辐射与发光 发光与发光器件

TN312.8 2006031822白光LED的加速老化特性=Characteristics of the acceler-ated aging white LEDs[刊,中]/林亮(北京大学物理学院,人工微结构与介观物理国家重点实验室.北京(100871)) ,陈志忠…∥发光学报.—2005 ,26(5) .—617-621对两组GaN基白光发光二极管(LED)进行了对比温度加速老化实验,环境温度分别是80 ,100 ℃。随着老化温度的升高,电流-电压(I-V)曲线的隧道电流段、扩散电流以及反向漏电电流段均增加,而串联电阻段则变化较小,这是位错密度升高和金属杂质沿着螺旋位错聚集及移动的结果;电容-电压(C-V)曲线中反向偏压下电…     

利用温变电容特性测量发光二极管结温的研究

结区的温度, 简称结温, 是发光二极管(LED) 的重要参数之一, 它对LED 器件的出光效率、光色、器件可靠性和寿命均有很大影响, 准确测量LED 器件的结温对制备LED 芯片、器件封装和应用有着重要的意义. 本文利用反向偏压下的LED的势垒电容随温度变化的特性, 提出了一种LED结温测量的新方法. 论文首先测量和分析了LED在室温下反向偏压时的电容-电压(C-V)曲线和不同反向偏压下的电容-温度(C-T)曲线, 结果表明, 在合适的偏压下, LED的电容随温度的增大而显著增加, 并呈现良好的线性关系. 在LED工作中监测其电容的变化, 并与C-T曲线进行对比, 实现了LED结温的测量, 其测量结果和传统的正向电压法的结果相对比, 两者符合较好. 最后, 利用上述方法测量了LED 在恒流和恒压条件下的结温的实时变化过程. 较传统的结温测量方法, 本方法的优点在于只须要一次定标测量, 且可实现LED在任意电压和电流下的结温测量.     

基于电容和电导特性分析GaN蓝光发光二极管老化机理

采用正向交流小信号方法测试和分析老化前后GaN发光二极管（LED）的电容-电压特性,结合串联电阻、理想因子、隧穿电流参数讨论负电容以及电导变化情况.基于L-V曲线定性分析老化前后负电容的阈值电压,老化之后样管的受主浓度降低,辐射复合概率下降,大量缺陷以及非辐射复合中心出现,对载流子俘获作用增强,造成负电容降低.反向偏压以及小正向偏压下,隧穿效应导致老化之后样管的电导增大;正向偏压大于2.2 V区域,考虑串联电阻效应,老化后样管电导减小.在分析LED电容-电压、光输出、电学特性曲线与老化机理基础上,通过实验论证以及理论解释表明,负电容以及电导特性可作为分析LED老化特性的参考依据. 关键词： GaN发光二极管 负电容 电导 老化机理     

GaN基功率LED电应力老化早期的退化特性

对InGaN/GaN多量子阱蓝光和绿光LED进行了室温900 mA电流下的电应力老化,发现蓝光LED老化到24h隧穿电流最小,绿光LED到6h隧穿电流最小;同时,两种LED的反向漏电也最小、光通量最大,随后绿光LED的反向漏电增加较快且光通量衰减较快.把热退火效应和电应力下缺陷的产生分别看成正负加速因子,绿光LED的负...     

电流拥挤效应与LED器件可靠性分析

对小功率GaN基白光LED的电流拥挤效应进行了研究,发现串联灯组(8只为一组)在经过22 V电压冲击后出现漏电失效现象。通过Pspice软件对串联LED灯组进行模拟,发现与其他样品相比,受损样品承受了更大的电压和功率;对器件加-2 V偏压,利用光发射(EMMI)显微镜对芯片表面不同量级漏电流进行定位分析比较,结果表明漏电流集中在p型扩展电极端点附近。分析认为,电压冲击的破坏路径穿过了LED的量子阱结构,而电流的不均匀分布造成了 p型扩展电极附近的电流拥挤,加剧了pn结的损伤程度,提高电流扩展的均匀性可以有效提高LED的可靠性。最后还对在正向电流-电压区域出现微分负阻特性的器件进行了失效分析。     

