MgCl2/Et3N催化合成α,β-不饱和氰代酯

用MgCl₂/Et₃N催化氰乙酸乙酯和芳香醛的缩合反应合成α,β-不饱和氰代酯, 反应可在室温进行. 产率87%～92%.     

NaHSO4•SiO2催化合成β-烯胺酮(酯)

NaHSO₄•SiO₂作催化剂, 1,3-二羰基化合物和伯胺在室温下反应合成了一系列β-烯胺酮(酯), 该法反应条件温和, 产率高, 催化剂能回收再利用.     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

Ce1－xNdxO2－δ固溶体的电子顺磁共振谱和阻抗谱的研究

利用溶胶-凝胶方法在800 ℃焙烧10 h后, 合成了固溶体Ce_1－xNd_xO_2－δ (x＝0.05～0.55), X射线衍射(XRD)测试表明固溶体已经形成立方萤石结构; 电子顺磁共振谱(EPR)研究表明在固溶体Ce_1－xNd_xO_2－δ中随着掺杂量x的增大, Ce^3＋离子含量减少, 说明掺杂Nd^3＋离子可以抑制Ce^4＋的还原; 交流阻抗谱的测量表明固溶体Ce_0.9Nd_0.1O_2－d 具有离子导电特性, 600和700 ℃时的电导率分别为4.25×10^－3和1.12×10^－2 S•cm^－1, 活化能为0.68 eV.     

CNT/β-AgVO3混杂材料的制备及其光催化分解水析氧性能研究

采用水热法合成出单斜结构的β-AgVO₃纳米棒和CNT/β-AgVO₃光催化剂,在可见光模拟系统中以碘酸钾为电子捕获剂,检测氧气生成速率表征催化剂的光催化性能, 并借助X射线衍射(XRD)分析、扫描电镜(SEM)、透射电镜(TEM)、紫外-可见光漫反射吸收光谱(UV-Vis)等对催化剂粉体进行了表征.实验结果表明,CNT附着在β-AgVO₃颗粒表面有利于光生电子的转移和光解水析氧反应.CNT/β-AgVO₃催化剂较之纯β-AgVO₃催化剂活性显著提高.当CNT附着量为1.5%时,析氧速率可稳定在250 μmol·g^-1·h^-1.     

xLi2MnO3-(1-x)LiNi0.7Co0.3O2的低温燃烧合成及电化学性能研究

采用低温燃烧法合成了锂离子电池正极材料xLi₂MnO₃-(1-x)LiNi_0.7Co_0.3O₂,对合成产物的结构、形貌和电化学性能进行了系统的研究, 通过单因素试验对合成条件和材料的组成进行了优化。结果表明:采用低温燃烧法合成的富锂层状正极材料具有α-NaFeO₂型层状结构、球状形貌和良好的电化学性能;其最佳合成条件为:回火温度850℃, 回火时间20 h;Li₂MnO₃的最佳配比为x=0.7.在此条件下合成的0.7Li₂MnO₃-0.3LiNi_0.7Co_0.3O₂,最高放电比容量达到263.1 mAh·g^-1,并具有良好的循环性能和倍率性能。     

纳米Mn-Zn铁氧体的制备和研究

Nanosize manganese zinc ferrites were fabricated by hydrothermal precipitation route using Fe₂(SO₄)₃, ZnSO₄·7H₂O, MnSO₄·H₂O as material, then some calcinated at 500 ℃ and studied by XRD, TEM, IR and VSM. The results showed that the products were spinel crystal structure and uniformly sized nanoparticles (15～25 nm) with little aggregation. The analysis of IR showed that the superficial water can be eliminated, but that was embedded in crystal lattice can not be removed by calcinating. The effect Zn content x on the lattice (a) of nanosize Mn_1-xZn_xFe₂O₄ was also discussed. The lattice of nanosize Mn_1-xZn_xFe₂O₄ decreases with x increasing; and its value deviated the standard lattice (a₀) of normal size manganese zinc ferrites. A lot of water was absorbed during the hydrothermal process owing to the large surface of nanosize particles. The change of magnetic properties of Mn_xZn_1-xFe₂O₄ with x increasing was studied: nanosize Mn_xZn_1-xFe₂O₄ particles synthesized by us exhibited peculiar magnetic properties curve with Zn content (x) increasing, Superparamagnetic behaviors of the synthesized ZnFe₂O₄ samples were confirmed by magnetic characterization, which can be explained by the difference between the distribution of the metal ions (Mn²⁺, Zn²⁺ and Fe³⁺) among the tetrahedral (A) and the octahedral (B) sites of nanosize ferrite and that of bulk ferrite.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

Ba0.4Sr0.6Co1-xFexO3-δ系阴极材料的制备和表征

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ(x=0.0～0.8)系列粉体。利用XRD和SEM对材料的结构和微观形貌进行分析,用直流四端子法测量了烧结陶瓷体在中温(450～800 ℃)范围内的电导率。结果表明,制备的样品为单一钙钛矿相,随着Fe含量增加,XRD衍射峰值向高角度方向稍有偏移。电导率随着温度及Fe含量的变化出现极大值,在x＜0.2时,Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ系列烧结体在中温(450～800 ℃)区的电导率,随Fe掺入量的增大而增大,x=0.2样品的电导率最高,800 ℃时达244.7 S·cm^-1,远超过文献报道值,进一步增大Fe含量导电性能变差。     

