钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

Ba0.4Sr0.6Co1-xFexO3-δ系阴极材料的制备和表征

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ(x=0.0～0.8)系列粉体。利用XRD和SEM对材料的结构和微观形貌进行分析,用直流四端子法测量了烧结陶瓷体在中温(450～800 ℃)范围内的电导率。结果表明,制备的样品为单一钙钛矿相,随着Fe含量增加,XRD衍射峰值向高角度方向稍有偏移。电导率随着温度及Fe含量的变化出现极大值,在x＜0.2时,Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ系列烧结体在中温(450～800 ℃)区的电导率,随Fe掺入量的增大而增大,x=0.2样品的电导率最高,800 ℃时达244.7 S·cm^-1,远超过文献报道值,进一步增大Fe含量导电性能变差。     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

凝胶自燃法合成LaxSr1-x CoyFe1-y O3-α纳米粉体

用凝胶自燃法制备了La_xSr_1-x Co_yFe_1-y O_3-α纳米粉体，研究了粉体的元素组成和掺杂性能，表征了粉体的晶相结构，测试了其粒度和形貌。结果表明应用凝胶自燃工艺合成的La_xSr_1-x Co_yFe_1-y O_3-α粉体材料粒子大小非常均匀，元素掺杂性能好，晶相单一，不需经高温热处理便能直接形成钙钛矿型结构。     

La1-xCaxFeO3-δ系阴极材料的GNP法合成及电性能研究

采用甘氨酸-硝酸盐(GNP)法合成了LaFeO₃及La_1-xCa_xFeO_3-δ(x=0.1～0.5)系列粉体，用TG-DTA、XRD、TEM、SEM等对产物形成过程及微结构进行了表征。结果表明，所合成的系列样品均形成钙钛矿结构的单相固溶体。在x≤20mol%的Ca含量范围内，产物为正交钙钛矿结构；当x>30mol%时，转变为立方钙钛矿相。相同条件下产物的衍射峰强度、晶胞体积及晶粒尺寸都随Ca含量的增大而减小。采用直流四端子法测量了烧结体在中温(450～800 ℃)区的电导率。掺杂使样品导电能力显著增强，电导率随Ca²⁺掺入量的增大先增大后减小，La_0.6Ca_0.4FeO_3-δ样品的电导率最高。在低温段，各样品的导电行为符合小极化子导电机制，导电活化能为13.67～22.70 kJ·mol^-1。     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La_1-xCa_xMnO₃(x=0~0.4)纳米颗粒, X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高, 颗粒平均粒径约40 nm。在0.1 mol·L^-1 KOH水溶液中进行的氧还原电催化性能测试显示, La_0.7Ca_0.3MnO₃样品催化活性最高, 表观电子转移数接近4, 还原电流密度与Pt/C催化剂相当, 而催化稳定性优于Pt/C。进一步研究了La_1-xCa_xMnO₃样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响, 结果表明当x=0.3时, 催化剂中Mn处于混合价态, Mn-O键长适中, 最有利于电催化反应。     

LiNi1-xMxVO4的红外光谱和拉曼光谱研究

The vanadates of LiNi_1-xM_xVO₄(M=Fe,Co,Ni) containing VO₄ tetrahedrons were synthesized by soft chemical method through a new mild liquid route. The samples sintered at 450℃ for 3h and at 650℃ for 3h are named for LT-LiNiVO₄ and for MT-LiNi_1-xM_xVO₄ respectively. All of the products were measured by X-ray diffraction, IR and Raman spectra respectively. In comparison with IR spectra of V₂O₅ and NiO, the LT-LiNiVO₄ has a strong and broad IR absorption band of VO₄ tetrahedrons located at 600～850cm^-1 with three small splitting peaks corresponding to the asymmetry stretching vibrations of V-O bonds. The results of IR and Raman spectra for MT-LiNi_1-xM_xVO₄ show that the cations of Ni²⁺, Co²⁺, Fe²⁺ have the influences on the frequency shifts of the V-O vibrations.     

复合氧化物LaxSr1-xFe1-yNiyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧法,制备纳米晶体LaxSr1-xFe1-yN iyO3,并对其进行了XRD、SEM、EDS结构分析。制备了双功能氧电极,在通氧或不通氧的条件下测试了循环伏安曲线。合成的LaxSr1-xFe1-yN iyO3复合氧化物,在汞灯激发光源下,对5种有机染料进行了脱色催化降解反应;利用红外、紫外-可见以及人工神经网络光度法研究LaxSr1-xFe1-yN iyO3的催化性能。结果表明:LaxSr1-xFe1-yN iyO3(x=0.3,0.7;y=0.1,0.25,0.6)复合氧化物具有较强光催化特性,为动力学一级反应。     

