伴随变阻尼作用的干摩擦下的车辆系统非线性动力学分析

对分段线性阻尼和干摩擦共同作用下的车辆悬挂系统进行了非线性动力学分析研究，阐述了判定系统周期运动稳定性的理论方法；利用数值模拟方法分析了具有不同阻尼参数组合的系统对简谐激励的振动响应，并分析了由干摩擦引起的粘-滑振动行为．结果表明：提高摩擦力对抑制响应有利，但车辆系统在低速下运行时会出现复杂的粘-滑振动，轮轨之间产生较大的瞬时刚性冲击；而通过增加轮对与侧架的弹性悬挂可以有效减弱这种瞬时刚性冲击．     

振动驱动移动机器人直线运动的滑移分岔

近年来,随着移动型机器人设计技术水平的不断提高,其运动形式日趋多样. 借助于仿生学的思想,模仿蚯蚓等动物的蠕动成为不少机器人设计者所追求的目标. 为了实现这一目标,学者们提出并研究了振动驱动系统. 本文研究了各向同性干摩擦下,单模块三相振动驱动系统的粘滑运动. 考虑到库伦干摩擦力的不连续性,振动驱动系统属于Filippov 系统. 基于此,运用Filippov 滑移分岔理论,分析了振动驱动系统不同的粘滑运动情况. 根据驱动参数的不同,系统运动的滑移区域被分成4 种基本情形. 对这些情形分类讨论,得到系统的6 种运动情况. 然后对这6 种运动情况进行归纳,最终得出系统一共存在4 种不同的粘滑运动,而且也解析地给出了发生这4 种粘滑运动的分岔条件. 分岔条件包含系统的3 个驱动参数,通过变化这些参数,得到了系统运动的分岔图. 借助分岔图,详细分析了随着驱动参数的变化,系统如何实现不同粘滑运动类型之间的切换,并从分岔角度给出了相应的物理解释. 最后,通过数值方法直接求解原运动方程,数值解法得到的4 种运动图像与理论分析一致,验证了系统运动分岔研究的正确性.      

受限颗粒体对制动系统非线性振动的影响

制动系统在工作时,往往受到沙粒、尘土以及磨屑等受限颗粒体的影响,这些受限颗粒体在摩擦副中的高度分布具有较强的随机性,一定程度诱发了制动系统的非线性振动. 本文中基于制动片切向振动模型,引入了新的受限颗粒体摩擦模型,提出了用波动系数来描述受限颗粒体高度分布随机性的强弱. 发现在特定参数下,当此系数为0时,制动片切向振动为周期运动;但是当此系数不为0时,制动片切向振动呈现拟周期或混沌运动,此时的切向振动分岔特性图的稳定轨道也会出现数量或分布的变化,甚至表现出混沌特性. 同一时变信号内,受限颗粒体引发制动片切向非线性振动包括发散、收敛以及拟周期运动等多种形式.      

GCr15钢-CVDCr_7C_3镀层摩擦副摩擦振动的研究

本文系统地研究了GCr15钢球-CVDCr_7C_3镀层钢盘摩擦副滑动干摩擦引起的摩擦力(切向力)振动特性及其对材料摩擦磨损性能的影响。试件系统在垂直和水平方向上均处于低刚度、小阻尼状态。试验信号由微机采集、处理并进行频谱分析。结果表明,摩擦力振动的类型与正压力有关,而与拖动速度无关;摩擦力呈周期性自持振动时具有与相对滑动速度典型的非线性关系,振动频率接近(略低)于系统在切向的固有频率,而与拖动速度无关;摩擦力呈非平稳随机振动时,振动频率与系统在法向的振动频率有关,而与系统在切向的固有频率及拖动速度都无关;摩擦偶件运动的平稳性与摩擦力振动的类型有关,而与平均摩擦系数无关;摩擦力所耗费的能量与正压力呈比例关系。     

层状边坡岩体滑动稳定的三维动力学分析

本文通过振动模拟试验探索了块体运动时滑面的摩擦特性，建立了块体运动的三维动力学方程，并探讨了层状边坡层间振动加速度在传递过程中加速度变化情况。从而可以计算出受振动影响时边坡各层间的稳定性。     

多自由度分段光滑非线性系统的近似解——中华文物龙洗的自激振动

建立了由于摩擦引起的两个弹性体之间自激振动的数学模型.利用平均法求出了由干摩擦引起的多自由度分段光滑非线性动力系统的近似解析解,分析了搓动速度、振动频率与振幅的关系曲线,相位角与搓动速度的关系曲线,分析结果与数值解基本吻合.为研究多自由度分段光滑非线性系统提供了一种有效的近似解析分析方法.     