基于不同电压下的电致发光和红外成像的太阳能电池缺陷检测

利用不同电压下的电致发光和红外热成像技术检测太阳能电池的缺陷。正向电致发光为电子空穴的辐射复合,与太阳能电池的串联电阻和少数载流子扩散长度有关,可以检测太阳能电池的断栅、隐裂等缺陷;反向电致发光为高电场强度下载流子的带内发光,可以探测弱的线性漏电和击穿,并且弱的线性漏电只在高的反向偏压下发光。利用不同电压下的红外热成像可以检测出线性和非线性漏电,强线性漏电在正反偏压电压下均有明显发热的现象,而非线性漏电在何种偏压状态下占优势取决于漏电类型。红外热成像无法探测出第二类击穿和第三类击穿。     

Si衬底GaN基蓝光LED老化性能

报道了芯片尺寸为500μm×500μm硅衬底GaN基蓝光LED在常温下经1000h加速老化后的电学和发光性能,其光功率随老化时间的变化分先升后降两个阶段;老化后的反向漏电流和正向小电压下的电流均有明显的增加;老化后器件的外量子效率(EQE)比老化前低;老化前后EQE衰减幅度在不同的注入电流下存在明显差异,衰减幅度最小处出现在发光效率最高时对应的电流密度区间。     

GaN发光二极管表观电阻极值分析

利用正向交流(ac)小信号方法对GaN发光二极管的电容-电压特性进行测量,可以观察到GaN发光二极管中的负电容现象。利用LED串联等效电路对表观电容和表观电阻进行了测量,表观电阻-正向电压曲线出现了一个极值点。通过对相关文献分析,提出负电容现象的根本原因是在较高的正偏下微分电容dQ/dU<0;推论出pn结的微分电容先随正向偏压的增大而急剧增大,当出现复合发光后随正向偏压的增大而减小,直到随正向偏压的增大而出现负值;正向偏置电压较大时,结电导电流的变化率根据I-V特性曲线取极大值,此时微分电容由于强复合效应已快速变小,表观电阻有极大值;得到了表观电阻极大值表达式。表观电阻与正向电压曲线的极值点与理论模型相吻合,证明了该理论模型的正确性。     

晶格匹配InAlN/GaN异质结肖特基接触反向电流的电压与温度依赖关系

测量了晶格匹配InAlN/GaN异质结肖特基接触的反向变温电流-电压特性曲线,研究了反向漏电流的偏压与温度依赖关系.结果表明:1)电流是电压和温度的强函数,饱和电流远大于理论值,无法采用经典热发射模型解释;2)在低偏压区,数据满足ln(I/E)-E^1/2线性依赖关系,电流斜率和激活能与Frenkel-Poole模型的理论值接近,表明电流应该为FP机制占主导;3)在高偏压区,数据满足ln(I/E)-E^1/2线性依赖关系,电流斜率不随温度改变,表明Fowler-Nordheim隧穿机制占主导;4)反向电流势垒高度约为0.60 eV,远低于热发射势垒高度2.91 eV,表明可导位错应是反向漏电流的主要输运通道,局域势垒由于潜能级施主态电离而被极大降低.     

4H-SiC肖特基二极管的电荷收集特性

针对极端环境下耐辐照半导体核探测器的研制需求,采用耐高温、耐辐照的4H碳化硅(4H-SiC)宽禁带材料制成肖特基二极管,研究了该探测器对241Am源粒子的电荷收集效率。从电容-电压曲线得出该二极管外延层净掺杂数密度为1.991015/cm3。从正向电流-电压曲线获得该二极管肖特基势垒高度为1.66 eV,理想因子为1.07,表明该探测器具备良好的热电子发射特性。在反向偏压高达700 V时,该二极管未击穿,其漏电流仅为21 nA,具有较高的击穿电压。在反向偏压为0~350 V范围内研究了该探测器对3.5 MeV 粒子电荷收集效率,在0 V时为48.7%,在150 V时为99.4%,表明该探测器具有良好的电荷收集特性。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.