水热法制备的Li4-3xEux(MoO4)2微晶及其发光性能

采用水热法制备了Li_4-3xEu_{x(MoO4)2系列红色荧光粉.通过X射线衍射(XRD)、扫描电镜(SEM )和荧光分析(FL)对产物的微结构、形貌和发光性能进行表征分析.XRD分析表明,制备的Li4-3xEux(MoO4)2微晶均为白钨矿四方结构.SEM结果显示:随着x的增大,Li4-3xEux(MoO4)2微晶的晶粒尺寸相应减小,在0.2~0.5 μm之间变化.荧光分析结果表明:源于Eu³⁺的⁵D0→⁷F2和⁵D0→⁷F1电荷转移的592 nm和614 nm的特征发射峰显现明显,后者的发射强度远远大于前者.随着x的增大,样品中Eu³⁺的两个特征发射峰的强度先增大后减小,在x=1.0时达到最大.}     

绿色发光粉CaBa2(BO3)2 ∶ Tb3+的 制备和发光特性

采用高温固相法合成了绿色荧光粉CaBa₂(BO₃)₂ ∶ Tb³⁺ 并对其发光特性进行了研究。发射峰值位于496, 549, 588, 622 nm,分别对应Tb³⁺的⁵D₄ →⁷F₆、⁵D₄ →⁷F₅、⁵D₄ →⁷F₄、⁵D₄ →⁷F₃ 能级跃迁。其中以496 nm和549 nm的发射峰最强,样品呈现很好的绿色发光。 主要激发峰位于200~300 nm之间,属于4f⁷5d¹宽带吸收。考察了Tb³⁺掺杂 浓度和Li⁺ , Na⁺ 和 K⁺ 作为电荷补偿剂对样品发光性能的影响,几乎不发生浓度猝灭现象,Li⁺的补偿效果最好。还确定了原料CaCO₃、BaCO₃、H₃BO₃的最佳配比,当H₃BO₃过量3%时,合成的晶体发光亮度最好。     

LnP5O14晶体中Tb3+和Eu3+的发光光谱特性

本工作测量了室温下TbP₃O₁₄和EuP₅O₁₄晶体的吸收和发射光谱。根据吸收光谱和Judd-Ofelt理论计算了Tb³⁺和Eu³⁺的实验和理论的振子强度。用最小二乘法拟合实验与理论的振子强度得到唯象强度参量Ω_λ。然后计算了Tb³⁺的⁵D₃→⁷F₅,⁵D₄→⁷F₄和⁵D₄→⁷F₆以及Eu³⁺的⁵D₀→⁷F₂,⁵D₀→⁷F₄的跃迁几率和寿命。同时用时间分辨光谱测量了不同温度下相应的荧光辐射寿命。计算与实验结果基本相符。理论和实验的结果表明Tb³⁺的⁵D₃态的寿命主要取决于⁵D₃→⁵D₄和⁷F₆→⁷F₀两能级对之间的电偶极-电偶极交叉弛豫。 关键词：     

双掺Eu3+ 和Tb3+ 的下转换β-NaYF4的合成与发光性能

采用高温溶剂热法合成了下转换发光材料NaYF₄∶Eu³⁺ 和NaYF₄∶Eu³⁺,Tb³⁺ ,采用X射线衍射(XRD)、场发射扫描电镜(FESEM)、激发(PLE)谱和光致发光(PL)谱对材料的物相结构、形貌特征和发光性质进行了表征和研究,并分析了其发光原理。结果表明:所合成的NaYF₄∶Eu³⁺ 和NaYF₄∶Eu³⁺,Tb³⁺ 为纯六方相晶体,尺寸在100 nm左右;改变Eu³⁺ 和Tb³⁺ 的掺杂浓度后晶格结构没有发生明显变化,说明Eu³⁺ 和Tb³⁺ 取代的是Y³⁺的晶格位置;在394 nm光的激发下,检测到Eu³⁺ 在⁵D₀→⁷F₁ 和⁵D₀→⁷F₂跃迁处的特征发射光,并且可见光强度随着Eu³⁺ 离子掺杂浓度的变化而变化。另外Tb³⁺ 离子浓度对NaYF₄∶Eu³⁺ 晶体结构产生了一定的影响,说明掺杂Tb³⁺ 离子改变了Eu³⁺ 离子所处的配位环境,导致红色发光带增强,而这主要源于电偶极子跃迁的贡献。     

