原位聚合法制备超疏水的聚乙烯纳米复合材料

采用一种新方法将Ziegler-Natta催化剂组分TiCl4和MgCl2负载到蒙脱土(MMT)的层间,制备了TiCl4/MgCl2/MMT插层型催化剂.利用Ziegler-Natta催化剂特有的"形态复制效应",通过乙烯原位聚合制备出了表面具有花瓣状形态的聚乙烯纳米复合材料.这种聚乙烯纳米复合材料的表面与水的接触角达到(152.2±0.8)°,呈现超疏水性质.     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

聚丙烯酰胺/蒙脱土纳米复合物-聚乙烯醇共混膜的制备及其渗透汽化性能

用原位聚合法制备聚丙烯酰胺/蒙脱土(PAM/MMT)纳米复合材料, 通过透射电镜研究了蒙脱土在聚丙烯酰胺基体中的形貌和分布. 结果表明, 蒙脱土以片层结构分布在聚合物基体中. 用超声波分散聚乙烯醇和聚丙烯酰胺-蒙脱土共混铸膜液制得共混膜, 用红外吸收光谱和扫描电镜研究了两者的相互作用和形貌. 考察了共混膜在异丙醇-水混合溶液中的溶胀吸附性能及共混比和蒙脱土含量对膜分离性能的影响, 结果显示, 聚乙烯醇膜中添加适量的蒙脱土纳米粒子可以大大改善膜的分离选择性.     

动态扭振法研究聚甲基丙烯酸甲酯/蒙脱土纳米复合材料的本体插层聚合

用动态扭振法研究热塑性塑料聚甲基丙烯酸甲酯(PMMA)/蒙脱土(MMT)复合体系的本体插层聚合.并试用处理交联体系固化的Flory理论、非平衡态热力学涨落理论和Avrami方程研究PMMA/MMT复合体系的本体插层聚合,求取表观活化能Ea.实验发现,PMMA/MMT插层聚合转化率曲线中后期与热固性树脂的固化曲线极为类似,表明剥离后的蒙脱土片层在复合材料中起到交联点的作用.     

蒙脱土负载型引发剂的制备及在苯乙烯乳液聚合中的应用

通过正离子交换将引发剂AIBA负载在蒙脱土上制得负载型引发剂V50-MMT.进而采用原位乳液聚合方法引发苯乙烯聚合制备PS/MMT纳米复合材料.采用XRD、TGA、DSC、TEM和抽提等方法对负载型引发剂和纳米复合材料进行了表征.结果表明,负载过程中引发剂AIBA进入了MMT的片层之间;聚合过程中介于片层间的引发剂因发生分解一方面产生自由基引发St聚合,另一方面MMT发生了剥离分散;由此法制备的PS/MMT纳米复合材料,MMT片层无规、均匀地分散于PS基体中,片层厚度在几个纳米至十几个纳米之间,长度为几十至几百个纳米不等;大量的PS链段以化学键接枝在MMT的片层上,接枝在MMT片层上的PS的分子量及其分布与游离的PS不同.     

一步法制备蒙脱土-石墨烯协同增强聚乙烯醇复合材料

以蒙脱土(MMT)和石墨烯(rGO)为填料,一步法制备了MMT-rGO/PVA纳米复合材料,并研究了不同MMT/rGO比例对PVA复合膜力学性能的影响.结果表明,剥离的MMT片层能够有效阻止石墨烯在被还原过程中的团聚.MMT-rGO二元填料与PVA间形成氢键,极大地改善了填料与聚合物间的界面结合,能够协同提高PVA复合膜的力学性能.1 wt%MMT-GE(2∶1)/PVA复合材料的拉伸强度和杨氏模量最高,分别为85.1 MPa和1627.8 MPa,比纯PVA分别提高了46%和62%.此方法为制备高性能聚合物复合材料提供了有效的途径.     

聚氨酯弹性体/蒙脱土纳米复合材料的合成与性能

采用聚氨酯本体预聚法 ,利用原位插层聚合合成了聚氨酯 蒙脱土纳米复合材料 .通过X 射线衍射(XRD)和Molau实验研究了蒙脱土在复合材料中的分散情况 .红外分析 (IR)表明随着蒙脱土含量的增加 ,复合材料羰基氢键减少 .动态力学分析 (DMA)以及差热分析 (DSC)结果说明随着蒙脱土含量的增加 ,材料的玻璃化温度降低 .聚氨酯纳米复合材料的拉伸强度和断裂伸长率同时提高 ,表现出较好的力学性能 .     

