、热失重分析与电镜的结果都表明PMMA已经被接枝到纳米TiO2粒子表面,且接枝率随着聚合时间的延长而逐渐增大,PMMA链的引入有助于降低纳米TiO2粒子微球的团聚程度、增强与有机溶剂分子的范德华力,从而提高分散稳定性.反应溶液中没有游离均聚物形成.     

纳米SiO_2表面基团在MMA原位本体聚合中的阻缓聚作用

分别以3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPS)和辛基三甲氧基硅烷(OTMS)为活性和惰性硅烷的代表,对SiO2进行不同锚固密度的表面修饰,并以改性SiO2的甲基丙烯酸甲酯(MMA)单体分散液为原料,通过原位本体聚合制得一系列SiO2含量不同的高分散性SiO2/PMMA复合材料.考察SiO2表面基团活性程度和SiO2含量对聚合反应动力学、基体聚合物分子量以及复合材料硬度的影响,探究修饰状态不同SiO2在本体自由基聚合中的作用机制.发现SiO2表面硅羟基及其锚固MPS的活性双键会对聚合反应起阻缓聚作用,进而会显著降低基体聚合物的分子量及复合材料的硬度.而惰性硅烷OTMS对SiO2表面的锚固则会消耗SiO2表面硅羟基、并屏蔽其影响,因而随着OTMS锚固密度的提高,基体分子量和复合材料硬度均会随之提高,特别是当表面修饰达到饱和状态时,SiO2的阻缓聚作用已可忽略.     

表面自由基链转移反应制备聚合物修饰的固定相

 利用巯丙基修饰硅胶的自由基链转移反应 ,在硅胶表面原位引发自由基聚合 ,制备了聚甲基丙烯酸甲酯修饰的反相高效液相固定相。通过红外吸收光谱 (FTIR)、拉曼光谱、热失重 (TGA)和元素分析对该固定相进行了表征。该固定相对含氧芳香化合物、多环芳烃等均有良好的分离能力。     

Preparation of poly(methyl methacrylate) grafted hydroxyapatite nanoparticles via reverse ATRP

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technical was successfully employed to modify hydroxyapatite (HAP) nanoparticles with poly(methyl methacrylate) (PMMA). The peroxide initiator moiety for reverse ATRP was covalently attached to the HAP surface through the surface hydroxyl groups. Reverse ATRP of methyl methacrylate (MMA) from the initiator-functionalized HAP was carried out, and the end bromide groups of grafted PMMA initiated ATRP of MMA subsequently. Fourier transformation infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle structure. The grafted PMMA gave HAP nanoparticles excellent dispersibility in MMA monomer. As the amount of grafted PMMA increased, the dispersibility of surface-grafted HAP and the compressive strength of HAP/PMMA composites were improved.     

高分散性SiO2/PMMA复合材料的制备与表征——纳米SiO2在MMA中的分散

用硅烷偶联剂3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPS)对分散于乙醇中的纳米SiO2进行偶联改性,再通过介质置换和原位本体聚合制得SiO2/甲基丙烯酸甲酯(MMA)单体分散液和SiO2/PMMA复合材料.红外光谱分析(FTIR)和热重分析(TG)结合洗提实验考察了SiO2表面MPS的偶联率和偶联效率,透射电镜(TEM...     

Photografting of vinyl polymers onto ultrafine inorganic particles: Photopolymerization of vinyl monomers initiated by AZO groups introduced onto these surfaces

The photografting of polymers onto ultrafine inorganic particles, such as silica and titanium oxide, initiated by azo groups introduced onto these surfaces was investigated. The introduction of azo groups onto the particles was achieved by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with surface isocyanate groups, which were introduced by the treatment with tolylene 2,4-diisocyanate. It was found that the photopolymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and N-vinylcarbazole, is initiated by ultrafine particles having azo groups. The corresponding polymers were effectively grafted onto these surfaces through the propagation of the polymer from the surface radicals formed by the photodecomposition of the azo groups: e.g., the percentage of grafting of PMMA and polystyrene onto silica was reached to 112 and 176%, respectively. The percentage of grafting onto silica in the graft polymerization initiated by photodecomposition of surface azo groups was much larger than that initiated by thermal decomposition. Polymer-grafted ultrafine particles thus obtained gave a stable colloidal dispersion in good solvents for the grafted chain. © 1994 John Wiley & Sons, Inc.     

