负载型Co-Cr氧化物催化剂上CO2氧化乙烷脱氢制乙烯反应的研究

制备了一系列不同Co／Cr比例的Co-Cr／SiO2和Co-Cr／γ-Al2O3催化剂，并应用XRD等技术对所制样品进行了表征．在常压连续流动固定床石英反应器中考察了它们对CO2乙烷氧化脱氢反应的催化性能．实验结果表明，Co-Cr／SiO2和Co-Cr／γ-Al2O对CO2乙烷脱氢制乙烯都有较高的催化活性，其活性都明显高于负载单一组分的催化剂．以γ-Al2O为载体的催化剂活性明显比以SiO2为载体的催化剂活性高．1％Co-5％Cr／γ-Al2O活性最高，973K乙烷的转化率达25．57％，乙烯的选择性和收率分别达94．28％、24．10％．     

纳米Cr2O3系列催化剂上CO2氧化乙烷脱氢制乙烯反应

 采用溶胶－凝胶法和共沸蒸馏法耦合技术制备了纳米Cr2O3催化剂，并采用共沉淀法和共沸蒸馏法耦合技术制备了纳米Cr2O3／Al2O3，Cr2O3／ZrO2和Cr2O3／MgO复合催化剂．应用BET，XRD，XPS，TPR和TEM等物理化学方法对催化剂的结构和物化性质进行了表征，并考察了该系列催化剂上CO2氧化乙烷脱氢制乙烯的反应性能．结果表明，纳米Cr2O3催化剂上乙烷和CO2的转化率均明显高于常规Cr2O3催化剂，但乙烯的选择性低于常规Cr2O3催化剂；纳米复合催化剂中的复合成分显著影响催化剂的催化性能．其中，10％Cr2O3／MgO纳米复合催化剂在温度为973K时，乙烷转化率和乙烯选择性分别可达到61．54％和94．79％．纳米催化剂表面Cr的还原性以及Cr6＋／Cr3＋比值是影响乙烷转化率和乙烯选择性的重要因素．     

乙烷与CO2制乙烯反应的热力学和动力学研究

乙烷与ＣＯ２的主要反应及其热力学研究表明，乙烷与ＣＯ２反应很复杂，提高ＣＯ２氧化乙烷脱氢生成乙烯的选择，关键在一催化剂的开发；ＣＯ２不但可提高乙灶脱氢制乙烯的热力学平衡转化率，而且可与催化剂表面的积碳发生反应，延长催化剂的使用寿命。研究了催化剂上乙烷与ＣＯ２制乙烯反应的动力学，确定了ＣＯ２氧化乙烷脱氢反应的动力学方程及参数，表明乙烷与ＣＯ２制乙烯的反应速度比乙烷热裂解制乙烯的反应速度要大得多。     

