硒催化CO/H2O选择性还原间二硝基苯制间硝基苯胺

 采用硒作催化剂,乙酸钠为助催化剂,用CO/H2O对间二硝基苯进行部分还原制备了间硝基苯胺. 考察了时间、CO压力、温度、催化剂用量、溶剂和水量等因素对反应的影响. 以四氢呋喃作溶剂,使用摩尔量为间二硝基苯20倍的水和4%的硒,在160 ℃和CO压力1 MPa下反应3 h,间二硝基苯转化率可达100%,间硝基苯胺的选择性和收率均为95.7%.     

利用乙醇重整制氢进行硝基苯原位液相加氢合成苯胺

 利用乙醇液相催化重整制得的氢直接进行硝基苯原位液相加氢合成苯胺. 考察了不同催化剂、反应温度及反应时间等因素的影响. 在以Pt/Al2O3为催化剂,反应温度220 ℃和反应时间3 h的条件下,硝基苯的转化率可达99.3%, 苯胺的选择性为99.8%, 催化剂表现出较高的加氢活性和选择性.     

高活性Ni/HY催化剂加氢催化合成苯胺类化合物的研究

采用浸渍沉淀法制备Ni/HY催化剂,用BET、XRD、TEM、TPR等方法对其进行表征,并将其应用于硝基化合物液相加氢合成苯胺类化合物反应中.结果表明,Ni/HY催化剂具有较高的催化活性,在温和的反应条件下,反应0.5 h后,硝基化合物的转化率和苯胺类化合物的选择性均高达99.0%以上.该催化剂能储存于150℃以下的空气气氛中,活性组分分散度高,且具有良好的磁分离性能.     

聚合物稳定的Ru-Pt/γ-Al2O3双金属催化剂催化2,5-二氯硝基苯选择性加氢

 制备了以聚乙烯吡咯烷酮(PVP)稳定的 Ru-Pt/γ-Al2O3负载型双金属催化剂,用于2,5-二氯硝基苯中的硝基选择性加氢. 考察了催化剂还原方法,反应温度、压力、时间和添加金属离子对反应的影响. 结果表明,用乙醇还原的Ru-Pt/γ-Al2O3催化剂性能明显好于用其它方法还原的催化剂,在50 ℃和氢气压力1.0 MPa的条件下反应1 h,转化率为41.4%,生成2,5-二氯苯胺的选择性为63.5%. 如果在上述反应条件下向该催化体系中加入Sn4+离子,反应的活性和选择性则大幅度提高,转化率达100%,选择性为77.6%,延长反应时间至4 h,选择性可达99.3%,并且没有脱氯产物的生成.     

Ru3(CO)9(TPPTS)3催化的水/有机两相芳香硝基化合物CO选择性还原的研究

将水溶性膦/钌配合物Ru₃(CO)₉(TPPTS)₃(TPPTS:三苯基膦三-间磺酸钠)用于以CO为还原剂的水/有机两相芳香硝基化合物选择还原为芳胺的反应,发现相转移催化剂对反应有明显的促进作用,其中以添加十六烷基三甲基溴化铵(CTAB)的效果最好.以邻氯硝基苯为底物考察了相转移催化剂浓度、NaOH浓度、反应温度、压力等对反应转化率和选择性的影响.当反应条件为120℃,4MPa,3mol/LNaOH时,反应8h,邻氯硝基苯的转化率和邻氯苯胺的选择性均可达到99.9%.而且对含有羰基、氰基的芳香硝基化合物也有很高的活性和选择性.催化剂循环3次后,邻氯硝基苯的转化率和邻氯苯胺的收率仍可达到92%.     