Y2O3:Eu纳米晶中能量传递相互作用的研究

通过浓度猝灭曲线确定了引起Y₂O₃纳米晶中Eu³⁺发光浓度猝灭的是交换相互作用.测量了两种颗粒尺寸下Eu³⁺的⁵D₀—⁷F₂跃迁发光衰减曲线随掺杂浓度的变化,利用交换相互作用的理论衰减曲线对实验衰减曲线进行拟合.计算Eu³⁺离子的交换相互作用能量传递的效率,分析了Y₂O_{3关键词： 能量传递 2}O₃Eu纳米晶')" href="#">Y₂O₃Eu纳米晶 发光衰减     

BaWO4∶Eu3+红色荧光粉的水热制备及其发光性能

采用水热法,通过变化水热反应时间制备出不同的BaWO₄∶Eu³⁺样品,利用XRD和SEM分析了样品的晶体结构和表面形貌,研究了基质晶体生长取向对BaWO₄中Eu³⁺离子特征发射的影响。实验结果表明:BaWO₄∶Eu³⁺样品在395 nm近紫外光或464 nm蓝光激发下发射578,592,612 nm的红光,其中612 nm(⁵D₀→⁷F₂)发射强度明显高于592 nm (⁵D₀→⁷F₁)。在水热温度160 ℃的情况下,所制备的样品均为四方相,不同的水热反应时间将影响晶体在各晶向的生长速度,进而影响晶体的对称性和发光性能。水热时间为10 h时的发射强度最大。     

Gd1-xEuxAl3(BO3)4纳米晶的合成及其发光性能

以高温固相反应法合成了Gd_1-xEu_xAl₃(BO₃)₄:Eu³⁺纳米荧光粉。使用XRD分析确定了样品的物相,并根据谢乐公式计算出其微晶的纳米粒度。采用了“粉末悬浮法”以甘油为分散介质,在RF540荧光光度计上测试了纳米晶荧光粉的激发光谱和发射光谱。GdAl₃(BO₃)₄基质本身发光,GdAl₃(BO₃)₄:Eu纳米荧光粉表现了Eu³⁺的特征发射光谱,其中最强峰为⁵D₀→⁷F₂发射,表明晶体结构中没有对称中心格位。实验表明在GdAl₃(BO₃)₄:Eu纳米晶荧光粉中,存在Gd³⁺对Eu³⁺发光的基质敏化作用。     

Tb3+,Eu3+单掺杂、双掺杂SrSiO3的合成、结构表征与发光性能

采用液相沉淀法合成了铽单掺杂,铕单掺杂,铽、铕双掺杂的硅酸锶发光材料。其结构经X-射线衍射表征。研究了合成样品的激发、发光光谱。研究结果表明:在254nm波长紫外光激发下,SrSiO₃:0.04Eu³⁺的发光光谱中出现4个Eu³⁺的发光峰,分别为Eu³⁺的⁵D₀→⁷F₁（588、590nm）、⁵D₀→F₂（609nm）、⁵D₀→⁷F₃（626nm）、⁵D₀→⁴F₄（651nm）跃迁峰;SrSiO₃:0.04Tb³⁺的发光光谱中出现4个Tb³⁺的发光峰,分别为Tb³⁺的⁵D4→^F₆（488nm）、⁵D₄→⁷F₅（541、548nm）、⁵D₄→⁷F₄（584nm）跃迁峰;SrSiO₃:0.04Tb³⁺,0.04Eu³⁺发光体系中,Tb³⁺的共掺杂显著增强了Eu³⁺的特征发射,存在Tb³⁺→Eu³⁺的能量传递现象,结果表明有Eu³⁺和Tb³⁺两个发光中心。     

