Enhanced interface properties of diamond MOSFETs with Al_2O_3 gate dielectric deposited via ALD at a high temperature

The interface state of hydrogen-terminated(C–H) diamond metal–oxide–semiconductor field-effect transistor(MOSFET) is critical for device performance. In this paper, we investigate the fixed charges and interface trap states in C–H diamond MOSFETs by using different gate dielectric processes. The devices use Al_2O_3 as gate dielectrics that are deposited via atomic layer deposition(ALD) at 80℃ and 300℃, respectively, and their C–V and I–V characteristics are comparatively investigated. Mott–Schottky plots(1/C~2–VG) suggest that positive and negative fixed charges with low density of about 1011 cm~(-2) are located in the 80-℃-and 300-℃ deposition Al_2O_3 films, respectively. The analyses of direct current(DC)/pulsed I–V and frequency-dependent conductance show that the shallow interface traps(0.46 e V–0.52 e V and0.53 e V–0.56 e V above the valence band of diamond for the 80-℃ and 300-℃ deposition conditions, respectively) with distinct density(7.8 × 10~(13) e V~(-1)·cm~(-2)–8.5 × 10~(13) e V-1·cm~(-2) and 2.2 × 1013 e V~(-1)·cm~(-2)–5.1 × 10~(13) e V~(-1)·cm~(-2) for the80-℃-and 300-℃-deposition conditions, respectively) are present at the Al_2O_3/C–H diamond interface. Dynamic pulsed I–V and capacitance dispersion results indicate that the ALD Al_2O_3 technique with 300-℃ deposition temperature has higher stability for C–H diamond MOSFETs.     

Physical analysis of normally-off ALD Al2O3/GaN MOSFET with different substrates using self-terminating thermal oxidation-assisted wet etching technique

Based on the self-terminating thermal oxidation-assisted wet etching technique, two kinds of enhancement mode Al$_{2}$O$_{3}$/GaN MOSFETs (metal-oxide-semiconductor field-effect transistors) separately with sapphire substrate and Si substrate are prepared. It is found that the performance of sapphire substrate device is better than that of silicon substrate. Comparing these two devices, the maximum drain current of sapphire substrate device (401 mA/mm) is 1.76 times that of silicon substrate device (228 mA/mm), and the field-effect mobility ($\mu_{\rm FEmax}$) of sapphire substrate device (176 cm$^{2}$/V$\cdot$s) is 1.83 times that of silicon substrate device (96 cm$^{2}$/V$\cdot$s). The conductive resistance of silicon substrate device is 21.2 $\Omega {\cdot }$mm, while that of sapphire substrate device is only 15.2 $\Omega {\cdot }$mm, which is 61% that of silicon substrate device. The significant difference in performance between sapphire substrate and Si substrate is related to the differences in interface and border trap near Al$_{2}$O$_{3}$/GaN interface. Experimental studies show that (i) interface/border trap density in the sapphire substrate device is one order of magnitude lower than in the Si substrate device, (ii) Both the border traps in Al$_{2}$O$_{3}$ dielectric near Al$_{2}$O$_{3}$/GaN and the interface traps in Al$_{2}$O$_{3}$/GaN interface have a significantly effect on device channel mobility, and (iii) the properties of gallium nitride materials on different substrates are different due to wet etching. The research results in this work provide a reference for further optimizing the performances of silicon substrate devices.     

Synthesis and characterization of Ca2Sn1-xCexO4 with blue luminescence originating from Ce^4＋ charge transfer transition

Ce^4＋-doped Ca2SnO4 with a one-dimensional structure, which emits bright blue light, is prepared by using a solid-state reaction method. The x-ray diffraction results show that the Ce^4＋ ions doped in Ca2SnO4 occupy the Sn^4＋ sites. The excitation and emission spectra of Ca2Sn1-xCexO4 appear to have broad bands with peaks at - 268nm and -442nm, respectively. A long excited-state lifetime （-83μs） for the emission from Ca2Sn1-xCexO4 suggests that the luminescence originates from a ligand-to-metal Ce^4＋ charge transfer （CT）. The luminescent properties of Ca2Snl_xCexO4 have been compared with those of Sr2CeO4, which is the only material reported so far to show Ce^4＋ CT luminescence. More interestingly, it is observed that the emission intensity of Ca2Sn1-xCexO4 with a small doping concentration （x - 0.03） is comparable to that of Sr2CeO4 in which the concentration of active centre is 100%.     

