Tb3+,Eu3+单掺杂、双掺杂SrSiO3的合成、结构表征与发光性能

采用液相沉淀法合成了铽单掺杂,铕单掺杂,铽、铕双掺杂的硅酸锶发光材料。其结构经X-射线衍射表征。研究了合成样品的激发、发光光谱。研究结果表明:在254nm波长紫外光激发下,SrSiO₃:0.04Eu³⁺的发光光谱中出现4个Eu³⁺的发光峰,分别为Eu³⁺的⁵D₀→⁷F₁（588、590nm）、⁵D₀→F₂（609nm）、⁵D₀→⁷F₃（626nm）、⁵D₀→⁴F₄（651nm）跃迁峰;SrSiO₃:0.04Tb³⁺的发光光谱中出现4个Tb³⁺的发光峰,分别为Tb³⁺的⁵D4→^F₆（488nm）、⁵D₄→⁷F₅（541、548nm）、⁵D₄→⁷F₄（584nm）跃迁峰;SrSiO₃:0.04Tb³⁺,0.04Eu³⁺发光体系中,Tb³⁺的共掺杂显著增强了Eu³⁺的特征发射,存在Tb³⁺→Eu³⁺的能量传递现象,结果表明有Eu³⁺和Tb³⁺两个发光中心。     

近紫外激发具有颜色可调的Er3+/Eu3+共掺BiOCl荧光粉

本文采用固相法在500℃合成了Er³⁺/Eu³⁺共掺BiOCl 荧光粉, 并通过XRD, SEM, 吸收, 激发和发射光谱研究了其结构、形貌和发光特性. XRD 和SEM结果表明在500℃下即可成功合成纯四方相片层结构的Er³⁺/Eu³⁺共掺BiOCl荧光粉. 吸收光谱表明掺杂Er³⁺/Eu³⁺离子使BiOCl形成杂质能级; 激发光谱显示该荧光粉具有来自于基质BiOCl价带(VB)到导带(CB)跃迁的优异宽带近紫外激发特性. 在380 nm近紫外光激发下, 同时获得了Er³⁺离子和Eu³⁺离子的特征发射峰, 其中发光中心位于410 nm (²H_9/2→⁴I_15/2), 525 nm (²H_11/2→⁴I_15/2), 554 nm (⁴S_3/2→⁴I_15/2), 673 nm (⁴F_9/2→⁴I_15/2)的发射峰来自于Er³⁺离子的跃迁, 而581 nm(⁵D₀→⁷F₀), 594 nm (⁵D₀→⁷F₁), 622 nm (⁵D₀→⁷F₂), 653 nm (⁵D₀→⁷F₃), 699 nm (⁵D₀→⁷F₄)的发射峰则来自于Eu³⁺离子的跃迁. 值得注意的是, 与传统Er³⁺/Eu³⁺掺杂的材料不同, 该荧光粉还具有独特高效的紫光(Er³⁺)和长波红光(Eu³⁺)发射特性, 分析表明这与BiOCl的结构有关; 并且通过改变掺杂浓度, 实现了发光颜色由黄绿光→黄光→橙红光的调节. 研究结果表明Er³⁺/Eu³⁺共掺BiOCl荧光粉有望成为一种潜在的近紫外激发白光LED荧光粉.     

BaWO4∶Eu3+红色荧光粉的水热制备及其发光性能

采用水热法,通过变化水热反应时间制备出不同的BaWO₄∶Eu³⁺样品,利用XRD和SEM分析了样品的晶体结构和表面形貌,研究了基质晶体生长取向对BaWO₄中Eu³⁺离子特征发射的影响。实验结果表明:BaWO₄∶Eu³⁺样品在395 nm近紫外光或464 nm蓝光激发下发射578,592,612 nm的红光,其中612 nm(⁵D₀→⁷F₂)发射强度明显高于592 nm (⁵D₀→⁷F₁)。在水热温度160 ℃的情况下,所制备的样品均为四方相,不同的水热反应时间将影响晶体在各晶向的生长速度,进而影响晶体的对称性和发光性能。水热时间为10 h时的发射强度最大。     

不同退火温度下α-NaYF4:Eu3+红色荧光粉的合成与发光特性

采用溶剂热法合成了α-NaYF₄:5%Eu³⁺红色荧光粉,研究不同退火温度对荧光粉晶体结构、形貌、发光以及显色性能 (CIE)的影响。通过比较退火前后以及不同退火温度下荧光粉的发光性能,发现退火使得禁戒跃迁⁵D₀→⁷F₀发生,随着退火温度的升高,Eu³⁺所有发射峰都得到了相应的增强,并且相应的CIE更趋向于红色;但在高温退火时,纳米晶之间的团聚更加严重,而且CIE趋向于红色的速度变慢。基于非对称性比率σ的分析,认为本文中⁵D₀→⁷F₀跃迁是由于Eu³⁺占据非对称中心格位所致。     

