分散聚合-种子溶胀聚合法制备中空微球的研究

采用分散聚合法制备聚苯乙烯(PSt).以甲苯一正辛醇作致孔溶剂,过氧化苯甲酰为引发剂,PSt为单分散种球,反应单体苯乙烯和交联单体二乙烯基苯(DVB)通过种子溶胀聚合法,在水介质中制备了呈单分散的中空聚合物微球[P(St-DVB),粒径5 μm-8μm],其形态及热力学行为经SEM,DSC和TGA表征.讨论了DVB用量及溶剂组成对P(St-DVB)形态的影响.     

种子乳液聚合法制备中空多孔聚合物微球

用分散聚合法制得粒径约为3μm的聚苯乙烯种子微球,通过溶胀,种子乳液聚合及萃取得到中空多孔聚合微球,使用扫描电镜检测了其中空多孔形貌和粒径,并讨论了成孔机理。     

单分散、大粒径聚苯乙烯微球的制备

以聚乙烯基吡咯烷酮为分散剂、偶氮二异丁腈为引发剂、醇／水混合物为分散介质进行了苯乙烯的分散聚合，讨论了初始单体浓度、分散剂用量、引发剂浓度、分散介质组成和反应温度等反应条件对所得聚合物颗粒直径和直径分布的影响．通过大量的试验，筛选出了较为理想的分散聚合的条件及配方，制备出了粒径为４８μｍ的单分散聚苯乙烯微球．然后，以分散聚合所制得的聚合物颗粒为种子，用动力学溶胀法制成了粒径增大近四倍的单分散、大粒径聚苯乙烯微球，并讨论了滴水速度和补加分散剂对溶胀的影响     

种子溶胀法制备单分散高交联聚苯乙烯微球

以分散聚合法制得平均粒径为1.80μm的聚苯乙烯微球为种子,与溶胀剂和单体、交联剂的混合物经二步溶胀聚合法,制备了单分散高交联聚苯乙烯微球。讨论了单体浓度和醇水比对种球的影响,以及溶胀剂的种类、溶胀剂浓度、交联剂浓度、溶胀温度和搅拌速度等因素对交联聚苯乙烯微球粒径及分散系数的影响。用扫描电子显微镜、离心式粒度分析仪及DSC分析测试技术对微球的外观形貌、粒径大小及分布和玻璃化转变温度分别进行了表征。结果表明,当溶胀剂质量分数为25%、交联剂质量分数为23%、溶胀温度30℃、搅拌速度为150r/min时,可制得平均粒径为6.20μm且单分散性较好的高交联聚苯乙烯微球。     

PSt种子与“花瓣”形PSt/PAN复合颗粒的制备

以过硫酸钾为引发剂,在乙醇/水的混合介质中使苯乙烯进行无皂乳液聚合,得到了单分散亚微米级聚苯乙烯(PSt)微球.用扫描电子显微镜研究了引发剂浓度、单体浓度、反应温度和溶剂组成对PSt微球粒径的影响.结果表明,改变上述条件能明显影响其粒径.以所得单分散聚苯乙烯微球为种子,在丙烯酸单封端聚乙二醇大分子单体存在的条件下,使丙烯腈和少量苯乙烯进行新的无皂种子乳液聚合,在合适的条件下制得到了“花瓣”形的聚合物复合颗粒,为深入探讨这类特殊形态聚合物颗粒的形成机理提供了新的佐证.     

单分散多孔交联聚苯乙烯色谱填料的合成(英文)

用分散聚合法合成了粒径为２μｍ的单分散ＰＳ种球,直接将种球用含ＳＴ和ＤＶＢ的乳液进行膨胀－聚合,得到粒径为８．８μｍ的单分散共聚微球。经甲苯抽提后,得到单分散多孔ＳＴ／ＤＶＢ色谱填料。报道的方法不需要对种球进行预膨胀（活化）,缩短了反应周期,大幅度提高了色谱填料微球的单分散性。     

苯乙烯和N-乙烯基吡咯烷酮共聚物/Ag复合微球的制备及性能研究

首先用无皂乳液聚合法制备了单分散聚苯乙烯(PSt)乳液,以此为种子乳液,使用N,N-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,进行苯乙烯和N-乙烯基吡咯烷酮(NVP)共聚合制备了以PSt为核、St和NVP共聚物为壳的具有核-壳结构的聚合物微球(P(St-NVP)).以此微球为模板通过化学沉积法得到了粒径分布均匀、单分散的P(St-NVP)/Ag复合微球.傅里叶红外光谱、X-射线衍射、扫描电镜、透射电镜、激光粒度仪和紫外-可见光谱对复合微球的结构、形貌、物相及催化性能进行了表征.结果表明,P(St-NVP)/Ag复合微球具有规则的球形结构,粒径在400～700 nm之间,随交联剂浓度或种子乳液浓度的增加,复合微球粒径减小.粒径在十几个纳米左右的银粒子均匀分布在微球表面和内部.载银复合微球在NaBH4还原4-硝基苯酚为4-氨基苯酚的模型反应中表现出较高的催化活性.     

两步种子溶胀聚合研究进展*

由两步种子溶胀聚合法制备的聚合物微球尺寸均一可控,制备的多孔微球孔径、孔分布可控,被广泛应用于色谱柱填料、离子交换树脂、生物分离和催化剂载体等领域。本文介绍了两步种子溶胀聚合的聚合工艺;阐述了两步种子溶胀聚合的溶胀机理以及用该法制备多孔微球的致孔机理;进一步分析了影响两步种子溶胀聚合的各种因素：包括聚合过程的控制以及聚合配方的控制因素等;简要综述了通过该方法所制备的多孔聚合物微球,并对两步种子溶胀聚合方法今后的发展进行了展望。     

单分散交联聚苯乙烯微球HPLC固定相的合成

用分散聚合物合成了单分散聚苯乙烯微球种子，然后用种子聚合法合成了交联的聚苯乙烯向球，其粒径范围可控制在２μｍ～４μｍ，考察了反应条件对微球粒径和粒径分布的影响，确定了最佳合成条件，初步考察了交联微球的ＨＰＬＣ性能。     

带羧基单分散彩色微球的制备

采用两步活性溶胀种子聚合法, 制备了可用于免疫检测的3种不同颜色的表面带有羧基功能基的粒径在400—800 nm之间的彩色单分散微球. 先用无皂乳液聚合法制备出单分散聚苯乙烯种子, 然后用邻苯二甲酸二正丁酯(DBP)作为溶胀剂对微球进行溶胀, 溶涨后的种子模板再用混溶的苯乙烯、二乙烯苯、丙烯酸、双键彩色染料以及引发剂(BPO)溶胀, 升温聚合后得到理想的单分散微球. 考察了DBP和单体用量、各单体配比及染料对微球的形貌和单分散性的影响.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.