基于Nyquist稳定判据的磨合过程稳定性研究

在销-盘摩擦磨损试验机上进行了船用柴油机缸套-活塞环摩擦配副磨合磨损试验,采集磨合过程中摩擦振动信号,应用Nyquist稳定判据,通过摩擦振动Nyquist曲线对磨合系统稳定性进行分析.结果表明:摩擦振动Nyquist曲线反映了磨合系统稳定性变化.当摩擦副磨合开始时(0～10 min),摩擦振动Nyquist曲线不包围(-1,j0)点,磨合系统处于稳定磨损阶段;在摩擦副磨合进行过程中(10～40 min),摩擦振动Nyquist曲线包围(-1,j0),磨合系统处于不稳定磨损阶段;当摩擦副达到磨合时(40 min后),摩擦振动Nyquist曲线不包围(-1,j0),磨合系统处于稳定磨损阶段.因此,磨合系统的特性可揭示磨合过程稳定性变化规律.     

基于平均法的旋转薄壁圆柱壳非线性行波振动研究

应用Donnell's简化壳理论,在考虑阻尼和几何非线性的情况下,基于平均法对旋转的薄壁悬臂圆柱壳在法向激振力作用下的非线性行波振动进行了研究.在分析过程中,首先,引入考虑阻尼及几何非线性的薄壁圆柱壳非线性波动方程,进行降阶处理后,得到模态坐标下的振动方程;其次,对模态方程进行平均化处理,确定转换矩阵,进行变量的幅值相角化,从而得到自治的标准化方程组;最后,由系统谐波共振周期解对应平均方程稳态解的原理,得到幅频特性方程.根据上述所得结果,进行了系统参数振动及稳定性研究,并进一步将结果与谐波平衡法及数值解作了比较.     

多自由度分段光滑非线性系统的近似解——-中华文物龙洗的自激振动

建立了由干摩擦引起的两个弹性体之间自激振动的数学模型. 利用平均法 求出了由干摩擦引起的多自由度分段光滑非线性动力系统的近似解析解，分析了搓动速度、 振动频率与振幅的关系曲线，相位角与搓动速度的关系曲线，分析结果与数值解基本吻合. 为研究多自由度分段光滑非线性系统提供了一种有效的近似解析分析方法.     

凸肩叶片的非线性振动特性与运动分岔

以凸肩叶片作为研究模型, 建立了考虑凸肩摩擦力, 几何大变形与阻尼的非线性振动方程.采用Galerkin法对振动方程离散化, 应用平均法对离散后模态方程组的非线性响应进行解析分析, 得到了非线性幅频特性曲线, 与数值解比较验证了解析解, 并讨论了系统周期解的稳定性. 用非线性振动理论详细研究了平均方程组的运动分岔现象, 揭示了平均方程组周期解的变化过程及其具有的非线性动力学性质. 解析结果表明, 凸肩之间的摩擦对系统第二阶非线性振动特性影响很大. 由于凸肩之间摩擦力方向的不断改变, 系统第二阶非线性幅频特性曲线不连续, 出现两个共振频域. 随着时间的推移, 系统振动的幅值会以$T/ 4$为周期在两个频域的幅频曲线上来回跳动, 这会使叶片的振动响应大幅降低.      

Dynamical analysis of axially moving plate by finite difference method

The complex natural frequencies for linear free vibrations and bifurcation and chaos for forced nonlinear vibration of axially moving viscoelastic plate are investigated in this paper. The governing partial differential equation of out-of-plane motion of the plate is derived by Newton’s second law. The finite difference method in spatial field is applied to the differential equation to study the instability due to flutter and divergence. The finite difference method in both spatial and temporal field is used in the analysis of a nonlinear partial differential equation to detect bifurcations and chaos of a nonlinear forced vibration of the system. Numerical results show that, with the increasing axially moving speed, the increasing excitation amplitude, and the decreasing viscosity coefficient, the equilibrium loses its stability and bifurcates into periodic motion, and then the periodic motion becomes chaotic motion by period-doubling bifurcation.     

