p型ZnO薄膜的制备及特性

采用射频磁控溅射在Si片上制备ZnO薄膜，通过离子注入对样品进行N掺杂，在不同温度下进行退火并实现了p型转变.用扫描电子显微镜、X射线衍射和Hall测量对薄膜进行了表征，结果表明薄膜具有良好的表面形貌和高度c轴择优取向，退火后p型ZnO薄膜的最高载流子浓度和最低电阻率分别为1.68×10¹⁶cm^-3和41.5Ω·cm.讨论并分析了退火温度和时间对ZnO薄膜p型转变的影响.     

Ti离子注入和退火对ZnS薄膜结构和光学性质的影响

利用真空蒸发法在石英玻璃衬底上制备了ZnS薄膜,将能量80 keV,剂量1×10¹⁷ cm^-2的Ti离子注入到薄膜中,并将注入后的ZnS薄膜进行退火处理,退火温度500—700 ℃.利用X射线衍射（XRD）研究了薄膜结构的变化,利用光致发光（PL）和光吸收研究了薄膜光学性质的变化.XRD结果显示,衍射峰在500 ℃退火1 h后有一定程度的恢复;光吸收结果显示,离子注入后光吸收增强,随着退火温度的上升,光吸收逐渐降低,吸收边随着退火温度的提高发生蓝移;PL显示,薄 关键词： ZnS薄膜 离子注入 X射线衍射 光致发光     

退火对He注入及随后208Pb27+辐照的Al2O3单晶PL谱的影响

利用高能离子研究了110 keV 的He⁺注入Al₂O₃单晶及随后230 MeV的²⁰⁸Pb²⁷⁺辐照并在不同温度条件下退火样品的光致发光的特性. 从测试结果可以清楚地看到在375 nm，390 nm，413 nm 和450 nm 出现了强烈的发光峰. 经过600 K退火2 h后测试结果显示，390 nm发光峰增强剧烈，而别的发光峰显示不明显. 在900 K退火条件下，390 nm的发光峰开始减弱相反在510 nm出现了较强的发光峰，到1100 K退火完毕后390 nm的发光峰完全消失，而510 nm的发光峰相对增强. 从辐照样品的FTIR谱中看到，波数在460—510 cm^-1间的吸收是振动模式，经过离子辐照后，吸收带展宽，随着辐照量的增大，Al₂O₃振动吸收峰消失，说明Al₂O₃振动模式被完全破坏. 1000—1300 cm^-1之间为Al-O-Al桥氧的伸缩振动模式，辐照后吸收带向高波数方向移动. 退火后的FTIR谱变化不大.     

Al掺杂原子分数及退火温度对ZnO薄膜光学特性的影响

 采用溶胶凝胶法在（0001）Al₂O₃衬底上制备了不同掺杂原子分数的ZnO:Al薄膜，在Ar气氛中进行了600～950 ℃不同温度的退火处理，研究了掺杂原子分数和退火温度对薄膜光致发光、光吸收和透射的影响。结果显示，薄膜的紫外峰强度随掺杂原子分数和退火温度的提高而增强，与缺陷相关的绿光强度却随着掺杂原子分数和退火温度的提高而降低；薄膜光学带隙随掺杂原子分数的提高从3.21 eV增大到3.25 eV；光吸收在可见光区随着退火温度的升高而增大，在紫外区却随着退火温度的升高而减小，透射与吸收的变化规律相反；薄膜吸收边随退火温度的升高出现轻微的红移。     

ZnO/Zn界面对纳米ZnO薄膜光学性质的影响

采用氧等离子体辅助电子束蒸发金属Zn后低温退火的方法制备纳米ZnO薄膜。利用X射线衍射(XRD)谱、拉曼(Raman)谱、X射线光电子能谱(XPS)以及光致发光(PL)谱等手段,分析了退火温度及ZnO/Zn界面对样品的结构和发光性质的影响。Raman结果表明随着退火温度的升高,界面模式(Es)振动减弱并向低波数方向移动。当退火温度为400℃时,界面振动消失,Zn全部转化成具有六方纤锌矿结构的ZnO,得到化学配比的纳米ZnO薄膜。PL谱表明,经400℃退火处理的样品紫外发射最强,发光性质最好。     

热处理温度对ZnO：Al薄膜性能的影响

利用溶胶-凝胶技术在玻璃衬底上制备了ZnO:Al薄膜,表征了薄膜的结构、光透过和光致发光特性,探讨了热处理温度对薄膜晶体结构和光学性质的影响.结果表明,在热分解温度400 ℃和退火温度600 ℃时,ZnO:Al薄膜的C轴择优取向明显,透过率较高.在热处理温度400 ℃情况下,激发波长340 nm的光致发光谱中有三个发光中心,紫外发光强度随退火温度的升高先升高后下降,500 ℃时发光强度最强.其它两个发光峰的强度随退火温度的升高而降低甚至消失.激发波长不同,ZnO:Al薄膜的发光中心和强度均发生变化.     