聚氨酯弹性体/蒙脱土纳米复合材料的合成、结构与性能

采用插层聚合法合成了综合力学性能优异的聚氨酯 蒙脱土纳米复合材料 .X 射线衍射结果表明 ,蒙脱土以平均层间距不小于 4 5nm的宽分布分散在聚氨酯基体中 .加入 7 5wt%左右的蒙脱土 ,复合材料的拉伸强度高于纯PU基体的 2倍 ,断裂伸长率则高于纯PU基体的 4倍以上 .TGA分析表明 ,聚氨酯 蒙脱土纳米复合材料的热稳定性略有提高     

聚苯胺/离子液体/蒙脱土纳米复合材料的制备及其导电性能研究

采用1-羧甲基-3-甲基咪唑氯化盐离子液体对钠化蒙脱土进行插层改性,然后用苯胺的盐酸溶液进行二次插层,以过硫酸铵为氧化剂,盐酸溶液为掺杂剂,使进入离子液体/蒙脱土(CMMIm/MMT)层间的苯胺(An)发生氧化聚合反应,制备了一种具有良好导电性的聚苯胺/离子液体/蒙脱土复合材料(PANI/CMMIm/MMT).用红外光谱、X-射线衍射,热重分析和DSC对样品进行了表征.结果表明当离子液体/蒙脱土用量为7.5%、盐酸浓度为1mol/L、过硫酸铵与苯胺的摩尔比为1∶1、0℃下反应6h时制备的PANI/CMMIm/MMT纳米复合材料电导率最高,达到了0.3S/cm,是相同条件下聚苯胺/钠化蒙脱土纳米复合材料电导率的2.5倍,聚苯胺的7.5倍.     

插层聚合制备聚丙烯/蒙脱土纳米复合材料及其结构性能表征

将插层聚合的概念引入烯烃聚合,制备了聚丙烯／蒙脱土（PP／MMT）纳米复合材料。X射线衍射和TEM分析结果表明,蒙脱土在聚丙烯基体中达到了纳米级的分散,动态力学性能研究结果表明,在高于Tg的温度区域内PP／MMT纳米复合材料的储能模量（E′）成倍增加,加入8％的蒙脱土（MMT）,PP／MMT的E′提高近3倍。PP／MMT的玻璃化转变温度Tg有一定程度的提高,随蒙脱土含量的增加,PP／MMT的热分解温度和热变形温度（HDT）都有大幅度提高。     

SYNTHESIS AND CHARACTERIZATION OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES VIA AN in-situ POLYMERIZATION APPROACH

Polypropylene/montmorillonite (PP/MMT)nanocomposites were prepared by in-situ polymerization using aMMT/MgCl_2/TiCl_4-EB Ziegler-Natta catalyst activated by triethylaluminum(TEA). The enlarged layer spacing of MMT wasconfirmed by X-ray wide angle diffraction (WAXD), demonstrating that MMT were intercalated by the catalyst components.X-ray photoelectron spectrometry (XPS) analysis proved that TiCl_4 was mainly supported on MgCl_2 instead of on the surfaceof MMT The exfoliated structure of MMT layers in the PP matrix of PP/MMT composites was demonstrated by WAXDpatterns and transmission electron microscopy (TEM) observation. The higher glass transition temperature and higher storage modulus of the PP/MMT composites in comparison with pure PP were revealed by dynamic mechanical analysis (DMA).     

辐照法制备PVAc/蒙脱土纳米复合材料及其表征

蒙脱土有机化后 ,片层结构间距离增大 ,对有机物的亲和性有所增强 .采用VAc单体渗入有机化蒙脱土层间 .经γ 射线辐照引发原位插层聚合 ,使蒙脱土片层结构发生剥离 ,形成无机 有机纳米复合材料 .并用X衍射、红外光谱、扫描电镜以及透射电镜等现代测试手段对复合材料进行了表征     

Preparation of thermosetting polyurethane nanocomposites by montmorillonite modified with a novel intercalation agent