A novel yellow emitting phosphor Dy3+, Bi3+ co-doped YVO4 potentially for white light emitting diodes

Novel Y1 x yVO4:xDy3+,yBi3+(0.01 ≤ x ≤ 0.05,0 ≤ y ≤ 0.20) phosphors for light emitting diode(LED) were successfully synthesised by solid-state reaction.The calculation results of electronic structure show that YVO4 has a direct band gap with 3 eV at G.The top of the valence band is dominated by O 2p state and the bottom of the conduction band is mainly composed of O 2p and V 3d states.An efficient yellow emission under near-ultraviolet(365 nm) excitation is observed.Compared with the pure YVO4:Dy3+ samples,the Dy3+,Bi3+ co-doped samples show a more intensive emission peak(at 574 nm) and a new broad emission band(450-770 nm),due to the 4F9/2 6H13/2 transition of Dy3+ and the emission of the VO3 4 Bi3+ complex respectively.The optimum chromaticity index of Y1 x yVO4:xDy3+,yBi3+(0.01 ≤ x ≤ 0.05,0 ≤ y ≤ 0.20) is(0.447,0.497),which indicates that YVO4:Dy3+,Bi3+ has higher colour saturation than the commercial phosphor YAG:Ce3+.The effects of concentration of Dy3+,Bi3+,electric states and the photoluminescence properties are discussed in details.     

A new analysis of the ν2 fundamental band of H2O^＋＊

This paper reports that the absorption spectra of H2O^＋ have been measured by tunable mid-infrared diode laser spectroscopy in the spectral range of 1100-1380 cm^-1. The H2O＋ ions are generated in an AC glow discharge of the gaseous mixtures of H2O/He and detected with the velocity modulation technique. Forty new lines are assigned to the ν2 fundamental band of H2O^＋ （X^2B1）. The observed lines together with other data published previously are fitted to the standard effective Hamiltonian of an asymmetric top, yielding a set of improved rotational constants, spin-rotation constants and their quartic and sextic centrifugal distortion constants for the ν2=1 vibrational state of H2O＋.     

Observational constraints on the accelerating universe in the framework of a 5D bounce cosmological model

In the framework of a five-dimensional (5D) bounce cosmological model, a useful function f(z) is obtained by giving a concrete expression of deceleration parameter q(z)=q₁+{q₂}/{1+ln (1+ z)}. Then using the obtained Hubble parameter H(z) according to the function f(z), we constrain the accelerating universe from recent cosmic observations: the 192 ESSENCE SNe Ia and the 9 observational H(z) data. The best fitting values of transition redshift z_T and current deceleration parameter q₀ are given as z_T= 0.65_-0.12^0.25 and q₀ = - 0.76_-0.15^+0.15 (1σ). Furthermore, in the 5D bounce model it can be seen that the evolution of equation of state (EOS) for dark energy w_de can cross over -1 at about z=0.23 and the current value w_0de= - 1.15<- 1. On the other hand, by giving a concrete expression of model-independent EOS of dark energy w_de, in the 5D bounce model we obtain the best fitting values z_T= 0.66_0.08^+0.11 and q₀ = - 0.69_0.10^+0.10 (1σ) from the recently observed data: the 192 ESSENCE SNe Ia, the observational H(z) data, the 3-year Wilkinson Microwave Anisotropy Probe (WMAP), the Sloan Digital Sky Survey (SDSS) baryon acoustic peak and the x-ray gas mass fraction in clusters.     