LnP5O14晶体中Tb3+和Eu3+的发光光谱特性

本工作测量了室温下TbP₃O₁₄和EuP₅O₁₄晶体的吸收和发射光谱。根据吸收光谱和Judd-Ofelt理论计算了Tb³⁺和Eu³⁺的实验和理论的振子强度。用最小二乘法拟合实验与理论的振子强度得到唯象强度参量Ω_λ。然后计算了Tb³⁺的⁵D₃→⁷F₅,⁵D₄→⁷F₄和⁵D₄→⁷F₆以及Eu³⁺的⁵D₀→⁷F₂,⁵D₀→⁷F₄的跃迁几率和寿命。同时用时间分辨光谱测量了不同温度下相应的荧光辐射寿命。计算与实验结果基本相符。理论和实验的结果表明Tb³⁺的⁵D₃态的寿命主要取决于⁵D₃→⁵D₄和⁷F₆→⁷F₀两能级对之间的电偶极-电偶极交叉弛豫。 关键词：     

白光LED用红色荧光粉Sr2EuxGd1-xAlO5的制备及其发光性质

用高温固相反应法合成了Sr₂Eu_xGd_1-xAlO₅红色荧光粉,研究了荧光粉的晶体结构和发光性质。在紫外光和近紫外光激发下,样品的发射光谱由Eu³⁺的⁵D₀→⁷F_J(J=0,1,2,3,4) 特征发射组成,其中Eu³⁺离子的⁵D₀→⁷F₁(λ=590 nm)和⁵D₀→⁷F₂(λ=622 nm)跃迁发射的强度最大。当Eu³⁺离子的摩尔分数为 0.75时,样品的发光最强。研究结果表明,Sr₂Eu_xGd_1-xAlO₅荧光粉是一种在近紫外芯片白光LED上有应用前景的红光荧光粉。     

NaLa(MoO4)2∶Eu3+的水热调控合成与发光特性研究

采用水热法合成了不同粒径的NaLa(MoO₄)₂∶Eu³⁺微晶.通过调节乙二醇浓度和反应时间,研究了NaLa(MoO₄)₂∶Eu³⁺微晶的形貌演变过程,在水热条件下180 ℃反应16 h获得了均一梭子形NaLa(MoO₄)₂∶Eu³⁺微晶,其晶粒长度约为2.0 μm.荧光光谱分析表明,Eu³⁺取代了NaLa(MoO₄)₂中La³⁺的格位, Eu³⁺在613 nm处红光发射(⁵D₀–⁷F₂跃迁)的浓度猝灭机理是电偶极-电四极相互作用,并发生了Eu³⁺( ⁵D₁ ) + Eu³⁺(⁷F₀ )→ Eu³⁺( ⁵D₀ ) + Eu³⁺(⁷F₃) 交叉弛豫,由此导致浓度猝灭. 关键词： 钼酸盐 水热法 稀土离子 发光     

掺杂离子对白色长余辉发光材料Y2O2S:Tb3+, Eu3+,M2+ (M=Mg,Ca, Sr,Ba),Zr4+性能的影响

采用高温固相法制备了白色长余辉发光材料Y₂O₂S:Tb³⁺, Eu³⁺,M²⁺(M=Mg, Ca, Sr, Ba), Zr⁴⁺, 利用X晶体衍射、发光光谱、余辉曲线和热释光曲线等对制备的材料进行表征。结果表明:掺杂离子没有改变样品晶体结构和发射峰的位置,但对其发光强度、余辉时间及陷阱深度有较大的影响。在263 nm紫外光的激发下,469 nm和626 nm的发射分别对应于Eu³⁺的⁵D₂→⁷F₀、⁵D₀→⁷F₂跃迁,544 nm的发射对应于Tb³⁺的⁵D₄→⁷F₅跃迁,主要通过它们的混合产生白光。掺杂不同二价离子样品的余辉性能按Mg²⁺、Sr²⁺、Ca²⁺、Ba²⁺的顺序递减,其中掺杂Mg²⁺的样品,色度坐标为(0.29,0.32),陷阱深度为1.17 eV,余辉时间长达320 s(≥1 mcd/m²),表现出最佳的发光性能。     

