Ce0.35Zr0.55La0.10O1.95对低贵金属Pt-Rh型三效催化剂性能的影响

采用共沉淀技术制备了Ce0.35Zr0.55La0.10O1.95固溶体, 其织构和结构性能以及氧化还原性能分别采用BET、XRD和程序升温(TP)技术进行了表征. 制备了低贵金属Pt-Rh型三效催化剂, 考察了Ce0.35Zr0.55La0.10O1.95对催化剂性能的影响. XRD和BET的结果表明, 经600 ℃焙烧5 h后, Ce0.35Zr0.55La0.10O1.95具有与Ce0.50Zr0.50O2相似的立方结构和高的比表面积；经1000 ℃焙烧5 h后, 仍能保持稳定的立方结构和47.25 m2•g−1的比表面积, 表现出优越的织构性能和高的热稳定性. H2-TPR和O2-TPO的结果表明, Ce0.35Zr0.55La0.10O1.95具有比Ce0.50Zr0.50O2更好的氧化还原性能. 和含Ce0.50Zr0.50O2的催化剂相比, 含Ce0.35Zr0.55La0.10O1.95的催化剂具有较宽的工作窗口, 优越的低温起燃性能, 较强的水气变换能力；催化剂经1000 ℃高温水热老化5 h后, 仍具有良好的催化活性, 表现出了优异的抗老化性能.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体.采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂.BET结果显示,将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积.TPR结果显示,载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能.XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化.特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时,Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33, 用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体. 采用这些固溶体作载体, 以Fe2O3为活性组分, 用浸渍法制备了一系列催化剂. BET结果显示, 将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积. TPR结果显示, 载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能. XRD结果表明, Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况, 老化前后催化剂的晶相结构基本无明显变化. 特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时, Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n（Ce）／n（Zr）比为0．67／0．33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体,采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂,BET结果显示,将适量Ce0.67Zr0．33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积,TPR结果显示,载体中引入适量的Ce0．67Zr0.33O2可以改善催化剂的氧化还原性能,XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化,特别是当载体中m（Ce0.67Zr0.33O2）：m（Al2O3）的值为1：2时,Fe2O3／CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能。     

负载型Pd三效催化剂：载体CeO2-ZrO2-BaO的制备及催化性能

制备了不同BaO含量的CeO2-ZrO2储氧材料,并以此材料为载体浸渍H2PdCl6制得三效催化剂.结果表明,不论新鲜还是1 000 ℃老化状态下,以10%BaO添加CeO2-ZrO2储氧材料制备的Pd三效催化剂活性最佳,起燃和完全转化温度最低.XPS结果证实,10%BaO添加.通过稳定PdO活性组分并改变其电子环境使得催化剂有最佳活性.而随着BaO含量持续增加,Pd活件组分相对处于较氧化状态.储氧量、低温N2吸附-脱附测试以及XRD测试结果均表明10%BaO添加的材料储氧量,比表面积以及孔容均最大,而且有适应三效催化的孔径.这些结果均有助于以其制备的Pd三效催化剂获得更好的活性以及热稳定性.     

Pd/γ-Al2O3三效催化剂中CeO2-ZrO2-La2O3的作用

用浸渍法制备了CeO2-ZrO2-La2O3复合氧化物,用XRD,TG-DTA,拉曼光谱、H2-TPR和BET表面积测定等方法对合成的样品进行了表征,研究了在单钯Pd/γ-Al2O3催化剂中添加CeO2-ZrO2-La2O3对催化剂活性和热稳定性的影响.结果表明,在Pd/γ-Al2O3中加入三元复合氧化物有利于提高三效催化剂的热稳定性,有利于阻止γ-Al2O3在高温时的相变以稳定Al2O3结构,防止在高温条件下催化剂表面积的损失.在Pd的负载量为1 g*L-1条件下,测定了Pd/CeO2-ZrO2-La2O3/γ-Al2O3/蜂窝陶瓷催化剂对CO,C3H6和NO净化的三效活性,研究了催化剂的结构和三效催化活性之间的关系.结果表明,CeO2-ZrO2-La2O3的存在能明显提高Pd基催化剂对CO,C3H6和NO的三效净化活性,扩大催化剂的操作窗口,提高在富氧条件下对NOx的还原性能.     