一种LED用红色荧光粉BaZn2(BO3)2：Eu3+的合成与发光性能研究

通过高温固相法制得双峰可调节本征半导体发光BaZn₂（BO₃）₂：Eu³⁺荧光粉,此类荧光粉在300~400 nm的紫外波段有很强的吸收。在375 nm的紫外光激发下,该荧光粉产生了两个宽带的发射峰,分别位于550 nm和615 nm处。并且,在395 nm的紫光激发下,荧光粉会由于Eu³⁺离子的⁵D₀→⁷F₂电偶极跃迁产生一个位于615 nm的强宽发射峰,这表明Eu³⁺离子占据了反演对称中心的位置,取代了BaZn₂（BO₃）₂中部分的Ba²⁺离子。当Eu³⁺的摩尔分数达到10%时,发生浓度猝灭。在不同浓度的Eu³⁺离子的掺杂下,BaZn₂（BO₃）₂：Eu³⁺荧光粉的发光从黄色延伸到红色,实现了荧光粉的色度可调。     

ZnAl2O4：Tb3+荧光粉的合成、结构及其光学性能研究

通过溶胶-凝胶法制备出不同Tb³⁺掺杂浓度和不同二次煅烧温度下的ZnAl₂O₄:Tb³⁺荧光粉, 并利用X射线衍射(XRD)和荧光光谱等对样品进行了表征。由XRD结果可知,当Tb³⁺掺杂的摩尔分数不大于9%,二次煅烧温度在600℃以上时,所得粉体为结晶性良好的尖晶石相。在紫外光激发下,ZnAl₂O₄:Tb³⁺荧光粉的发射光谱由位于488 nm(⁵D₄→⁷F₆)、542 nm(⁵D₄→⁷F₅)、587 nm(⁵D₄→⁷F₄ )和621.5 nm(⁵D₄→⁷F₃)的4个发射峰组成。研究发现,Tb³⁺的掺杂浓度和二次煅烧温度对样品发光强度有着重要影响,当Tb³⁺的摩尔分数为5%,二次煅烧温度为900℃时,ZnAl₂O₄:Tb³⁺荧光粉的发光最强,继续增加Tb³⁺掺杂浓度或提高煅烧温度,分别会出现浓度猝灭和温度猝灭现象。     

Hydrothermal synthesis, controlled microstructure, and photoluminescence of hydrated Zn3(PO4)2: Eu3+ nanorods and nanoparticles

In this article, Zn₃(PO₄)₂: Eu³⁺ nanorods and nanoparticles have been prepared by the hydrothermal method. The optimum pH value has been found at the range of 3–8 for the preparation of orthorhombic Zn₃(PO₄)₂: Eu³⁺, whose morphologies are affected by the pH value. At the same temperature for hydrothermal reaction, the product presents nanorods at pH 4, while it shows nanoparticles at pH 6. Furthermore, the influences of the hydrothermal reaction temperature on the morphology and microstructure have also been investigated, suggesting that the morphology and microstructure cannot be changed with the hydrothermal temperature at the same pH value. Finally, the photoluminescence of Eu³⁺ on Zn₃(PO₄) nanorod/nanoparticle have been studied, both of which present the characteristic emission lines of Eu³⁺ and the ⁵D₀–⁷F₁ transition corresponds the strongest emission. This indicates that Eu³⁺ occupied the inversion center in Zn₃(PO₄) host.     

Luminescent properties of R2(MoO4)3:Eu (R=La, Y, Gd) phosphors prepared by sol-gel process

A series of red phosphors R_0.8Eu_1.2(MoO₄)₃ (R=La, Y, and Gd) have been synthesized by sol-gel method. The crystallization processes of the phosphor precursors were characterized by X-ray diffraction (XRD) and thermogravimetry-differential thermal analysis (TG-DTA), and the properties of these resulting phosphors have also been characterized by photoluminescence (PL) spectra and reflectance spectra. Field emission scanning electron microscopy (FE-SEM) was also used to characterize the shape and the size of the samples. The results of TG-DTA and XRD indicated that all of the R_0.8Eu_1.2(MoO₄)₃ (R=La, Y, and Gd) phosphors crystallized completely at 650 °C. Y_0.8Eu_1.2(MoO₄)₃ and Gd_0.8Eu_1.2(MoO₄)₃ have two structures, monoclinic and orthorhombic, while La_0.8Eu_1.2(MoO₄)₃ only adopts monoclinic structure. The luminescent properties of phosphors R_0.8Eu_1.2(MoO₄)₃ (R=La, Y, and Gd) are dependent on their structures to some extent. The orthorhombic Y_0.8Eu_1.2(MoO₄)₃ and Gd_0.8Eu_1.2(MoO₄)₃ phosphors show very similar luminescent properties, which differ from those of phosphors with monoclinic structure. For all of R_0.8Eu_1.2(MoO₄)₃ (R=La, Y, and Gd) phosphors, intense red emission is obtained by exciting at ∼394 and ∼465 nm which are owing to the sharp ⁷F₀→⁵L₆ and ⁷F₀→⁵D₂ lines of Eu³⁺. Two strongest lines at 394 and 465 nm in excitation spectra of these phosphors match well with the two popular emissions from near-UV and blue GaN-based LEDs, so they could be used as red components for white light-emitting diodes.     