Analysis of the generation mechanism of the S-shaped J—V curves of MoS2/Si-based solar cells

Amorphous-microcrystalline MoS$_{2}$ thin films are fabricated using the sol-gel method to produce MoS$_{2}$/Si-based solar cells. The generation mechanisms of the S-shaped current density-voltage ($J$-$V$) curves of the solar cells are analyzed. To improve the performance of the solar cells and address the problem of the S-shaped $J$-$V$ curve, a MoS$_{2}$ film and a p$^+$ layer are introduced into the front and back interfaces of the solar cell, respectively, which leads to the formation of a p-n junction between the p-Si and the MoS$_{2}$ film as well as ohmic contacts between the MoS$_{2}$ film and the ITO, improving the S-shaped $J$-$V$ curve. As a result of the high doping characteristics and the high work function of the p$^+$ layer, a high-low junction is formed between the p$^+$ and p layers along with ohmic contacts between the p$^+$ layer and the Ag electrode. Consequently, the S-shaped $J$-$V$ curve is eliminated, and a significantly higher current density is achieved at a high voltage. The device exhibits ideal p-n junction rectification characteristics and achieves a high power-conversion efficiency (CE) of 7.55%. The findings of this study may improve the application of MoS$_{2}$ thin films in silicon-based solar cells, which are expected to be widely used in various silicon-based electronic and optical devices.     

Impacts of dark energy on constraining neutrino mass after Planck 2018

Considering the mass splittings of three active neutrinos, we investigate how the properties of dark energy affect the cosmological constraints on the total neutrino mass $\sum {m}_{\nu }$ using the latest cosmological observations. In this paper, several typical dark energy models, including ΛCDM, wCDM, CPL, and HDE models, are discussed. In the analysis, we also consider the effects from the neutrino mass hierarchies, i.e. the degenerate hierarchy (DH), the normal hierarchy (NH), and the inverted hierarchy (IH). We employ the current cosmological observations to do the analysis, including the Planck 2018 temperature and polarization power spectra, the baryon acoustic oscillations (BAO), the type Ia supernovae (SNe), and the Hubble constant H₀ measurement. In the ΛCDM+$\sum {m}_{\nu }$ model, we obtain the upper limits of the neutrino mass $\sum {m}_{\nu }\lt 0.123\,\mathrm{eV}$ (DH), $\sum {m}_{\nu }\lt 0.156\,\mathrm{eV}$ (NH), and $\sum {m}_{\nu }\lt 0.185\,\mathrm{eV}$ (IH) at the 95% C.L., using the Planck+BAO+SNe data combination. For the wCDM+$\sum {m}_{\nu }$ model and the CPL+$\sum {m}_{\nu }$ model, larger upper limits of $\sum {m}_{\nu }$ are obtained compared to those of the ΛCDM+$\sum {m}_{\nu }$ model. The most stringent constraint on the neutrino mass, $\sum {m}_{\nu }\lt 0.080\,\mathrm{eV}$ (DH), is derived in the HDE+$\sum {m}_{\nu }$ model. In addition, we find that the inclusion of the local measurement of the Hubble constant in the data combination leads to tighter constraints on the total neutrino mass in all these dark energy models.     

Isotopic effect of Cl2+ rovibronic spectra in the A-X system

This paper studies the isotopic effect of Cl2+ rovibronic spectra in the A2Πu(Ω=1/2) X 2Πg(Ω= 1/2) system.Based on the experimental results of the molecular constants of 35 Cl2+,it calculates the vibrational isotope shifts of the(2,7) and(3,7) band between the isotopic species 35 Cl+2,35 Cl 37 Cl+and 37 Cl2+,and estimates the rotational constants of both A 2 Π u and X 2 Π g states for the minor isotopic species 35 Cl 37 Cl+and 37 Cl2+.The experimental results of the spectrum of 35 Cl 37 Cl+(3,7) band proves the above mentioned theoretical calculation.The molecular constants and thus resultant rovibronic spectrum for 37 Cl2+ were predicted,which will be helpful for further experimental investigation.     