双掺Eu3+ 和Tb3+ 的下转换β-NaYF4的合成与发光性能

采用高温溶剂热法合成了下转换发光材料NaYF₄∶Eu³⁺ 和NaYF₄∶Eu³⁺,Tb³⁺ ,采用X射线衍射(XRD)、场发射扫描电镜(FESEM)、激发(PLE)谱和光致发光(PL)谱对材料的物相结构、形貌特征和发光性质进行了表征和研究,并分析了其发光原理。结果表明:所合成的NaYF₄∶Eu³⁺ 和NaYF₄∶Eu³⁺,Tb³⁺ 为纯六方相晶体,尺寸在100 nm左右;改变Eu³⁺ 和Tb³⁺ 的掺杂浓度后晶格结构没有发生明显变化,说明Eu³⁺ 和Tb³⁺ 取代的是Y³⁺的晶格位置;在394 nm光的激发下,检测到Eu³⁺ 在⁵D₀→⁷F₁ 和⁵D₀→⁷F₂跃迁处的特征发射光,并且可见光强度随着Eu³⁺ 离子掺杂浓度的变化而变化。另外Tb³⁺ 离子浓度对NaYF₄∶Eu³⁺ 晶体结构产生了一定的影响,说明掺杂Tb³⁺ 离子改变了Eu³⁺ 离子所处的配位环境,导致红色发光带增强,而这主要源于电偶极子跃迁的贡献。     

Eu3+和Tb3+掺杂硅酸钇纳米粉体的合成与表征

采用溶胶-凝胶法合成了Y₂SiO₅∶Eu和Y₂SiO₅∶Tb纳米粉体,使用X射线衍射仪、扫描电镜等对粉体的结构、形貌和发光性能进行了分析,研究了Eu³⁺和Tb³⁺不同浓度掺杂硅酸钇纳米粉体的发光性能。在紫外光激发下,所获得的Y₂SiO₅∶Eu纳米粉体的主发射峰均位于612 nm,对应于Eu³⁺的⁵D₀→⁷F₂跃迁;Y₂SiO₅∶Tb纳米粉体的主发射峰均位于540 nm,对应于Tb³⁺的⁵D₄→⁷F₅跃迁。     

退火温度对ZrO2纳米材料中Eu3+离子发光的影响

研究了退火温度对ZrO₂纳米材料中Eu³⁺离子发光性质的影响. 材料的结构、晶粒尺寸和形状以及晶格的排列分别由XRD，TEM表征. 结果表明：用共沉淀法制备的ZrO₂纳米材料具有不随退火温度变化、稳定的四方结构；材料的晶粒尺寸随退火温度的提高而增大；晶格的排列由无序逐渐变为有序；发射光谱表明其主要发射在595 nm和604 nm处；在394 nm的紫外光辐照下得到了不同样品的604 nm荧光发射强度的变化不同. 这种现象与样品中O^2-离子含量和样品表面的表面缺陷有关；另外，电荷迁移带随退火温度的变化而变化.     

Effect of annealing temperature on luminescence of Eu ions doped nanocrystal zirconia

Effect of annealing temperature on luminescence of Eu³⁺ ions was studied in nanocrystal zirconia prepared by co-precipitation. The XRDs reveal with annealing temperature increasing the tetragonal crystal phase of the samples is stable. The emission spectra show the strong emission at 595 and 604 nm at 394 nm excitation. Under continuous UV (394 nm) irradiation the 604 nm emission intensity changes of the samples show as a function of irradiation time. In addition, the charge-transfer states of the samples are affected by the annealing temperature. These are associated with the defects at/in the surface of the nanocrystalline ZrO₂ with Eu³⁺ ions.     

Effect of concentration on the luminescence of Eu ions in nanocrystalline La2O3

Nanocrystalline powders with various Eu³⁺ concentration (from 1 to 10 mol %) doped La₂O₃ were prepared via a combustion route. Their structure and morphology were characterized using X-ray diffraction (XRD) and High-resolution transmission electron microscopy. The emission spectra of the as-synthesized samples show that the strongest emission position is centered at 626 nm corresponding to ⁵D₀→⁷F₂ transition of Eu³⁺ ions and the intensity change of 626 nm emission is considered as a function of ultraviolet (240 nm) irradiation time. The excitation spectra at 626 nm monitoring indicate that the charge transfer state band is varies with different Eu³⁺ ion concentration. These results are attributed to the surface defects of the nanocrystals.     