Hypersensitive and forbidden transitions of trivalent europium ion in Tb1.8Eu0.2 (MoO4)3 single crystal

The fluorescent transitions⁵ D _0.1 →⁷ F _J (J=0−4) of the europium ion in the Tb_1.8Eu_0.2 (MoO₄)₃ single crystal were recorded at 300 and 20 K. The forbidden and the hypersensitive transitions were observed in this system. The intensity ratio between⁵ D ₀ →⁷ F ₁ and⁵ D ₀ →⁷ F ₂ which is 1:5 is discussed in the light of covalency between the Eu³⁺ ion and MoO₄ tetrahedra.     

KGd(MoO4)2:Eu as a promising red phosphor for light-emitting diode application

A red phosphor KGd(MoO₄)₂:Eu³⁺ was prepared by solid-state reaction technique at high temperature. Its photoluminescent property was investigated and the optimum concentration of Eu³⁺ doped in the KGd(MoO₄)₂ is 25 mol%. Compared with Y₂O₂S:0.05Eu³⁺, the obtained KGd(MoO₄)₂:Eu³⁺ shows wider excitation band around 400 nm, higher intensity of Eu^{3+ 5}D₀–⁷F₂ emission upon excitation 393 nm, and the CIE chromaticity coordinates (x = 0.655, y = 0.345) are closer to the standard of National Television Standard Committee (NTSC). The optical properties of KGd(MoO₄)₂:Eu³⁺ suggest that it is an efficient red-emitting phosphor for light-emitting diode applications.     

Synthesis and luminescence properties of red-emitting phosphors NaY0.87Eu0.13(WO4)1.2(MoO4)0.8

A series of NaY_1−yEu_y(WO₄)_2−x(MoO₄)_x (x=0−2 and y=0.06−0.15) phosphors have been prepared by a combustion route. X-ray powder diffraction, photoluminescence excitation and emission spectra were used to characterize the resulting samples. The excitation spectra of these phosphors show the strongest absorption at about 396 nm, which matches well with the commercially available n-UV-emitting GaN-based LED chip. Their emission spectra show an intense red emission at 616 nm due to the ⁵D₀→⁷F₂ electric dipole transition of Eu³⁺. As the Mo content increases, the intensity of the ⁵D₀→⁷F₂ emission of Eu³⁺ activated at wavelength of 396 nm increases and reaches a maximum when the relative ratio of Mo/W is 2:3. The intense red-emission of the tungstomolybdate phosphors at near-UV excitation suggests that the material is a potential candidate for white light emitting diode (WLEDs).     

Synthesis process and the luminescence properties of rare earth doped NaLa(WO4)2 nanoparticles

Rare earth doped NaLa(WO₄)₂ nanoparticles have been prepared by a simply hydrothermal synthesis procedure. The X-ray diffraction (XRD) pattern shows that the Eu³⁺-doped NaLa(WO₄)₂ nanoparticles with an average size of 10-30 nm can be obtained via hydrothermal treatment for different time at 180 °C. The luminescence intensity of Eu³⁺-doped NaLa(WO₄)₂ nanoparticles depended on the size of the nanoparticles. The bright upconversion luminescence of the 2 mol% Er³⁺ and 20 mol% Yb³⁺ codoped NaLa(WO₄)₂ nanoparticles under 980 nm excitation could also be observed. The Yb³⁺-Er³⁺ codoped NaLa(WO₄)₂ nanoparticles prepared by the hydrothermal treatment at 180 °C and then heated at 600 °C shows a 20 times stronger upconversion luminescence than those prepared by hydrothermal treatment at 180 °C or by hydrothermal treatment at 180 °C and then heated at 400 °C.     