Effects of methyl methacrylate grafting and in situ silica particle formation on the morphology and mechanical properties of natural rubber composite films

The effects of methyl methacrylate (MMA) grafting and in situ formation of silica particles on the morphology and mechanical properties of natural rubber latex (NRL) were investigated. MMA grafting on NRL was carried out using cumyl hydroxy peroxide/tetraethylene pentamine (CHPO/TEPA) as a redox initiator couple. The grafting efficiency of the grafted NR was determined by solvent extractions and the grafted NRL was then mixed with tetraethoxysilane (TEOS), a precursor of silica, coated by adherence to a glass surface to form a film and cured at 80°C. The resultant products were characterized by FT‐IR and transmission electron microscopy. The influence of varying the MMA monomer weight ratio on the surface morphology of the composites was investigated by scanning electron and atomic force microscopy. The PMMA (poly MMA) grafted NRL particles were obtained as a core/shell structure from which the NR particles were the core seed and PMMA was a shell layer. The silane was converted into silica particles by a sol–gel process which was induced during film drying at 80°C. The silica particles were fairly evenly distributed in the ungrafted NR matrix but were agglomerated in the grafted NR matrix. The root‐mean‐square roughness increased with an increasing weight ratio of MMA in the rubber. The in situ silica particles in the grafted NR matrix slightly increased both the modulus and the tear strength of the composite film. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation and characterization of poly(methyl methacrylate)/titanium oxide composite particles

Before polymerization, the introduction of double bonds onto the surface of the TiO₂ particles was achieved by the treatment of the TiO₂ particles with the silane-coupling agent. Via in-situ emulsion polymerization, the poly(methyl methacrylate) (PMMA)/titanium oxide (TiO₂) composite particles were prepared by graft polymerization of MMA from the surface of the modified TiO₂ particles. The structure of the obtained PMMA/TiO₂ composite particles was characterized using fourier transform infrared spectra (FT-IR), thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC) and size excluding chromatography (SEC). The morphology of the obtained PMMA/TiO₂ composite particles was observed by transmission electron microscope (TEM). The results of FT-IR and TGA measurements show that PMMA is successfully grafted from the surface of the TiO₂ particles and that the percentage of grafting and the grafting efficiency can reach 208.3% and 96.6%, respectively. At the same time, the TGA and DSC measurements indicate an enhancement of thermal stability. TEM images demonstrate a better dispersion of the TiO₂ particles in the composite latex. In addition, UV-visible absorption measurements show that the PMMA/TiO₂ composite particles can absorb over 95% UV light at 210–400 nm wavelength.     

Graft polymerization of methyl methacrylate from silica initiated by peroxide groups introduced onto the surface

The surface grafting onto ultrafine silica by the radical polymerization of methyl methacrylate (MMA) initiated by peroxide groups introduced onto the surface was investigated. The introduction of peroxide groups onto the silica surface was achieved by the reaction of hydrogen peroxide with chlorosilyl groups, which were introduced by the treatment of silica with thionyl chloride. The content of diisopropylbenzene peroxide and tert-butyl peroxide groups introduced onto the silica according to the above method was determined to be 0.11 and 0.08 mmol/g, respectively. It was found that the polymerization of MMA is initiated by silica having these peroxide groups. In the polymerization, polyMMA was grafted onto silica surface: the percentage of grafting reached about 70%. Therefore, it was concluded that the polymerization of MMA is initiated by surface radicals formed by the decomposition of peroxide groups on silica and polyMMA is grafted through the propagation from the surface. During the polymerization, ungrafted polyMMA was also formed because of the formation of initiator fragments by the decomposition of peroxide groups: the grafting efficiency of the graft polymerization was 30–40%. PolyMMA-grafted silica produced a stable colloidal dispersion in organic solvents for polyMMA. © 1992 John Wiley & Sons, Inc.     

Surface modification of silica nanoparticles by UV-induced graft polymerization of methyl methacrylate

In this study we modified the surface of silica nanoparticles with methyl methacrylate by UV-induced graft polymerization. It is a surface-initiated polymerization reaction induced by ultraviolet irradiation. The resulting organic-inorganic nanocomposites were near-monodisperse and fabricated without homopolymerization of the monomer. Substantial increase in mean particle size was observed by SEM image analysis after UV-induced grafting of methyl methacrylate onto pure silica particles. FT-Raman spectroscopy and X-ray photoelectron spectroscopy studies of these materials revealed the successful grafting of methyl methacrylate onto the silica surface. The formation of a covalent bond between the grafted PMMA chains and silica surface was indicated by FT-Raman spectra. Thermogravimetric analysis of the PMMA-grafted silica particles indicated the polymer contents in good agreement with SEM photographs.     

甲基丙烯酸甲酯/纳米SiO_2粒子分散液的细乳化和细乳液聚合

对包含纳米SiO2粒子的甲基丙烯酸甲酯(MMA)的细乳化和细乳液聚合行为进行了研究.发现在超声细乳化过程中,90%以上的分散于MMA相的纳米SiO2粒子将从油相逃逸到水相.采用甲基丙烯酸3-(三甲氧基甲硅烷基)丙酯(MPS)偶联剂处理SiO2粒子,可以增加其表面亲油性,抑止这种逃逸,经测定几乎全部SiO2粒子在超声细乳化后仍稳定停留在细乳化亚微液滴中.通过进一步细乳液聚合,得到了分散稳定、界面清晰的包裹有纳米SiO2粒子的聚甲基丙烯酸甲酯复合粒子乳液.