A novel thermosetting polyurethane (TSPU)/organic montmorillonite (OMMT) nanocomposite has been synthesized. N‐diamino octadecyl trimethyl ammonium chloride (DODTMAC) was used as an intercalation agent to treat Na⁺‐montmorillonite (MMT) and form a novel kind of OMMT. Fourier transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and thermogravimetric analysis (TGA) data indicated that the MMT was successfully intercalated by this intercalation agent, as evidenced by the fact that the basal spacing of MMT galleries was expanded from 1.5 to 3.2 nm. This OMMT was used to prepare the TSPU nanocomposites. Both the reinforcing and compatibilizing performance of the filler were investigated. Tensile tests showed that the tensile strength of TSPU/OMMT‐4 was the highest, and was about 3.62 times higher than that of the pure TSPU, and also the elongation at break showed an enhancement. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) measurements illustrated that the glass transition temperature of the TSPU/OMMT‐4 nanocomposite was improved from 0.5 to 6.5 °C, which corresponded to the restriction of the soft segments of TSPU. The highest initial and center temperatures of TSPU/OMMT‐4 obtained from TGA were due to the highest retard effect of the TSPU molecular chains. WAXD studies showed that the formation of the nanocomposites in all the cases with the almost disappearance of the peaks corresponding to the basal spacing of MMT. SEM and TEM were used to investigate the morphologies of the TSPU/OMMT‐4 nanocomposite, and demonstrated that the nanocomposite was comprised of a well dispersion of a mixture of intercalated and exfoliated silicate layers throughout the matrix. It was proposed that the nano‐reinforcing effect caused by the well‐dispersed silicate layers might reduce the amount and size of voids and increase the length of the crack‐spreading path during tensile drawing. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 519–531, 2007.     

PREPARATION AND CHARACTERIZATION OF SOY PROTEIN ISOLATE(SPI)/MONTMORILLONITE(MMT) BIONANOCOMPOSITES

 The bionanocomposites of soy protein isolate (SPI)/montmorillonite (MMT) have been prepared successfully via simple melt mixing, in which MMT was used as nanofiller and glycerol was used as plasticizer. Their structures and properties were characterized with X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), thermogravimetric analysis and tensile testing. XRD、TEM and SEM results indicated that the MMT layers could be easily intercalated by the SPI matrix even by simple melt processing. The exfoliated MMT layers were randomly dispersed in the protein matrix as MMT content was low (less than 5 wt%), an incomplete exfoliation was evident from SEM results, and some primary particles were observed as the MMT content was high (from 5 wt% to 9 wt%). A significant improvement of the mechanical strength and thermal stability of SPI/MMT nanocomposites has been achieved. Our work suggests that simple melt processing is an efficient way to prepare SPI/MMT nanocomposites with exfoliated structure.     

Multiple melting and crystallization of nylon‐66/montmorillonite nanocomposites

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with organically modified montmorillonite (MMT). The organic MMT layers were exfoliated in a nylon‐66 matrix as confirmed by wide‐angle X‐ray diffraction (WAXD) and transmission electron microscopy. The presence of MMT layers increased the crystallization temperature of nylon‐66 because of the heterogeneous nucleation of MMT. Multiple melting behavior was observed in the nylon‐66/MMT nanocomposites, and the MMT layers induced the formation of form II spherulites of nylon‐66. The crystallite sizes L₁₀₀ and L₀₁₀ of nylon‐66, determined by WAXD, decreased with an increasing MMT content. High‐temperature WAXD was performed to determine the Brill transition in the nylon‐66/MMT nanocomposites. Polarized optical microscopy demonstrated that the dimension of nylon‐66 spherulites decreased because of the effect of the MMT layers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2861–2869, 2003     

聚对苯二甲酸乙二酯/蒙脱土纳米复合材料的制备和性能

讨论了聚对苯二甲酸乙二醇酯（ＰＥＴ）／层状硅酸盐（蒙脱土）纳米复合材料的制备技术和新材料的结构与性能特征．天然蒙脱土矿物经有机离子修饰剂处理后,参与ＰＥＴ的缩聚反应．ＴＥＭ测定证实蒙脱土在ＰＥＴ中的层厚分布为３０～５０ｎｍ．蒙脱土不影响ＰＥＴ的分子量及其分布．利用ＤＳＣ、ＷＡＸＤ、ＳＡＬＳ和偏光显微镜测定了ＰＥＴ／蒙脱土的结晶速率和结晶形态,说明ＰＥＴ／蒙脱土有着很快的结晶速率,不能生成球晶结构,一般只能生成结构不完整的微晶体．ＰＥＴ／蒙脱土在工程塑料和工业纤维领域有潜在的应用前景     