The dissociation pathways of N2+ in intense femtosecond laser fields

Using a neutral N2 beam as target,this paper studies the dissociation of N2+ in intense femtosecond laser fields(45 fs,～1×10 16 W/cm 2) at the laser wavelength of 800 nm based on the time-of-flight mass spectra of N + fragment ions.The angular distributions of N+ and the laser power dependence of N + yielded from different dissociation pathways show that the dissociation mechanisms mainly proceed through the couplings between the metastable states(A,B and C) and the upper excited states of N2+.A coupling model of light-dressed potential energy curves of N+2 is used to interpret the kinetic energy release of N+.     

Green and red up-conversion emissions and thermometric application of Er^3＋-doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663 nm of wavelength, corresponding respectively to the ^2H11/2 → ^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 → ^4I15/2 transitions of Er^3＋ ions, have been observed for the Er^3＋-doped silicate glass excited by a 978 nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296-673 K, which shows that Er^3＋-doped silicate glass can be used as a sensor in high-temperature measurement.     

Optical parameters and energy levels splitting of Ho^3＋ in Ho^3＋： GdVO4

Ho^3＋ ： GdVO4 is a new laser material suitable for high-power laser systems. In this paper we measure the absorption spectra of Ho^3＋ in the sample Ho^3＋： GdVO4. The intensity parameters are calculated by using the Judd-Ofelt theory. Some predicted spectroscopic parameters, such as the spontaneous radiative transition rate, branching ratio and integrated emission cross section are dealt with. And we also compare the optical parameters with those of other materials. From these results, it is found that there are many transitions which have large oscillator strengths and large integrated emission cross sections. Especially the transitions such as ^5 F4 → ^5 I 8, ^5 S2→^5 I8, ^5 F5 → ^5 I8 and ^5 I7 →^ 5 I8 are useful in solid-state lasers and other fields. Finally, we discuss the splitting of the energy levels of Ho^3＋ in the crystal GdVO4 based on the group theory.     

The splitting of low-lying states for hydroxyl molecule under spin--orbit coupling

The splitting of potential energy curves for the states $X^{2}\Pi _{3/2}$, $^{2}\Pi _{1/2}$ and $A^{2}\Sigma ^{ +}$ of hydroxyl OH under spin--orbit coupling (SOC) has been calculated by using the SO multi-configuration quasi-degenerate perturbation theory (SO-MCQDPT). Their Murrell--Sorbie (M--S) potential functions have been derived, then, the spectroscopic constants for $X^{2}\Pi _{3/2}$,$^{ 2}\Pi _{1/2}$ and $A^{2}\Sigma ^{ + }$ have been derived from the M--S function. The calculated dissociation energies for the three states are $D_{0}$[OH($X^{2}\Pi _{3/2})$]=34966.632cm$^{-1}$, $D_{0}$[OH($^{2}\Pi _{1/2})$]=34922.802cm$^{-1}$, and $D_{0}$[OH($A^{2}\Sigma ^{ + })$]=17469.794cm$^{-1}$, respectively. The vertical excitation energy $\nu [ {{ }^2\Pi _{1/2} ( {\nu = 0} ) \to {X}{ }^2\Pi _{3/2} ( {\nu = 0} )} ] = 139.6{\rm cm}^{-{\rm 1}}$. All the spectroscopic data for the $X^{2}\Pi _{3/2}$ and $^{2}\Pi _{1/2 }$ are given for the first time except the dissociation energy of $X^{2}\Pi _{3/2}$.     

Green and red up-conversion emissions and thermometric application of Er3+-doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663\,nm of wavelength, corresponding respectively to the ${^{2}}H_{11 / 2} \to {^{4}}I_{15 / 2}$, ${^{4}}S_{3 / 2} \to {^{4}}I_{15 / 2}$ and ${^{4}}F_{9 / 2} \to {^{4}}I_{15 / 2}$ transitions of Er$^{3 + }$ ions, have been observed for the Er$^{3 + }$-doped silicate glass excited by a 978\,nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296--673\,K, which shows that Er$^{3 + }$-doped silicate glass can be used as a sensor in high-temperature measurement.     