Pt/CeO2-ZrO2变换催化剂的制备、表征与性能

 用共沉淀法制备了不同Ce/Zr比的CeO2-ZrO2复合氧化物,用浸渍法制备了Pt/CeO2-ZrO2水煤气变换催化剂,并对该催化剂进行了活性评价. 结果表明,与传统的Cu基低变催化剂相比,该催化剂具有操作温度范围宽和抗氧化冲击等优点,具有应用于车载重整制氢过程的潜力. 考察了温度、空速和汽/气比等条件对催化剂活性的影响,对催化剂的制备参数和工艺参数进行了研究. 结果表明,不同Ce/Zr比的Pt/CeO2-ZrO2催化剂的活性相差很大,其中Pt/Ce0.8Zr0.2O2变换催化剂活性最高. XRD结果表明,制备的Pt/Ce0.8Zr0.2O2形成了固溶体. 通过增加单位质量催化剂表面的Pt原子数可提高催化剂的活性.     

不同碱土金属掺杂对 Rh/Ce0.35Zr0.55M0.10O1.90+Pt/La-Al2O3 三效催化剂性能的影响

 采用共沉淀法制备了不同碱土金属掺杂的 Ce0.35Zr0.55M0.10O1.90 (CZM; M = Mg, Ca, Sr 或 Ba) 固溶体, 并采用 N2 吸附-脱附、储氧量测定、程序升温还原和 X 射线衍射对其进行了表征. 以 CZM 和 La-Al2O3 为载体, 制备了负载型低贵金属 Pt-Rh 三效催化剂, 并考察了其催化活性. 结果表明, 经 600 oC 焙烧 5 h 后, CZCa 样品的比表面积为 109 m2/g, 经 1 000 oC 老化 5 h 后仍有 47 m2/g. 所有新鲜样品均具有较低的还原温度和良好的还原性能. 老化后的 CZCa 仍具有较好的还原性能和较高的储氧量. 在 600 oC 下焙烧的样品均为立方晶相; 经 1 000 oC 老化 5 h 后, 只有 CZMg 发生相分离, 其余样品仍为稳定的立方晶相. 活性测试结果表明, 所有新鲜催化剂均具有良好的低温起燃性能; 经 1 000 oC 水热老化 5 h 后, 含有 CZCa 的催化剂仍具有较低的起燃温度, 表现出优异的抗老化性能.     

CeO2-ZrO2固相溶液的制备和贮氧能力的研究

二氧化铈(CeO2)是优良的催化剂和催化剂促进剂,通过引入二氧化锆(ZrO2)可以提高其热稳定性及贮氧能力.研究以硝酸铈(Ⅳ)和氯氧锆为原料,用均相沉淀法制备CeO2-ZrO2固相溶液.用X光衍射(XRD)、差热-热重分析(DSC-TGA)、BET测定法和贮氧能力测定法对制备的CeO2-ZrO2进行了表征.BET测定制备的样品比表面积可达114m2/g;XRD结果表明,均相沉淀法制备样品具有萤石结构,Ce/Zr为3∶1,450℃时即可制备出Ce0.75Zr0.25O2,800℃时,相结构稳定,TGA-DSC热分析没有出现热峰,说明样品热稳定性优良;通过100℃、200℃、400℃和800℃的氧贮存能力测定,实验结果表明,CeO2-ZrO2固体溶液的氧贮存能力随温度的升高而降低,在高温下的氧贮存能力随Zr含量的增加而增大,ZrO2的引入不但改进了CeO2的热稳定性,而且提高Ceo2样品高温下的氧贮存能力.     

CeO_2-ZrO_2-Al_2O_3稀土储氧材料制备工艺的研究

采用化学沉淀法制备了系列CeO2-ZrO2-Al2O3稀土储氧材料,并用BET,XRD和储氧性能测定等表征手段考察了陈化时间、La2O3含量、反应pH和沉淀方式等工艺因素对CeO2-ZrO2-Al2O3比表面积、储氧性能和结构的影响。结果表明:当陈化时间为12 h,反应pH=10时,掺杂2%(质量分数)La2O3的CeO2-ZrO2-Al2O3样品在老化前后均具有很高比表面积和良好的储氧性能,并且pH为影响样品比表面积及热稳定性能的主要因素。与一步法沉淀相比,二步法制得的CeO2-ZrO2-Al2O3样品具有很高的热稳定性能,1050℃老化5 h后的样品比表面积高达46.4 m2.g-1,但储氧性能略差,这与Al2O3对CeO2-ZrO2的结构影响程度有关。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.