中温固体氧化物燃料电池阴极材料Sm2-xCexCuO4的制备与性能研究

采用甘氨酸-硝酸盐法合成了新型中温固体氧化物燃料电池(ITSOFC)阴极材料Sm_2-xCe_xCuO₄(SCC，x=0.0～0.25)。利用XRD和SEM对材料的结构、化学稳定性和微观形貌进行分析表明，该阴极材料与电解质Ce_0.9Gd_0.1O_1.9(CGO)在1 000 ℃烧结时不发生反应;且烧结2 h后，二者之间形成良好的接触界面。利     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

纳米Ce1—xMnxO2催化剂上乙醇催化氧化发光研究

研究了纳米Ce_1—xMn_xO₂上乙醇催化氧化发光特性, 重点考察了反应温度和催化剂组成(Ce/Mn比)对发光强度的影响规律. 为研究催化发光机理, 在相近的反应条件下考察了纳米Ce_1—xMn_xO₂上乙醇催化氧化反应的活性和选择性. 结果表明: 催化发光强度与催化反应中生成CH₃CHO的产率有很好的顺变关系, 表明CH₃CHO是导致C₂H₅OH分子在纳米Ce_1—xMn_xO₂催化剂上氧化发光的“活性分子”.     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

利用薯蓣皂甙元完整骨架形式合成1α,25-二羟基维生素D3

首次利用薯蓣皂甙元的完整骨架经16步反应以7.6%的总收率合成了骨化三醇(1α,25-二羟基维生素D₃)的光化反应前体. 3-苄基保护的薯蓣皂甙元经还原开E/F环产生3,16,26-胆甾三醇-3-苄醚(5). 除去化合物5 C-16羟基后, 其C-26羟基经消除和羟基化反应转移到C-25位. 目标分子A/B环结构单元通过薯蓣皂甙元A/B环的官能团转化被构筑. 按照已知的光化反应, (1S,3R)-胆甾-5,7-二烯-1,3,25-三醇能被转化成为1α,25-二羟基维生素D₃.     

哒嗪酮类α1-肾上腺素受体拮抗剂的合成和生物活性研究

将苯(氧)乙胺和苯氧烷胺类α₁-肾上腺素受体拮抗剂中的苯(氧)乙胺、苯氧烷胺片段引入哒嗪酮类化合物中, 设计、合成了30个新的含哒嗪酮环的α₁-肾上腺素受体拮抗剂. 所有新化合物的结构均经¹H NMR, IR, HRMS确证. 生物活性测试表明28个目标物对α₁-肾上腺素受体有较好的拮抗作用(pA₂＞6.00), 化合物6o, 6p, 6q, 6v, 6x, 6y, 10c, 10d的pA₂值＞7.00.     

重氮化合物与醇的插入反应合成α-烷氧基-β-二羰基化合物

研究了在过渡金属配合物催化下α-重氮-β-二羰基化合物与醇的插入反应, 考察了重氮化合物的结构、醇的结构、催化剂的性质、反应溶剂和反应温度对这一反应的影响. 发现当重氮化合物与甲醇的物质的量比为1∶10, 1 mmol% Rh₂(OAc)₄为催化剂和回流的苯的条件下, 反应能够以高的化学产率生成α-甲氧基-β-二羰基化合物. 手性醇衍生的重氮乙酰乙酸酯反应的产物中两种非对应异构体的比例为3∶2～1∶1.     

新手性配体(QN)2AQN的合成及其催化肉桂酸甲酯的不对称氨羟化反应研究

在AlCl₃和多聚磷酸的存在下, 以邻苯二甲酸酐和对二氟苯为原料, 通过Friedel-Crafts和环化反应, 用改进的方法以60%的产率生成1,4-二氟蒽醌. 然后通过奎宁锂与1,4-二氟蒽醌的亲核取代反应得到新型手性配体(QN)₂AQN, 产率85%. 在氧化-供氮试剂N-氯代氨基甲酸苄酯存在下, (QN)₂AQN与OsO₄原位生成的催化剂在五种肉桂酸甲酯的不对称氨羟化反应中表现出优异的对映选择性(90%～96% ee)和一般至优秀的区域选择性(75∶25～98∶2), 产率50%～70%, 高于文献报道的结果. 该手性配体易于合成, 成本低廉, 用于催化不对称氨羟化反应, 可以制备光学活性的α-氨基酸酯类化合物.     

La2-xBixCuO4阴极材料的合成与电化学性质

采用甘氨酸-硝酸盐法合成了固体氧化物燃料电池阴极材料La_2-xBi_xCuO₄（x=0、0.05、0.10）,并利用X射线衍射（XRD）对材料的物相进行分析。结果表明,La_2-xBi_xCuO₄形成单一的类钙钛矿结构氧化物,且晶胞体积随着铋掺杂量的增加而增大。在950℃烧结24 h过程中,La_2-xBi_xCuO₄不与电解质Sm_0.2Ce_0.8O_1.9（SDC）发生反应,表明这种电解质材料具有良好的高温化学相容性。电导率测试结果表明Bi的掺入显著提高了材料电导率。程序升温脱附测试结果表明,铋的掺杂显著增强了材料的表面氧吸附能力。不同氧分压下的交流阻抗谱测试结果表明,La_1.9Bi_0.1CuO₄阴极在700℃空气中的极化电阻为0.26 Ω·cm²,以电解质SDC支撑的单电池NiO-SDC/SDC/La_1.90Bi_0.10O₄在700℃的最大输出功率密度为308 mW·cm^-2,电极反应的速控步骤为氧分子的扩散与表面吸附过程。     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.