The fabrication of nickel silicide ohmic contacts to n-type 6H-silicon carbide

This paper reports that the nickel silicide ohmic contacts to n-type 6H-SiC have been fabricated. Transfer length method test patterns with NiSi/SiC and NiSi硅化镍;欧姆触点;n型碳化硅;制造;能带;带隙Project supported by the National Basic Research Program of China (Grant No~2002CB311904), the National Defense Basic Research Program of China (Grant No~51327010101) and the National Natural Science Foundation of China (Grant No~60376001).2006-09-192006-10-30This paper reports that the nickel silicide ohmic contacts to n-type 6H-SiC have been fabricated. Transfer length method test patterns with NiSi/SiC and NiSi2/SiC structure axe formed on N-wells created by N^＋ ion implantation into Si-faced p-type 6H-SiC epilayer respectively. NiSi and NiSi2 films are prepared by annealing the Ni and Si films separately deposited. A two-step annealing technology is performed for decreasing of oxidation problems occurred during high temperature processes. The specific contact resistance Pc of NiSi contact to n-type 6H-SiC as low as 1.78× 10^-6Ωcm^2 is achieved after a two-step annealing at 350 ℃for 20 min and 950℃ for 3 min in N2. And 3.84×10-6Ωcm^2 for NiSi2 contact is achieved. The result for sheet resistance Rsh of the N＋ implanted layers is about 1210Ω/□. X-ray diffraction analysis shows the formation of nickel silicide phases at the metal/n-SiC interface after thermal annealing. The surfaces of the nickel silicide after thermal annealing are analysed by scanning electron microscope.     

Infrared-to-visible and infrared-to-violet upconversion fluorescence of rare earth doped LaF3 nanocrystals

This paper reports that hexagonal-phase LaF3：Yb0.20^3＋,Er0.02^3＋ and LaF3：Yb0.20^3＋, Tm0.02^3＋ nanocrystals （NCs） were synthesized via a hydrothermal method. The transmission electron microscopy, selected area electron diffraction, powder x-ray diffraction, and thermogravimetric analysis are used to characterize the NCs. Under 980 nm excitation, the Yb^3＋/Er^3＋ and Yb^3＋/Tm^3＋ codoped NCs colloidal solutions present bright green and blue upconversion fluorescence, respectively. These NCs show efficient infrared-to-violet and infrared-to-visible upconversion. The upconversion fluo- rescence mechanisms of LaF2：Yb0.20^3＋, Er0.02^3＋ and LaF3：Yb0.20^3＋,Tm0.02^3＋ NCs are investigated with a 980-nm diode laser as excitation source.     

Theory of nine elastic constants of biaxial nematics

In this paper, a rotational invariant of interaction energy between two biaxial-shaped molecules is assumed and in the mean field approximation, nine elastic constants for simple distortion patterns in biaxial nematics are derived in terms of the thermal average （Dmn^（l）） （Dm＇n＇^（l＇））, where Dmn^（l） is the Wigner rotation matrix. In the lowest order terms, the elastic constants depend on coefficients Γ,Γ＇, λ, order parameters Q0 = Q0（D00^（2）） ＋Q2（D02^（2）＋D0-2^（2）） and Q2 = Q0（D20^（2）） ＋ Q2（D22^（2）＋D2-2^（2））. Here Γ and Γ＇ depend on the function form of molecular interaction energy vj′j″j （τ12） and probability function fk′k″k （τ12）, where r12 is the distance between two molecules, and λ is proportional to temperature. Q0 and Q2 are parameters related to multiple moments of molecules. Comparing these results with those obtained from Landau-de Gennes theory, we have obtained relationships between coefficients, order parameters used in both theories. In the special case of uniaxial nematics, both results are reduced to a degenerate case where K11=K33.     

