环保增塑剂柠檬酸三(2-乙基)己酯的合成

以柠檬酸和2-乙基己醇为原料,用结晶硫酸高铈为催化剂合成环保增塑剂柠檬酸三(2-乙基)己酯,考察了反应温度、催化剂用量、醇酸摩尔比、反应时间等因素对反应结果的影响,对合成的产品进行了红外光谱分析。实验结果表明,硫酸高铈催化合成柠檬酸三(2-乙基)己酯的最佳反应条件为n(2-乙基已醇)∶n(柠檬酸)=3.60∶1,催化剂用量为柠檬酸质量的1.5%,反应时间为90 m in,反应温度为150℃~160℃,在最佳反应条件下,柠檬酸三(2-乙基)己酯收率在98%以上。     

金属化合物催化的1,1′-联二萘酚-4,4′-二乙酸酯和二(2-乙基己醇)碳酸酯的酯交换

芳香族聚碳酸酯性能优良,其中双酚-A型聚碳酸酯是应用广泛的工程塑料,通常采用光气法或酯交换法来制备,但芳香双羟基化合物与二烷基碳酸酯的酯交换反应速度十分缓慢,需要使用催化剂,且反应温度较高,反应过程伴随着复杂的副反应。本文用金属化合物作催化剂进行1,1′-联二萘酚-4,4′-二乙酸酯和二(2-乙基己醇)碳酸酯的酯交换反应,评价了不同金     

聚[2-(4-苯基偶氮苯氧基)乙基丙烯酸酯]的合成及光响应性能研究

从4-羟基偶氮苯出发,依次与2-氯乙醇、丙烯酰氯反应,合成了2-(4-苯基偶氮苯氧基)乙基丙烯酸酯(PAPEA)。接着以PAPEA为单体,二硫代苯甲酸异丁腈酯(CPDB)为链转移剂,偶氮二异丁腈(AIBN)为引发剂,利用可逆加成-断裂链转移(RAFT)聚合法合成了聚[2-(4-苯基偶氮苯氧基)乙基丙烯酸酯](PPAPEA)均聚物,同时考察了反应时间、引发剂和链转移剂浓度等因素对聚合反应的影响。利用FT-IR、1H-NMR和GPC等对单体和聚合物的结构进行了表征,并利用UV对聚合物的光响应性能进行了测试。结果表明,PAPEA的聚合反应动力学曲线呈良好的线性关系,分子量分布较窄(小于1.3);均聚物在紫外光照下的异构化速率随分子量的增大而减缓,而其在自然光下的回复速率变化不大。     

氯代烷基膦酸二(2-乙基己基)酯萃取稀土的结构性能研究

研究了五个具有不同结构的烷基膦酸二(2-乙基己基)酯,即氯甲基膦酸二(2-乙基己基)酯CH_2ClP(O)(OC_8H_(17-i)_2(1)、β-氯乙基膦酸二(2-乙基己基)酯 ClCH_2CH_2P(O)(OC_8H_(17-i)_2(2)、α-氯乙基膦酸二(2-乙基己基)酯 CH_3CHCIP(O)(OC_8H_(17-i))_2(3)、与相应未取代的甲基膦酸二(2-乙基己基)酯CH_3P(O)(OC_8H_(17-i))_2(4)、乙基膦酸二(2-乙基己基)酯C_2H_5P(O)(OC_8H_(17-i))_2(5),在硝酸体系中对镧系元素的萃取分离性能及其规律,制备了它们的配合物,并用红外光谱和~(31)P核磁共振谱探讨萃取剂及其配合物的结构。     

聚2-丙烯酰氧乙基二茂铁甲酸酯的合成及性能

以二茂铁甲酸(FCA)和2-羟乙基丙烯酸酯(HEA)为反应物、以二环己基碳二亚胺(DCC)为脱水剂、以对二甲氨基吡啶(DMAP)为催化剂通过酯化反应合成并表征了2-丙烯酰氧乙基二茂铁甲酸酯(AEFC).然后以AEFC为单体、3种不同溴代烷为引发剂、溴化亚铜(Cu Br)和2,2-联吡啶(bpy)为催化体系、甲苯为溶剂在100℃下通过ATRP方法合成并表征了聚2-丙烯酰氧乙基二茂铁甲酸酯(PAEFC).这3种引发剂分别为:溴代乙酸乙酯(EBr A)、2-溴丙酸甲酯(2-MBP)和2-溴异丁酸乙酯(EBi B),同时还比较了3种引发剂对聚合物动力学的影响,结果表明EBr A为引发剂时AEFC的聚合过程不是以一个"活性"/可控的方式进行的,而2-MBP和EBi B为引发剂时聚合过程是以一个"活性"/可控的方式进行的,但是2-MBP的可控性较EBi B差.另外还研究了EBi B为引发剂时,EBi B的用量对聚合过程的影响,结果表明[AEFC]∶[EBi B]=100∶1时聚合过程的可控性较高.催化剂的用量对聚合过程的影响研究表明当[AEFC]∶[Cu Br]=100∶2时聚合过程的可控性较高.聚合物的热力学性能表明其有较低熔点160.6℃,热分解焓变为9541 J/g,较高的分解温度200~460℃.     