用无外给电子体Ziegler-Natta催化剂催化丙烯聚合的研究

采用 9,9 双 (甲氧基甲基 )芴 (BMMF)为内给电子体合成MgCl2 /TiCl4 /BMMF催化剂 ,以三乙基铝为助催化剂在无需外给电子体的情况下得到高等规度的聚丙烯 .该催化剂具有高活性和高立体定向性 ,并与以邻苯二甲酸二丁酯 (Phthalate)为内给电子体 ,二苯基二甲氧基硅 (DDS)为外给电子体合成的MgCl2 /TiCl4 /Phthalate AlEt3 /DDS催化剂的性能进行比较 ,结果表明无外给电子体催化剂具有较高的活性 ,且聚丙烯的等规度大于 95 % .研究了聚合温度 ,铝钛比等聚合条件对催化剂的活性 ,聚合物的分子量、等规度和熔点的影响 ,并用13 C NMR对聚合物的序列结构进行了分析     

Effect of EtOH/MgCl(2) molar ratios on the catalytic properties of MgCl(2)-SiO(2)/TiCl(4) Ziegler-Natta catalyst for ethylene polymerization

MgCl(2)-SiO(2)/TiCl(4) Ziegler-Natta catalysts for ethylene polymerization were prepared by impregnation of MgCl(2) on SiO(2) in heptane and further treatment with TiCl(4). MgCl(2)·nEtOH adduct solutions were prepared with various EtOH/MgCl(2) molar ratios for preparation of the MgCl(2)-supported and MgCl(2)-SiO(2)-supported catalysts in order to investigate the effect on polymerization performance of both catalyst systems. The catalytic activities for ethylene polymerization decreased markedly with increased molar ratios of [EtOH]/[MgCl(2)] for the MgCl(2)-supported catalysts, while for the bi-supported catalysts, the activities only decreased slightly. The MgCl(2)-SiO(2)-supported catalyst had relatively constant activity, independent of the [EtOH]/[MgCl(2)] ratio. The lower [EtOH]/[MgCl(2)] in MgCl(2)-supported catalyst exhibited better catalytic activity. However, for the MgCl(2)-SiO(2)-supported catalyst, MgCl(2) can agglomerate on the SiO(2) surface at low [EtOH]/[MgCl(2)] thus not being not suitable for TiCl(4) loading. It was found that the optimized [EtOH]/[MgCl(2)] value for preparation of bi-supported catalysts having high activity and good spherical morphology with little agglomerated MgCl(2) was 7. Morphological studies indicated that MgCl(2)-SiO(2)-supported catalysts have good morphology with spherical shapes that retain the morphology of SiO(2). The BET measurement revealed that pore size is the key parameter dictating polymerization activity. The TGA profiles of the bi-supported catalyst also confirmed that it was more stable than the mono-supported catalyst, especially in the ethanol removal region.     

Synthesis and characterization of polyethylene/clay–silica nanocomposites: A montmorillonite/silica‐hybrid‐supported catalyst and in situ polymerization

A novel approach to the preparation of polyethylene (PE) nanocomposites, with montmorillonite/silica hybrid (MT‐Si) supported catalyst, was developed. MT‐Si was prepared by depositing silica nanoparticles between galleries of the MT. A common zirconocene catalyst [bis(cyclopentadienyl)zirconium dichloride/methylaluminoxane] was fixed on the MT‐Si surface by a simple method. After ethylene polymerization, two classes of nanofillers (clay layers and silica nanoparticles) were dispersed concurrently in the PE matrix and PE/clay–silica nanocomposites were obtained. Exfoliation of the clay layers and dispersion of the silica nanoparticles were examined with transmission electron microscopy. Physical properties of the nanocomposites were characterized by tensile tests, dynamic mechanical analysis, and DSC. The nanocomposites with a low nanofiller loading (<10 wt %) exhibited good mechanical properties. The nanocomposite powder produced with the supported catalyst had a granular morphology and a high bulk density, typical of a heterogeneous catalyst system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 941–949, 2004