羟基化氮化硼催化乙烷氧化脱氢制乙烯（英文）

乙烯是最为重要的化工原料之一,目前其工业来源主要来自于烃类的水蒸汽裂解过程.该过程本质上是一个高温均相裂解过程,温度(800℃)高,能耗大,碳排放严重.乙烷氧化脱氢制乙烯属于放热反应,反应温度低,速率快,无积碳等限制,是一条更富有竞争力的工艺路线.然而,常用的金属或金属氧化物催化剂容易导致乙烯深度氧化,从而降低了乙烯选择性.纳米碳材料在烃类氧化脱氢反应中展现出一定的催化活性,但容易被氧化,难以用于反应温度高的乙烷氧化脱氢反应.本文报道了羟基化的氮化硼(BNOH)可高效催化乙烷氧化脱氢制乙烯.氮化硼边沿羟基官能团脱氢生成了动态活性位,从而引发了乙烷的脱氢反应.BNOH对乙烷氧化脱氢制乙烯显示出高选择性.当乙烷转化率在11%,乙烯选择性可高达95%;当乙烷转化率增加到40%,乙烯选择性保持在90%.重要的是,当乙烷转化率超过60%时,BNOH仍然可保持80%的乙烯选择性以及50%的乙烯收率.这些性能指标与现有工业乙烷水蒸气裂解过程运行性能相当.进一步优化反应条件,BNOH催化剂能够实现高达9.1g_(C2H4)g_(cat)~(-1)h~(-1)的时空收率.经过200 h的氧化脱氢反应测试,BNOH催化剂活性和选择性基本恒定,表明其具有非常好的稳定性.X射线粉末衍射结果显示,反应前后BNOH催化剂的物相没有发生变化.透射电子显微镜测试证实,反应后BNOH催化剂的形貌和微观结构也没有明显改变.X射线光电子能谱结果显示,反应200 h后BNOH催化剂表面的氧含量仅从反应前的6.9 atom%微增到8.3 atom%.~1H固体核磁共振谱测试显示,反应200 h后,BNOH催化剂上羟基含量无明显改变.结合原位透射红外光谱和同位素示踪实验,初步确定了BNOH催化剂上引发乙烷氧化脱氢反应的活性中心.氮化硼边沿的氧官能团并不能引发乙烷的氧化脱氢反应,而羟基官能团才是氧化脱氢反应发生的活性位.在乙烷氧化脱氢条件下,分子氧脱除羟基官能团上的氢原子动态生成BNO~·和HO_2~·活性位.密度泛函理论计算表明,乙烷首先在BNO~·或HO_2~·位活化生成乙基自由基,这些中间物进一步与气相氧物种发生反应脱氢生成乙烯.动力学测试结果也验证了上述实验和理论结果.     

羟基化氮化硼催化乙烷氧化脱氢制乙烯

乙烯是最为重要的化工原料之一,目前其工业来源主要来自于烃类的水蒸汽裂解过程.该过程本质上是一个高温均相裂解过程,温度(>800?℃)高,能耗大,碳排放严重.乙烷氧化脱氢制乙烯属于放热反应,反应温度低,速率快,无积碳等限制,是一条更富有竞争力的工艺路线.然而,常用的金属或金属氧化物催化剂容易导致乙烯深度氧化,从而降低了乙烯选择性.纳米碳材料在烃类氧化脱氢反应中展现出一定的催化活性,但容易被氧化,难以用于反应温度高的乙烷氧化脱氢反应.本文报道了羟基化的氮化硼(BNOH)可高效催化乙烷氧化脱氢制乙烯.氮化硼边沿羟基官能团脱氢生成了动态活性位,从而引发了乙烷的脱氢反应.BNOH对乙烷氧化脱氢制乙烯显示出高选择性.当乙烷转化率在11%,乙烯选择性可高达95%;当乙烷转化率增加到40%,乙烯选择性保持在90%.重要的是,当乙烷转化率超过60%时,BNOH仍然可保持80%的乙烯选择性以及50%的乙烯收率.这些性能指标与现有工业乙烷水蒸气裂解过程运行性能相当.进一步优化反应条件,BNOH催化剂能够实现高达9.1 gC2H4 gcat-1 h-1的时空收率.经过200 h的氧化脱氢反应测试,BNOH催化剂活性和选择性基本恒定,表明其具有非常好的稳定性.X射线粉末衍射结果显示,反应前后BNOH催化剂的物相没有发生变化.透射电子显微镜测试证实,反应后BNOH催化剂的形貌和微观结构也没有明显改变.X射线光电子能谱结果显示,反应200 h后BNOH催化剂表面的氧含量仅从反应前的6.9 atom%微增到8.3 atom%.1H固体核磁共振谱测试显示,反应200 h后,BNOH催化剂上羟基含量无明显改变.结合原位透射红外光谱和同位素示踪实验,初步确定了BNOH催化剂上引发乙烷氧化脱氢反应的活性中心.氮化硼边沿的氧官能团并不能引发乙烷的氧化脱氢反应,而羟基官能团才是氧化脱氢反应发生的活性位.在乙烷氧化脱氢条件下,分子氧脱除羟基官能团上的氢原子动态生成BNO·?和HO2·?活性位.密度泛函理论计算表明,乙烷首先在BNO·?或HO2·?位活化生成乙基自由基,这些中间物进一步与气相氧物种发生反应脱氢生成乙烯.动力学测试结果也验证了上述实验和理论结果.     