水溶性配合物[RuCl2(TPPTS)2]2催化卤代硝基苯选择性加氢

以合成的水溶性钌配合物[RuC l2(TPPTS)2]2作为催化剂,用于水/有机两相体系中催化卤代硝基苯中硝基的选择性加氢反应.以对-氯硝基苯为底物,考察了反应温度、氢气压力、催化剂浓度、水溶液的pH值等对对-氯硝基苯转化率和生成对-氯苯胺选择性的影响.在100℃,氢气压力3.0 MPa时,反应6h,对-氯硝基苯转化率可达100%,生成对-氯苯胺的选择性可达95.2%.该催化剂对其他卤代硝基苯的加氢反应也表现出较高的催化活性.     

水溶性含钌-铂双金属催化剂催化卤代芳香硝基化合物选择性加氢

考察了水溶性Ru/Pt-TPPTS双金属催化剂催化卤代芳香硝基化合物的加氢性能.实验结果表明,在Ru-TPPTS中添加铂或钯后,反应活性明显提高,尤其是Ru/Pt-TPPTS双金属催化剂更表现出显著的双金属协同效应.在pH₂=1.0MPa,70℃,反应2h的条件下,双金属催化剂0.50Ru/0.50Pt-TPPTS催化对-氯硝基苯加氢生成对-氯苯胺的反应转化率达到100%.对于取代基和取代位置不同的一些卤代硝基苯加氢,该双金属催化剂也表现出很高的催化活性和生成卤代苯胺的选择性,脱卤反应的程度很小.     

温控相分离纳米Rh催化1,5-环辛二烯选择性加氢反应

发现离子液体[CH3(OCH2CH2)nN+Et3][CH3SO3-](ILPEG,n=12,16,22)具有临界溶解温度特性,据此确证了以ILPEG为稳定剂制得的Rh纳米催化剂具有温控相分离催化功能,并将其用于1,5-环辛二烯(1,5-COD)选择性加氢制环辛烯(COE)的反应中.在优化的反应条件下,1,5-COD转化率和COE选择性分别为99%和90%;Rh纳米催化剂经简单分相即可与产物分离,催化剂循环使用10次,其活性和选择性无明显降低.     

碳纳米管负载Pd/SnO2催化剂的制备及其催化邻氯硝基苯加氢性能

采用化学还原法制备了不同Sn/Pd摩尔比的碳纳米管(CNTs)负载Pd/SnO2催化剂,并将该催化剂用于邻氯硝基苯(o-CNB)的选择加氢反应.采用透射电镜、X射线衍射和电感耦合等离子体技术对所制备的Pd/SnO2/CNTs催化剂进行了表征.结果表明,Sn/Pd摩尔比对该催化剂的邻氯硝基苯选择加氢反应性能影响显著.当Sn/Pd摩尔比为11时,催化剂的活性最高,在常压,60℃反应60 min,o-CNB转化率为96%.该催化剂还具有高的邻氯苯胺(o-CAN)选择性,o-CNB转化率达到100%时,脱氯副产物苯胺选择性小于5%.在相同条件下,浸渍法制备的2.4%Pd/CNTs催化剂上脱氯副反应严重,当o-CNB完全转化时,o-CAN选择性只有22%,副产物苯胺选择性则高达78%.     

氯代苯胺液相催化加氢合成环己酮

提出了一种催化降解氯代苯胺高选择性合成环己酮的技术.在La修饰Pd/Al2O3催化剂作用下,通过催化加氢的方法实现了由多氯代苯胺(2,4,6-三氯苯胺和2,4,-二氯苯胺)高选择性地合成环己酮(不含环己醇).在优化的反应条件下,2,4,6-三氯苯胺加氢生成环己酮的转化率和选择性分别为100%和98.6%(没有检测到环己醇);2,4,-二氯苯胺加氢生成环己酮的转化率和选择性均为100%.氯代苯胺在Pd/La-Al2O3催化剂表面首先发生加氢脱氯/N-甲基化等反应生成苯胺、N-甲基苯胺和N,N-二甲基苯胺等中间产物,随后这些中间产物发生苯环加氢、氨基水解/醇解等反应得到环己酮;氯代苯胺上Cl元素的存在和体系中水的含量是影响环己酮选择性的重要因素.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.