低硅铝比ZSM-5分子筛上C4烃的催化裂解反应

以低硅铝比(n(SiO2)/n(Al2O3)=20-45)的ZSM-5分子筛为催化剂, 研究了混合C4烃的催化裂解反应, 并对不同硅铝比的ZSM-5分子筛进行了酸性表征. 混合C4烃的催化裂解反应结果表明, 低硅铝比的ZSM-5分子筛具有较高的低温催化活性, 高硅铝比ZSM-5分子筛催化剂上乙烯和丙烯的收率高于低硅铝比ZSM-5分子筛催化剂, 低硅铝比ZSM-5分子筛上苯和甲苯的收率高于高硅铝比ZSM-5分子筛催化剂. 在反应温度为625 ℃时, 硅铝比为20的ZSM-5分子筛催化剂上乙烯、丙烯、苯和甲苯的总收率可达79.42%. 酸性表征结果表明, 硅铝比低的ZSM-5分子筛具有更多的Bronsted(B)酸酸量、Lewis(L)酸酸量及总酸酸量, 这是低硅铝比ZSM-5分子筛具有低温高活性及高的苯和甲苯收率的原因.     

低硅铝比ZSM-5分子筛上C4烃的催化裂解反应

以低硅铝比(n(SiO2)/n(Al2O2)=20-45)的ZSM-5分子筛为催化剂,研究了混合C4烃的催化裂解反应,并对不同硅铝比的ZSM-5分子筛进行了酸性表征.混合C4烃的催化裂解反应结果表明,低硅铝比的ZSM-5分子筛具有较高的低温催化活性,高硅铝比ZSM-5分子筛催化剂上乙烯和丙烯的收率高于低硅铝比ZSM-5分子筛催化剂,低硅铝比ZSM-5分子筛上苯和甲苯的收率高于高硅铝比ZSM-5分子筛催化剂.在反应温度为625℃时,硅铝比为20的ZSM-5分子筛催化剂上乙烯、丙烯、苯和甲苯的总收率可达79.42%.酸性表征结果表明,硅铝比低的ZSM-5分子筛具有更多的Bronsted(B)酸酸量、Lewis(L)酸酸量及总酸酸量,这是低硅铝比ZSM-5分子筛具有低温高活性及高的苯和甲苯收率的原因.     

高硅MCM-22分子筛的合成及其C4烯烃裂解性能

由于丙烯衍生物需求量迅速增长,致使全球丙烯需求增长速率超过乙烯,近年来,人们一直在寻求新的丙烯增产的方法,采用分子筛作为催化剂,通过裂解C4及C4以上富烯烃原料来获取高收率的丙烯已引起国内外学者的高度关注,Rubinm等于1990年首先合成出MCM-22分子筛,由于其特有的酸性和独特的孔结构而被广泛用于各类化学反应中,迄今尚未见文献报道MCM-22分子筛在C4烯烃裂解反应中的催化性能研究,由于高硅铝比分子筛具有相对较高的热稳定性和水热稳定性,     

SAPO-34分子筛催化丁烯转化制丙烯的研究

通过水热法合成SAPO-34分子筛,将其制成催化剂用于催化丁烯转化制取丙烯,考察了反应温度、空速和铝磷比等对催化性能的影响;还比较了SAPO-34分子筛与ZSM-5分子筛催化该反应的差异.结果表明,在实验范围内,反应温度升高会使得丁烯的转化率明显增高,且丙烯选择性提高;而空速增加,则丁烯的转化率和丙烯选择性降低;铝磷比越大,对丙烯的选择性越差.在有效的反应时间内,SAPO-34分子筛催化效果好于ZSM-5分子筛,但单程寿命较ZSM-5分子筛短.     

高硅分子筛ZSM-23催化裂解C4烷烃制乙烯丙烯的研究

采用廉价的硅溶胶作为硅源,吡咯烷为模板剂,静态水热晶化法合成出不同硅铝比的ZSM-23分子筛.采用XRD,SEM,吡啶吸附红外光谱等技术,对合成的ZSM-23分子筛的结构、形貌、表面酸性质进行了表征.并进行了所制样品对C4烷烃催化裂解制乙烯丙烯反应催化性能的研究.本文详细考察了硅铝比、反应温度、反应空速以及催化剂稳定性等各种因素对催化性能的影响.结果表明,ZSM-23分子筛的乙烯丙烯收率达到56.0%,丁烷转化率达到88.9%.     