CATALYTIC BEHAVIOR OF DOPED MTiO_3 CATALYSTS FOR OXIDATIVE DEHYDROGENATION OF ETHANE

用Ｌｉ＋部分替代ＭＴｉＯ３（Ｍ＝Ｃａ、Ｓｒ）催化剂中的Ｔｉ４＋，明显地提高了乙烷氧化脱氢（ＯＤＨＥ）反应中乙烯的选择性。在ＣａＴｉ０．９Ｌｉ０．１Ｏ３－δ催化剂上，反应温度为８５０℃时，乙烯选择性为７７．４％，乙烷转化率为８１．７％。Ｌｉ掺杂的作用是增加了催化剂的Ｐ型半导性和未充分还原的氧物种数目。     

空石英管中乙烷氧化脱氢制乙烯

使用空石英反应管,对乙烷氧化脱氢制乙然反应进行了研究。在６３３℃,可得到乙烷转化率７９％,乙烯选择性６６％,乙烯单程收率为５２％,此结果比已知文献报道的使用催化剂的结果毫不逊色。采用空石英反应管的反应特点是在较低的乙烷转化率时,可以得到很高的乙烯选择性,其主要反应副产物为ＣＯ。     

Co-MCM-41催化剂上临CO2-乙烷脱氢反应的研究

合成了不同Co掺杂量的Co-MCM-41分子筛.用XRD,FTIR和TG-DTA等技术对所制样品进行表征.在常压连续流动固定床反应器上考察了它们对临CO₂-乙烷脱氢制乙烯反应的性能,结果表明,3%Co-MCM-41在973K可使乙烷的转化率达到39.54%,乙烯的选择性达到98.59%,收率达到38.98%.Co的掺杂量和反应温度等条件对该反应均有一定影响.Co-MCM-41对乙烷催化脱氢制乙烯同样也有很高的活性.引入CO₂可消除积炭对催化剂活性的影响,更有利于催化反应的进行.     

纳米Cr2O3的制备、表征及催化性能

首次采用溶胶-凝胶法与共沸蒸馏法耦合技术制备了纳米Cr2O3粉体，并运用BET、TEM、XRD、FT-IR、XPS及H2-TPR对其进行表征，同时采用CO2氧化乙烷脱氢制乙烯反应作为探针反应，考察了纳米Cr2O3的催化性能。首次发现纳米ErgO3的FT-IR谱出现了蓝移现象，并且630cm^-1附近的伸缩振动峰强度增强。初步探讨了纳米氧化物的IR蓝移和红移的原因，指出晶型是影响纳米氧化物红外光谱特征的重要因素。实验结果表明纳米Cr2O3上乙烷和CO2转化率均明显高于常规Cr2O3催化剂；在700℃下，乙烷转化率高达77．1％，而乙烯产率达到了58．98％。     

激光促进LiClO4·Pb3(PO4)2复合物表面上的乙烷氧化脱氢反应

 制备了LiClO4,Pb3（PO4）2和LiClO4·Pb3（PO4）2复合物催化剂,用XRD和IR表征了催化剂的晶相及表面结构,并用化学吸附IR和TPD研究了催化剂样品对乙烷的化学吸附性能,用LSSR考察了乙烷氧化脱氢生成乙烯的反应规律．结果表明,催化剂表面的ClO和PO键是乙烷的主要吸附位．LiClO4与Pb3（PO4）2的相互作用促进了ClO键对乙烷的吸附活化能力．在一定反应条件下,乙烷转化率与体系的能量利用率有关,复合物催化剂比单纯的LiClO4和Pb3（PO4）2可更有效地利用激光光能．温度对LSSR反应有一定的辅助作用．     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.