热处理温度对ZnO∶Al薄膜性能的影响

利用溶胶-凝胶技术在玻璃衬底上制备了ZnO∶Al薄膜,表征了薄膜的结构、光透过和光致发光特性,探讨了热处理温度对薄膜晶体结构和光学性质的影响.结果表明,在热分解温度400 ℃和退火温度600 ℃时,ZnO∶Al薄膜的C轴择优取向明显,透过率较高.在热处理温度400 ℃情况下,激发波长340 nm的光致发光谱中有三个发光中心,紫外发光强度随退火温度的升高先升高后下降,500 ℃时发光强度最强.其它两个发光峰的强度随退火温度的升高而降低甚至消失.激发波长不同,ZnO∶Al薄膜的发光中心和强度均发生变化.     

ZnO：V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO:V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO:V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO:V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

ZnO∶V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO∶V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO∶V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO∶V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

热处理对ZnO:Zn荧光薄膜结晶性能的影响

用热处理方法对电子束蒸发制备的ZnO:Zn荧光薄膜分别进行400,600℃退火处理。采用X射线衍射、X射线光电子能谱、扫描电子显微镜、光致发光光谱等方法,表征了ZnO:Zn荧光薄膜的结构、成分、形貌、发光性能。在ZnO:Zn荧光薄膜的X射线衍射谱和扫描电子显微镜照片中,可以看出经退火处理后结晶状况大大改善,多晶结构趋于规则,晶粒更加均匀且膜层结构更加致密。在ZnO:Zn荧光薄膜的光致发光谱中,检测到490nm处发光峰,认为一价氧空位(V_O)充当发光中心,且薄膜的光致发光强度受热处理温度的影响很大。实验表明随着退火温度的升高,薄膜的结晶程度提高,弥补了薄膜晶体表面的表面缺陷,薄膜的发光性能不断提高。     

Emittance-dominated long bunches in dual harmonic RF system

The storage of long bunches for long time intervals needs flattened stationary buckets with a large bucket height. The longitudinal motion of the initially mismatched beam has been studied for both the single and dual harmonic RF systems. The RF amplitude is determined to be r.m.s wise matched. The bucket height of the single harmonic system is too small even for shorter bunch with only 20% increased energy spread. The Halo formation and even debunching can be seen after a few synchrotron periods for single particles with large amplitude. In the case of small energy spread for a cooled beam, Coulomb interaction cannot be ignored. The external voltage has to be increased to keep the r.m.s bunch length unchanged. The new voltage ratio R(N) simplifies physics for the emittance-dominated bunches with modest particle number N. For the single harmonic system, substantial amount of debunching occurs without increasing the external voltage, but very little if the RF amplitude is doubled. Results from the ORBIT tracking code are presented for the 1 GeV bunch in the HESR synchrotron, part of the GSI FAIR project.     

Photophysical and photochemical properties of inclusion complexes of β-cyclodextrin with aminocoumarins

B. I. Stepanov Institute of Physics, Academy of Sciences of Belarus, 70, F. Skorina Ave., Minsk, 220072, Belarus. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 62, No. 2, pp. 200–205, March–April, 1995.     

土壤中铅、砷、铬、铜和锌含量的连续快速测定

建立了土壤中铅、砷、铬、铜和锌含量的连续快速测定方法。土壤样品经微波消解,用同一份消解液,分别连续测定土壤中的铅、砷、铬、铜和锌含量,铬、铜和锌采用火焰原子吸收光谱法,铅和砷采用氢化物发生-原子荧光光谱法。采用本方法,对环境土壤标准样品ESS-1黑钙土(GSBZ50011)和ESS-3红壤(GSBZ50013)进行多次测定,检测结果与标样的推荐值吻合。经统计计算,回收率为95.2%—103.6%,精密度RSD均小于7%。本法操作简单快速,光谱测定结果已成功地用于无公害水果和蔬菜生产基地的土壤环境质量评价。     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Spectral luminescent properties of monomeric and associated molecular forms of acridine dyes in polymer matrices

M. V. Lomonosov Moscow State University, Leninskie Gory, 119899, Moscow, Russia. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 62, No. 2, pp. 38–46, March–April, 1995.     

Influence of substrate process tolerances on transmission characteristics of frequency-selective surface

Frequency-selective surface （FSS） is a two-dimensional periodic structure consisting of a dielectric substrate and the metal units （or apertures） arranged periodically on it. When manufacturing the substrate, its thickness and dielectric constant suffer process tolerances. This may induce the center frequency of the FSS to shift, and consequently influence its characteristics. In this paper, a bandpass FSS structure is designed. The units are the Jerusalem crosses arranged squarely. The mode-matching technique is used for simulation. The influence of the tolerances of the substrate＇s thickness and dielectric constant on the center frequency is analyzed. Results show that the tolerances of thickness and dielectric constant have different influences on the center frequency of the FSS. It is necessary to ensure the process tolerance of the dielectric constant in the design and manufacturing of the substrate in order to stabilize the center frequency.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Optical properties of heated air, carbon dioxide, and argon

Stable-plasma generators, spectroscopic measuring equipment, and methods for determining the optical properties of an extremely heated medium with a given composition have been developed. The spectral coefficients of absorption and emission of heated air, carbon dioxide, and argon were studied. A comparison with the data of other theoretical and experimental investigations has been performed. Deceased. Institute of Molecular and Atomic Physics of the Academy of Sciences of Belarus, 70, F. Skorina Ave., Minsk, 220072, Belarus. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 6, pp. 818–826, November–December, 1997.