高浓度体系制备ZSM-5分子筛及碱处理后甲醇制丙烯性能

在高浓度体系下,以粗孔硅胶和偏铝酸钠为原料,TPABr为模板剂,水热晶化法制备了ZSM-5分子筛,单釜产率23％.用不同浓度的氢氧化钠溶液对ZSM-5分子筛进行改性,采用XRD、FT-IR、SEM、NH3-TPD、XRF、N2物理吸附等方法对改性前后的样品进行了表征,并考察了改性后ZSM-5分子筛甲醇催化转化制丙烯(MTP)反应性能.结果表明,氢氧化钠改性未破坏分子筛的骨架结构,改性后样品的酸量、介孔孔容和BET比表面积均有增加,从而改善了催化剂的抗积碳性能和反应性能.在MTP反应中,增产丙烯的效果不明显,但表现出了更好的催化稳定性(催化剂使用寿命从85 h提升至110 h),并且有利于提高副产物汽油组分(∑C5+)的产量.     

氟硅酸铵改性的HZSM-5催化剂的表征及其碳四烯烃裂解催化性能

 采用X射线衍射、扫描电镜、 N2低温吸附、核磁共振、氨程序升温脱附和吡啶吸附红外光谱等表征手段考察了氟硅酸铵改性对成型后的HZSM-5分子筛催化剂物化性能的影响,并在连续固定床反应器中考察了改性前后催化剂在碳四烯烃裂解制丙烯反应中的催化性能. 结果表明,氟硅酸铵改性不但不会破坏HZSM-5分子筛的骨架结构,而且能起到疏通催化剂孔道的作用,使催化剂平均孔径增大. 改性后催化剂的L酸酸强度降低,而B酸酸强度有所提高. 碳四烯烃裂解反应结果表明,氟硅酸铵改性可使催化剂的催化性能得到改善,其活性稳定性,水热稳定性及丙烯收率都得到了一定程度的提高.     

W-ZSM-5催化剂C4烯烃裂解制丙烯催化性能研究

采用浸渍法制备了W-ZSM-5催化剂,用X-射线衍射(XRD)、N2吸附、NH3-TPD和H2-TPR等表征手段,研究了W的添加对HZSM-5催化剂物化性质的影响,并考察了W-ZSM-5催化剂在C4烯烃催化裂解制丙烯反应中的催化性能.结果表明,W的添加中和了催化剂的部分强酸位,降低了催化剂的酸性和酸强度,抑制了芳构化和氢转移等副反应的发生,增强了催化剂的抗积炭性能,促进了催化裂解过程中歧化反应的发生,有利于提高丙烯的选择性和收率.当W含量为3.2%时,催化剂的丙烯选择性和收率值达到最大,分别为47.4%和41.3%.     

水蒸气处理对ZSM-5酸性及其催化丁烯裂解性能的影响

 考察了水蒸气处理温度和时间对ZSM-5分子筛酸性及其催化丁烯裂解性能的影响. 结果表明,通过水蒸气处理可降低ZSM-5分子筛的酸量和酸强度,明显提高产物中丙烯与乙烯的选择性和收率,抑制副产物芳烃和低碳烷烃的生成. 用柠檬酸脱除水蒸气处理过程中产生的非骨架铝,可提高ZSM-5分子筛孔道的容碳能力,从而提高催化剂的稳定性. 考察了反应条件对催化剂性能的影响,结果表明较佳的反应条件为WHSV=3.5～8.8 h-1,p=0.06～0.1 MPa,θ=600～620 ℃.     

ZSM-5分子筛的粒径可控合成及其在甲醇转化中的催化作用

以四丙基氢氧化胺为模板剂、聚乙二醇为添加剂,水热合成了粒径在0.1～14 μm且分布均一的ZSM-5分子筛,并采用XRD、SEM、BET、Py-IR、NH₃-TPD和ICP等技术对其进行了表征,考察了不同粒径分子筛在甲醇转化制碳氢化合物反应中的催化作用。结果表明,通过调变PEG添加量、硅源种类和水含量以及控制陈化和晶化条件,可以在较大范围内调变分子筛晶粒尺寸。随着粒径的减小,ZSM-5晶粒的聚集程度、比表面积和Si/Al比提高,而结晶度、BrØnsted酸浓度和总酸量有所下降。在甲醇催化转化制碳氢化合物的反应中,粒径为0.1 μm的分子筛催化稳定性最好;随着粒径的增大,其稳定性逐渐下降,粒径为14 μm的分子筛催化剂寿命明显降低。同时,粒径对甲醇转化产物分布也有较大影响;小粒径分子筛有利于生成轻质烃类(C₁～C₄),而大粒径分子筛对C₅以上烷烃和芳烃的选择性较高。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。