Hydrothermal preparation and photoluminescent properties of MgAl2O4: Eu spinel nanocrystals

Nanoplates of the MgAl₂O₄ spinel doped with Eu³⁺ ions were prepared by a microwave assisted hydrothermal method. Structural properties of the precursor calcined at 700 and 1000 ^oC powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to the obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The average spinel particle size was determined to be 11 nm after calcination at 700 °C and it increased up to 14 nm after calcination at 1000 °C. The photoluminescent properties of prepared powders with different Eu³⁺ ion concentrations (0-5% mol) were investigated using excitation and emission spectroscopy at room and low temperatures (77 K).     

Blue light emission from Eu ions in sol-gel-derived Al2O3-SiO2 glasses

Blue light-emitting glasses were successfully prepared by doping Eu²⁺ ions in the system Al₂O₃-SiO₂. The Al₂O₃-SiO₂ glasses doped with Eu³⁺ ions were synthesized using a sol-gel method, followed by heating in hydrogen gas atmosphere to reduce into the Eu²⁺ ions. The obtained glasses exhibited emission spectra with peak at ∼450 nm due to 4f⁶5d→4f⁷ (⁸S_7/2) transition, the intensities of which strongly changed depending on their glass composition and heating conditions. The emission quantum efficiency of 48% was achieved by heating the glass with the ratio of Al³⁺ to Eu³⁺ at about 6 at 1000 °C in hydrogen gas atmosphere. It was found that the Al₂O₃-SiO₂ glasses were appropriate not only for homogeneously doping the Eu³⁺ ions in glass structure but also reducing to Eu²⁺ ions, resulting in enhanced blue light-emission properties.     

Synthesis, characterization and optical spectroscopy of Eu doped titanate nanotubes

The synthesis of Eu³⁺ doped titania nanotubes was carried out via a hydrothermal method. X-ray diffraction and transmission electron microscope analyses showed that the nanotubes were formed by rolling multilayered titania structure with a length of up to 100 nm. The Eu³⁺-doped nanotubes exhibited strong emission lines associated with the ⁵D₀→⁷F_J (with J from 1 to 4) transition of Eu³⁺ and the differences between the luminescence properties of the precursor powders and the nanotubes were studied at low temperature.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

Eu3+离子在微晶玻璃研究中的探针作用

制备出单掺Eu³⁺离子的氟氧化物玻璃陶瓷系列样品，利用Eu³⁺离子作为荧光探针，通过热处理前后Eu³⁺离子发射光谱中电偶极子跃迁与磁偶极子跃迁强度比值的变化表征在玻璃材料中微晶是否形成，分析了Eu³⁺离子荧光发射谱中电偶极子跃迁与晶体场对称性的关系，进一步表征了稀土离子所处微晶晶格场的变化. 关键词： 微晶玻璃 探针 3+离子')" href="#">Eu³⁺离子     

发光二极管用SrWO4:Eu3+红光荧光粉激发谱强度的调控

采用化学共沉淀法制备了Eu³⁺掺杂摩尔分数不同、煅烧温度不同的SrWO₄:Eu³⁺系列发光粉体, 所制备的粉体均具有Eu³⁺特征的强室温红光荧光发射. 通过调节煅烧温度和掺杂摩尔分数来调控近紫外和蓝光吸收强度, 进而调控用395 nm的近紫外光和465 nm的蓝光激发样品所得红光发光强度. 研究结果表明, 所制备的SrWO₄:Eu³⁺红光荧光粉可以被紫外和蓝光发光二极管有效激 关键词： 稀土掺杂 4:Eu³⁺')" href="#">SrWO₄:Eu³⁺ 光致发光 白光发光二极管     

Synthesis and luminescence properties of nanocrystalline Gd2O3:Eu by combustion process

The nanocrystalline Gd₂O₃:Eu³⁺ powders with cubic phase were prepared by a combustion method in the presence of urea and glycol. The effects of the annealing temperature on the crystallization and luminescence properties were studied. The results of XRD show pure phase can be obtained, the average crystallite size could be calculated as 7, 8, 15, and 23 nm for the precursor and samples annealed at 600, 700 and 800 °C, respectively, which coincided with the results from TEM images. The emission intensity, host absorption and charge transfer band intensity increased with increasing the temperature. The slightly broad emission peak at 610 nm for smaller particles can be observed. The ratio of host absorption to O²⁻-Eu³⁺ charge transfer band of smaller nanoparticles is much stronger compared with that for larger nanoparticles, furthermore, the luminescence lifetimes of nanoparticles increased with increasing particles size. The effects of doping concentration of Eu³⁺ on luminescence lifetimes and intensities were also discussed. The samples exhibited a higher quenching concentration of Eu³⁺, and luminescence lifetimes of nanoparticles are related to annealing temperature of samples and the doping concentration of Eu³⁺ ions.