苯甲酰甲酸酯/2959光引发剂的合成与性能研究

本工作以苯甲酰甲酸(BF)和2-羟基-2-甲基-对羟乙基醚基苯基丙酮(2959)为原料,通过酯化反应合成了一种光引发剂BF-2959,采用紫外、红外、核磁共振、元素分析等手段对其进行了表征。研究了光引发剂BF-2959的合成条件,得到最佳实验条件:以甲苯为溶剂,反应时间6h,反应温度105℃,以甲烷磺酸为催化剂,苯甲酰甲酸与2959的物质的量投料比为1∶1.1,产率为92.1%;产物为无色透明液体,与树脂的相容性较好,紫外最大吸收峰在246.1nm处。在涂膜光固化测试中,用4%的BF-2959引发B-206聚氨脂和TMPTA单体聚合,转化率为93%。     

具有阳离子表面活性ATRP引发剂的合成

以2-溴异丁酰溴、2-溴乙醇、6-氯-1-己醇及N,N-二甲基正十二烷基胺为主要原料,分别通过两步或三步反应合成了具有阳离子表面活性的原子转移自由基聚合(ATRP)引发剂——N-[2-(2-溴-2-甲基丙酰氧基)乙基]-N,N-二甲基正十二烷基溴化铵或N-[6-(2-溴-2-甲基丙酰氧基)己基]-N,N-二甲基正十二烷基碘化铵,其结构经1H NMR,13C NMR,IR和元素分析表征。     

二-(1-甲基-1-七氟异丙基)五氟丙基过氧化二碳酸酯的合成

报道了一个可能的自由基前体——二-(1-甲基-1-七氟异丙基)五氟丙基过氧化二碳酸酯(1)的合成方法及其特性. 以全氟2-甲基-3-戊酮(2)为原料, 与甲基碘化镁反应后所得到的醇再与光气进行氯甲酰化反应, 随后与过氧化钠的过氧化反应后, 以17%的总产率首次合成了目标化合物.     

温度和pH值双敏感的生物相容性三嵌段共聚物聚(2-乙基-2- 唑啉)-b-聚(ε-己内酯) -b-聚(L-谷氨酸)的合成和表征

研究了由温敏的聚(2-乙基-2-噁唑啉)和pH值敏感的聚(L-谷氨酸)组成的三嵌段共聚物,聚(2-乙基-2-噁唑啉)-b-聚(ε-己内酯)-b-聚(L-谷氨酸)的合成方法,(1)以对甲苯磺酸甲酯为引发剂引发2-乙基-2-噁唑啉进行正离子开环聚合反应,得到了羟基封端的聚(2-乙基-2-噁唑啉)(PEOz-OH);(2)以PEOz-OH为引发剂,以辛酸亚锡为催化剂,在氯苯中合成了PEOz-b-聚(ε-己内酯)两嵌段共聚物(PEOz-b-PCL-OH);(3)将PEOz-b-PCL-OH末端的羟基转换为氨基,得到氨基封端的两嵌段共聚物(PEOz-b-PCL-NH2);(4)以PEOz-b-PCL-NH2为引发剂引发γ-苄基-L-谷氨酸-N-羧酸酐(BLG-NCA)开环聚合,得到了PEOz-b-PCL-b-聚(γ-苄基-L-谷氨酸)(PEOz-b-PCL-b-PBLG)三嵌段共聚物;(5)以HBr的醋酸溶液为脱保护剂脱去苄基保护基,得到PEOz-b-PCL-b-聚(L-谷氨酸)(PEOz-b-PCL-b-PLGlu)三嵌段共聚物.采用1H-NMR、GPC和FT-IR表征了各步聚合物的结构、分子量和分子量分布.     