Vibration analysis and active control of nearly periodic two-span beams with piezoelectric actuator/sensor pairs

The piezoelectric materials are used to investigate the active vibration control of ordered/disordered periodic two-span beams. The equation of motion of each sub-beam with piezoelectric patches is established based on Hamilton's principle with an assumed mode method. The velocity feedback control algorithm is used to design the controller. The free and forced vibration behaviors of the two-span beams with the piezoelectric actuators and sensors are analyzed. The vibration properties of the disordered two-span beams caused by misplacing the middle support are also researched. In addition, the effects of the length disorder degree on the vibration performances of the disordered beams are investigated. From the numerical results, it can be concluded that the disorder in the length of the periodic two-span beams will cause vibration localizations of the free and forced vibrations of the structure, and the vibration localization phenomenon will be more and more obvious when the length difference between the two sub-beams increases. Moreover, when the velocity feedback control is used, both the forced and the free vibrations will be suppressed. Meanwhile, the vibration behaviors of the two-span beam are tuned.     

Dynamic analysis of microrobots with Coulomb friction using harmonic balance method

In this paper, we investigate the dynamic analysis of a strongly nonlinear microrobot using a three-term harmonic balance method. The employed locomotion concept, namely “friction drive principle,” is based on the superposition of a horizontal vibration at the interface between the robot and work floor and an active variation of friction force, obtained by the vertical vibration of the base at the same interface. The equation of motion for the system reveals a parametrically excited oscillator with discontinuity for which the elastic force term is proportional to a signum function. The obtained periodic solution not only is of high accuracy, but also can predict the contribution of the friction coefficient in the average velocity of the slider. Results show that the velocity and the step efficiency of motion depend almost sinusoidally on the phase shift between the horizontal and the vertical vibration. Unlike traditional analytical techniques and in agreement with both numerical simulations and experimental results reported in the literature, the utilized method demonstrates that the maximum average velocity occurs at a phase shift that varies with respect to system’s configuration parameters. Besides, the effect of variation of different configuration parameters on the behavior of this type of microrobots has been studied and the maximum achievable performance in terms of velocity and the step efficiency has been evaluated.     

水轮发电机转子偏心引起的非线性电磁振动

由于机械和电磁相互耦合,水轮发电机的电磁振动具有强非线性特征。根据不平衡磁拉力与转子偏心的非线性函数关系,通过简化的各向同性的单圆盘转子系统,建立了水轮发电机转子电磁振动的非线性系统。利用非线性振动理论的多尺度方法,从理论上分析了该系统强迫振动的稳态响应,进而研究了水轮发电机转子偏心引起的电磁振动。研究发现不平衡磁拉力使系统的涡动频率下降,使运动的中心发生变化;并且会引起两倍转频的振动。最后用模型转子仿真试验的结果验证了这些理论分析的结论。     

Vibrational dynamics of a light body in a liquid-filled rotating cylinder

The behavior of a light free cylindrical body in a rapidly rotating horizontal cylinder containing a liquid under vibrational action (the vibration direction is perpendicular to the rotation axis) is investigated. An intense rotation of the body relative to the cavity is detected. Depending on the vibration frequency, the body rotation velocity in the laboratory reference system may be higher or lower than the cavity rotation velocity and in the resonance region they may differ by several times. The mechanism of motion generation is theoretically described. It is shown that the motion is related with the excitation of inertial oscillations of the body: the cause of the motion is an average vibrational force generated due to nonlinear effects in the Stokes boundary layer near the oscillating body. The formation of large-scale axisymmetric vortex structures periodic along the rotation axis, which appear under conditions of inertial oscillation of the body during its motion, both leading and lagging, is detected.     

振动摩擦机理及其非线性动力学特性

本文揭示了振动工况下散体物料的振动摩擦机理,给出了振动参数与土壤内摩擦力的关系曲线,并用数值试验方法模拟了复杂的振动摩擦压实过程,分别给出了振频和振幅对土壤孔隙比和轴向应力均值的关系曲线,验证了振动压实减摩机理的正确性.结果表明:松散物料在振动工况下,其颗粒间的摩擦力由静摩擦力转变为动摩擦力,随着振频和振幅的增加,摩擦阻力减小,从而土的内摩擦力减小,并且存在最优的振动强度使土壤在振动压实过程中的内摩擦力最小.建立了基于振动压路机的振动摩擦系统非线性动力学模型,利用渐进法得到了振动压实过程的共振响应和非共振响应.