双钙钛矿Sr_2FeMn_(1-x)Co_xO_6催化剂的制备及其催化性能

通过溶胶凝胶法制备了一系列双钙钛矿催化剂Sr_2FeMn_(1-x)Co_xO_6(x=0.1,0.3,0.5,0.7,0.9),其结构经XRD,BET,H_2-TPR和SEM表征。以催化甲烷燃烧为模板反应,考察掺杂不同量Co~(2+)对Sr_2FeMn_(1-x)Co_xO_6催化性能的影响。结果表明:催化剂经800℃焙烧后可形成完整的双钙钛矿晶型,且Co离子掺杂量不同其催化活性不同,当Co离子掺杂量为0.3时,催化剂Sr_2FeMn_(0.7)Co_(0.3)O_6具有较高的催化活性,样品比表面积为9m~2·g~(-1),起燃温度T_(10%)为442℃,T_(90%)为654℃,Fe~(3+)、Mn~(2+)、Co~(2+)之间有一定协同作用。     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La1-xCaxMnO3(x=0~0.4)纳米颗粒,X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高,颗粒平均粒径约40 nm。在0.1 mol.L-1KOH水溶液中进行的氧还原电催化性能测试显示,La0.7Ca0.3MnO3样品催化活性最高,表观电子转移数接近4,还原电流密度与Pt/C催化剂相当,而催化稳定性优于Pt/C。进一步研究了La1-xCaxMnO3样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响,结果表明当x=0.3时,催化剂中Mn处于混合价态,Mn-O键长适中,最有利于电催化反应。     

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

Mn掺杂Ce0.7Zr0.3O2催化剂同时去除碳烟和氮氧化物的性能

采用柠檬酸络合燃烧法制备了一系列x%Mn/Ce0.7Zr0.3O2(x=0,5,10,15,30,50)复合金属氧化物催化剂,对其同时去除柴油机尾气中碳烟颗粒物(PM)和氮氧化物(NOx)反应的催化活性进行了评价,并采用XRD、低温氮吸附-脱附、H2-TPR、O2-TPD和原位漫反射红外光谱(in situ DRIFTS)等技术对催化剂的性能进行了表征。结果表明,不同含量Mn掺杂入铈锆固溶体中均形成了三元固溶体催化剂,在同时去除PM和NOx的催化反应中,固溶体催化剂的催化活性与其氧化能力直接相关。其中30%Mn/Ce0.7Zr0.3O2催化剂具有较好的同时去除PM和NOx的催化活性,催化去除PM的Ti和Tm分别为298和504℃,NO的转化率达到30.6%。结合O2-TPD和原位红外结果可知,30%Mn/Ce0.7Zr0.3O2表面吸附的超氧物种(O2-)及其与NO反应生成的硝酸盐物种(NO3-)是同时去除PM和NO反应的主要活性物种,进而指出PM和NO在30%Mn/Ce0.7Zr0.3O2表面反应过程中形成了异氰酸盐(-NCO)中间物种,在原位红外实验的基础上提出了30%Mn/Ce0.7Zr0.3O2复合氧化物催化剂同时去除PM和NOx的反应机理。     

功能化ZnxCd1-xS纳米晶的制备及其光学性能的研究

以氯化锌、氯化镉和硫化钠为原料，采用巯基乙醇为表面修饰剂，H₂O/DMF为溶剂，制得未团聚且分散均匀的纳米晶溶液，同时得到表面富含羟基基团不同锌镉组成的复合Zn_xCd_1-xS纳米晶。利用FTIR、EDS、UV-Vis、XRD、荧光光谱(PL)考察了复合纳米晶结构和光学性能的关系，并利用紫外灯摄像技术对Zn_xCd_1-xS纳米晶的光致发光性能进行     

钙钛矿型La1+X/2Sr1-x/2Co1-xCuxO3催化CO氧化活性与表征

The catalytic activity and the reactive properties of perovskite-type oxides catalysts La(1+x/2)Sr(1-x/2)Co1-xCuxO3 for CO oxidation reaction were investigated. Results showed that the catalytic activity for CO oxidation reached to a maximum when x＝0.4. The temperature for complete CO oxidation under atmospheric and experimental conditions was 168℃. According to the stoicheometry of catalyst, all catalysts were oxygen defect compounds. The active oxygen species on this catalyst was the adsorbed oxygen which was adsorbed on the surface lattice oxygen defect. It was also found that Co4+ existed in the catalysts and the sufrace active oxygen species was caused by the Co4+. It was concluded that CO oxidation reaction on this catalyst was carried out by the valence change between Co3+ and Co4+ which was adjusted by the adsorbed oxygen.     

Syntheses，Structures and Properties of Some New Composition Perovskite Compounds：Sr_（0．6）Bi_（0．4）FeO_（2．7），Sr_（1－x）Bi_xFeO_（3－y） and Ba_（1．5）Pt_（0．5）Mn_2O_6

Ｓｙｎｔｈｅｓｅｓ，ＳｔｒｕｃｔｕｒｅｓａｎｄＰｒｏｐｅｒｔｉｅｓｏｆＳｏｍｅ　ＮｅｗＣｏｍｐｏｓｉｔｉｏｎＰｅｒｏｖｓｋｉｔｅＣｏｍｐｏｕｎｄｓ：Ｓｒ_（０．６）Ｂｉ_（０．４）ＦｅＯ_（２．７），Ｓｒ_（１－ｘ）Ｂｉ_ｘＦｅＯ_（３－ｙ）　ａｎｄ　Ｂａ...