Spin polarization effect for molecule Ta2

Density functional theory （DFT） （B3p86） has been used to optimize the structure of the molecule Ta2. The result shows that the ground state of molecule Ta2 is a 7-multiple state and its electronic configuration is ^7∑u^＋, which shows the spin polarization effect for molecule Ta2 of transition metal elements for the first time. Meanwhile, spin pollution has not been found because the wavefunction of the ground state does not mix with those of higher states. So, the fact that the ground state of molecule Ta2 is a 7-multiple state indicates a spin polarization effect of molecule Ta2 of the transition metal elements, i.e. there exist 6 parallel spin electrons and the non-conjugated electrons are greatest in number. These electrons occupy different space orbitals so that the energy of molecule Ta2 is minimized. It can be concluded that the effect of parallel spin of the molecule Ta2 is larger than the effect of the conjugated molecule, which is obviously related to the effect of d-electron delocalization. In addition, the Murrell-Sorbie potential functions with parameters for the ground state ^7∑u^＋ and other states of the molecule Ta2 are derived. The dissociation energy De, equilibrium bond length Re and vibration frequency we for the ground state of molecule Ta2 are 4.5513eV, 0.2433nm and 173.06cm^-1, respectively. Its force constants f2, f3 and f4 are 1.5965×10^2aJ.nm^-2, -6.4722×10^3aJ·nm^-3 and 29.4851×10^4aJ·nm^-4, respectively. Other spectroscopic data we xe, Be and αe for the ground state of Ta2 are 0.2078cm^-1, 0.0315 cm^-1 and 0.7858×10^-4 cm^-1, respectively.     

Numerical study of IP3-induced Ca2+ spiral pattern evolution

The effect of change in concentration of messenger molecule inositol 1,4,5-trisphosphate (IPspiral wave, Ca$^{2 + }$, IPspiral wave, Ca$^{2 + }$, IP$_{3}$Project supported by the National Natural Science Foundation of China (Grant Nos 10575041 and 10747005)0545The effect of change in concentration of messenger molecule inositol 1,4,5-trisphosphate (IP$_{3})$ on intracellular Ca$^{2 + }$spiral pattern evolution is studied numerically. The results indicate that when the IP$_{3}$ concentration decreases from 0.27\,$\mu $M, a physiologically reasonable value, to different values, the spiral centre drifts to the edge of the medium and disappears for a small enough IP$_{3}$ concentration. The instability of spiral pattern can be understood in terms of excitability-change controlled by the IP$_{3}$ concentration. On the other hand, when the IP$_{3}$ concentration increases from 0.27\,$\mu $M, a homogeneous area with a high Ca$^{2 + }$ concentration emerges and competes with the spiral pattern. A high enough IP$_{3}$ concentration can lead the homogeneous area to occupy the whole medium. The instability of spiral pattern is ascribed to the change in stability of a stationary state with a high Ca$^{2 + }$ concentration.     

High density Al2O3/TaN-based metal--insulator-- metal capacitors in application to radio frequency integrated circuits

Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically. The capacitors exhibit a high density of about 6.05 fF/μm^2, a small leakage current of 4.8 × 10^-8 A/cm^2 at 3 V, a high breakdown electric field of 8.61 MV/cm as well as acceptable voltage coefficients of capacitance （VCCs） of 795 ppm/V2 and 268ppm/V at 1 MHz. The observed properties should be attributed to high-quality Al2O3 film and chemically stable TaN electrodes. Further, a logarithmically linear relationship between quadratic VCC and frequency is observed due to the change of relaxation time with carrier mobility in the dielectric. The conduction mechanism in the high field ranges is dominated by the Poole-Frenkel emission, and the leakage current in the low field ranges is likely to be associated with trap-assisted tunnelling. Meanwhile, the Al2O3 dielectric presents charge trapping under low voltage stresses, and defect generation under high voltage stresses, and it has a hard-breakdown performance.