温度和pH值双敏感的生物相容性三嵌段共聚物聚(2-乙基-2-噁唑啉)-b-聚(ε-己内酯)-b-聚(L-谷氨酸)的合成和表征

研究了由温敏的聚(2-乙基-2-噁唑啉)和pH值敏感的聚(L-谷氨酸)组成的三嵌段共聚物,聚(2-乙基-2-噁唑啉)-b-聚(ε-己内酯)-b-聚(L-谷氨酸)的合成方法,(1)以对甲苯磺酸甲酯为引发剂引发2-乙基-2-噁唑啉进行正离子开环聚合反应,得到了羟基封端的聚(2-乙基-2-噁唑啉)(PEOz-OH);(2)以PEOz-OH为引发剂,以辛酸亚锡为催化剂,在氯苯中合成了PEOz-b-聚(ε-己内酯)两嵌段共聚物(PEOz-b-PCL-OH);(3)将PEOz-b-PCL-OH末端的羟基转换为氨基,得到氨基封端的两嵌段共聚物(PEOz-b-PCL-NH2);(4)以PEOz-b-PCL-NH2为引发剂引发γ-苄基-L-谷氨酸-N-羧酸酐(BLG-NCA)开环聚合,得到了PEOz-b-PCL-b-聚(γ-苄基-L-谷氨酸)(PEOz-b-PCL-b-PBLG)三嵌段共聚物;(5)以HBr的醋酸溶液为脱保护剂脱去苄基保护基,得到PEOz-b-PCL-b-聚(L-谷氨酸)(PEOz-b-PCL-b-PLGlu)三嵌段共聚物.采用1H-NMR、GPC和FT-IR表征了各步聚合物的结构、分子量和分子量分布.     

Conversion of bis(trichloromethyl) carbonate to phosgene and reactivity of triphosgene, diphosgene, and phosgene with methanol(1)

Triphosgene was decomposed quantitatively to phosgene by chloride ion. The reaction course was monitored by IR spectroscopy (React-IR), showing that diphosgene was an intermediate. The methanolysis of triphosgene in deuterated chloroform, monitored by proton NMR spectroscopy, gave methyl chloroformate and methyl 1,1, 1-trichloromethyl carbonate in about a 1:1 ratio, as primary products. The reaction carried out in the presence of large excess of methanol (0.3 M, 30 equiv) was a pseudo-first-order process with a k(obs) of 1.0 x 10(-)(4) s(-)(1). Under the same conditions, values of k(obs) of 0.9 x 10(-)(3) s(-)(1) and 1.7 x 10(-)(2) s(-)(1) for the methanolysis of diphosgene and phosgene, respectively, were determined. The experimental data suggest that, under these conditions, the maximum concentration of phosgene during the methanolysis of triphosgene and diphosgene was lower than 1 x 10(-)(5) M. Methyl 1,1,1-trichloromethyl carbonate was synthesized and characterized also by the APCI-MS technique.     

CONDENSATION REACTION OF 1-OXO-4-CHLOROCARBONYL-1-PHOSPHA-2,6,7-TRIOXABICYCLO[2.2.2]OCTANE WITH N-t-BUTYL-N-BENZOYLHYDRAZINE

Abstract

1-Oxo-4-chlorocarbony1-1-phospha-2,6,7-trioxabicyclo[2.2.2]octane (5) was obtained from phosphorus oxychloride. Benzyl chloroformate was synthesized by the reaction of benzyl alcohol and triphosgene in good yield for the first time. N-r-Butyl-N-benzoylhydrazine(II) was prepared in a new and convenivent procedure with good yield. The reaction of 5 and II proceeded smoothly in the presence of sodium carbonate and afforded the desired compound 13 in good yield, while in the presence of triethylamine, the elimination of butyl was observed and afforded the compound 12.     

A New Method for the Synthesis of Oxadiazine Insecticide Indoxacarb

9‐Fluorenylmethoxycarbonyl was a good protecting group in the field of chemical industry. In the present paper, a new approach for the synthesis of oxadiazine insecticides indoxacarb used 9‐fluorenylmethoxycarbonyl as protected group, and triphosgene for chloroformylation. A convenient synthesis of 9‐fluorenylmethoxycarbonylhydrazine can be achieved by the nucleophilic substitution reaction of 9‐fluorenylmethyl chloroformate and hydrazine hydrate. 4a‐Methyl‐2‐(9‐fluorenylmethyl)‐7‐chloro‐indeno [1,2e][1,3,4]oxadia zine‐2,4a (3H,5H)‐dicarboxylate can be produced via ketone ‐hydrazine crosslink reaction and cyclization. A preparation of carbamic acid‐(chlorocarbonyl)‐[(4‐trifluoromethoxy) phenyl] me ester can be obtained by the chloroformylation of triphosgene. Finally, the deprotection of 9‐fluorenylmethoxy carbonyl and condensation with carbamic acid‐(chlorocarbonyl)‐[(4‐trifluoromethoxy) phenyl] me ester can afford indoxacarb in good yield. A new method for the synthesis of oxadiazine insecticides indoxacarb used 9‐fluorenylmethoxycarbonyl‐protected group to produce 9‐?fluorenylmethoxycarb?onylhydrazine, then through the ketone–hydrazine crosslink reaction, cyclization, deprotection, chloroformylation, and condensation in good yield.     