Synthesis and photoluminescence properties of?novel red-emitting phosphors for light emitting diodes

The novel red-emitting phosphors K₂Ba_1−x (MoO₄)₂: xEu³⁺(0.02≤x≤0.15) phosphors were prepared by solid-state reaction and their crystal structures, photo luminescent characteristics were investigated. The results show that all samples can be efficiently excited by UV (396 nm) and blue (466 nm) light, which are coupled well with the characteristic emission from UVLED and blue LED, respectively. Their emission spectra show intense red emission at 616 nm with line spectra due to the ⁵D₀–⁷F₂ transition of Eu³⁺. The XRD and photoluminescence experimental results indicate that the K₂Ba(MoO₄)₂: Eu³⁺ phosphor crystallization optimum annealing temperature occurs at about 800°C. The optimum doping concentration of Eu³⁺ is 0.10 mol, and the critical transfer distance (Rc) among Eu³⁺ ions is calculated to be about 11.126 ?. The approach to charge compensation was used: Ba²⁺→Eu³⁺+X⁻ (X=F, Cl, Br), and the charge compensation influence on the luminescent intensity of phosphors is investigated.     

Size-dependent microstructure and europium site preference influence fluorescent properties of Eu-doped Ca10(PO4)6(OH)2 nanocrystal

In this study, Eu³⁺-doped nanocrystalline Ca₁₀(PO₄)₆(OH)₂ (Ca_10−xEu_x(PO₄)₆(OH)₂) with different particle sizes have been prepared by the thermal decomposition of precursors. Size-dependent microstructure could be observed in nanocrystalline Ca_10−xEu_x(PO₄)₆(OH)₂. The lattices of Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals were more distorted in comparison with the bulk, and the smaller the particle size, the more distorted the lattices. Room temperature photoluminescence showed europium site preference was also size-dependent, with the majority of Eu³⁺ ions occupying Ca(II) sites in the bulk, but more and more Eu³⁺ ions occupying Ca(I) sites in Ca_10−xEu_x(PO₄)₆(OH)₂ with decreasing particle size. Fluorescent properties of Ca_10−xEu_x(PO₄)₆(OH)₂ were considered to be influenced by both microstructure and site preference of Eu³⁺ ions. An abnormal strong intensity of ⁵D₀-⁷F₀ transition was observed in bulk and larger Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals, but the relative intensities of ⁵D₀-⁷F₀ transition to ⁵D₀-⁷F_1,2,3,4 transition of Eu³⁺ became weaker as the particle sizes decreased. As the particle sizes became smaller, the ratios of the red emission transition (⁵D₀-⁷F₂) to the orange emission transition (⁵D₀-⁷F₁) (R/O values) first increased by comparing the bulk sample with 96 nm sample, and then decreased by comparing 96 nm sample to 57 nm sample. The quenching concentrations of Ca_10−xEu_x(PO₄)₆(OH)₂ samples increased with decreasing particle size. Possible mechanisms responsible for these phenomena were proposed. Since nanosized Ca_10−xEu_x(PO₄)₆(OH)₂ showed higher fluorescent intensities, higher R/O values and higher quenching concentrations, this material is considered to be a promising phosphor.     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Ionic liquid-assisted hydrothermal synthesis of dendrite-like NaY(MoO4)2:Tb phosphor

Micro-sized NaY(MoO₄)₂:Tb³⁺ phosphors with dendritic morphology was synthesized by a ionic liquid-assisted hydrothermal process. X-ray diffraction (XRD) indicated that the as-prepared product is pure tetragonal phase of NaY(MoO₄)₂. Field emission scanning electron microscopy (FE-SEM) images showed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors have dendritic morphology. The photoluminescent (PL) spectra displayed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors show a stronger green emission with main emission wavelength 545 nm corresponding to the ⁵D₄→⁷F₅ transition of Tb³⁺ ion, and the optimal Tb³⁺ doping concentration for obtaining maximum emission intensity was confirmed to be 10 mol%. Based on Van Uitert's and Dexter's models the electric dipole–dipole (D–D) interaction was confirmed to be responsible for the concentration quenching of ⁵D₄ fluorescence of Tb³⁺ in the NaY(MoO₄)₂:Tb³⁺ phosphors. The intrinsic radiative transition lifetime of ⁵D₄ level is found to be 0.703 ms.