相转移催化合成对甲氧基肉桂酸-2-乙基己酯的研究

对甲氧基肉桂酸 2 乙基己酯是一种有效的ＵＶＢ防晒剂[1 ,2 ] ,一般采用Ｃｌａｉｓｅｎ Ｓｃｈｍｉｄｔ缩合反应制得[3] ,但由于催化剂ＫＯＨ处于水相 ,对反应物不能充分起到催化作用导致产率较低[4] 。我们利用乙二醇 (ＰＥＧ)为相转移催化剂合成立体专一的反式对甲氧基肉桂酸 2 乙基己酯 ,产率提高到 72 .5 %。合成路线如下 :1　实验部分1 .1　仪器与试剂ＢＩＯ ＲＡＰＦＴ45 0红外光谱仪 ,用液膜法测试 ;Ｂｒｕｒｅｒ ＡＭ 30 0超导核磁共振仪 (溶剂ＤＣ Ｃｌ3) ;ＭＡＴ/44Ｓ ,ＧＣ ＭＳ型色质联用谱仪 ;试剂均为分析纯 ,上海化学试剂…     

室温下三光气作环合剂合成5-取代-1,3,4-噁二唑-2-酮类化合物

1,3,4-噁二唑具有抗菌,抗肿瘤,抗惊厥等生物活性~([1-6]),在药物化学方面具有重要的理论意义和实际应用价值.1,3,4-噁二唑类材料具有优良的荧光性和闪烁性和优异的电子传输性能,以及特殊的稳定性和良好的耐热性,被认为是下一代显示器件中载流子输送的首选材料~([7-8]).     

Facile and selective synthesis of chloronicotinaldehydes by the Vilsmeier reaction

Eleven enamides were prepared by adopting different procedures. The various enamides prepared were subjected to Vilsmeier reaction using (i) POCl₃/DMF; (ii) diphosgene/DMF; (iii) triphosgene/DMF leading to the formation of various multisubstituted chloronicotinaldehydes. Studies carried out indicate that Vilsmeier reagent concentration and the replacement of POCl₃ by diphosgene or triphosgene, provides excellent selectivity and higher yields. Under modified reaction conditions one can get only chloronicotinaldehydes and not the chloropyridines as products. The various advantages in using diphosgene and triphosgene are illustrated. The mechanism of formation of chloronicotinaldehyde was discussed.     

HEH/EHP在中空纤维膜器中萃取钕、钐及传质研究

２－乙基己基膦酸单２－乙基己基酯（ＨＥＨ／ＥＨＰ,ＨＬ）是广泛用于稀土分离湿法冶金的有效萃取剂［１～３］．未氨化的ＨＥＨ／ＥＨＰ在中空纤维膜（ＨＦＭ）中萃取稀土元素的机理和控制模式已有报道［４,５］,但未氨化的ＨＥＨ／ＥＨＰ对轻、中稀土的萃取能力较弱...     

A Convenient Synthesis of Chiral Oxazolidin-2-Ones and Thiazolidin-2-Ones and an Improved Preparation of Triphosgene

Oxazolidin-2-ones and thiazolidin-2-one are conveniently prepared by condensation of L-serine, L-threonine and L-cysteine, respectively with triphosgene. The corresponding methyl esters may be subsequently obtained by quenching the reaction mixture with methanol, without prior need for the isolation of the free acids. An improved procedure for preparation of triphosgene using an internal cooling system is described.     

One-dimensional hierarchical layered KxMnO2 (x < 0.3) nanoarchitectures: synthesis, characterization, and their magnetic properties

One-dimensional (1D) hierarchical nanostructures of ultralong layered K(x)MnO(2) (x < 0.3) bundles with diameters 50-100 nm and lengths up to 50-100 microm have been successfully prepared by a PEG-assisted hydrothermal method based on the reaction of KMnO(4) with 2-ethylhexanol. The obtained samples ascribe to the monoclinic phase and exhibit ferromagnetic behaviors below 32 K and paramagnetic behaviors above 32 K, which may make this system a promising base material for magnetic devices. A series of contrastive experiments have illustrated that 2-ethylhexanol, PEG 400, KOH, and reaction time play an important role in the synthesis of the nanobundles. A possible growth mechanism has been proposed.     

α-(2-噻唑基脲基)膦酸二苯酯的合成

报道了一种简便的合成取代脲基膦酸酯的通用的新方法。在二氯甲烷中,三乙胺为缚酸剂的条件下,α-氨基膦酸二苯酯与三聚光气反应形成α-异氰酸基膦酸酯2,2不经分离,直接与2-氨基(苯并)噻唑加成得到α-(2-噻唑基脲基)膦酸二苯酯3,产率55.0%-88.9%。