Effect of charge compensation on emission spectrum of Ca2SiO4：Dy^3＋ phosphor

The Ca2SiO4：Dy^3＋ phosphor was synthesized by the high temperature solid-state reaction method in air. The emission spectrum of Ca2SiO4：Dy^3＋ phosphor shows several bands at 486, 575, and 665 nm under the 365-nm excitation. The effects of Li^＋, Na^＋, and K^＋ on the emission spectrum of Ca2SiO4：Dy^3＋ phosphor were studied. The results show that the emission spectrum intensity is greatly influenced by Li^＋, Na^＋, and K^＋. The charge compensation concentration corresponding to the maximum emission intensity is different with different charge compensations.     

Sr3Bi（PO4）3：Eu^2＋ Luminescence,Concentration Quenching and Crystallographic Sites

A blue emitting phosphor Sr3Bi（PO4）3：Eu2＋ is synthesized luminescent property is investigated. Sr3Bi（PO4 ）3 ：Eu^2＋ can by a high-temperature solid state method, and its create blue emission under the 332 radiation excitation, and the prominent luminescence in blue （423nm） due to the 4fSd^1→4f^7 transition of the Eu^2＋ ion. The crystallographic sites of the Eu^2＋ ion in Sr3Bi（PO4）3 are analyzed, and the 420 and 440 nm emission peaks of the Eu^2＋ ion are assigned to the nine-coordination and eight-coordination, respectively. The emission intensity of Sr3Bi（PO4）3：Eu^2＋ is influenced by the Eu^2＋ doping content, and the concentration quenching effect is observed. The quenching mechanism is the dipole-dipole interaction, and the critical distance of energy transfer is calculated by the concentration quenching method to be approximately 1.72nm.     

Optimum fluorescence emission around 1.8 μm for LiYF4 single crystals of various Tm3＋-doping concentrations

In this paper, optical spectra of LiYF4 single crystals doped with Tm3＋ ions of various concentrations are reported. The emission intensity at 1.8 ktm first increases with increasing Tm3＋ concentration, and reaches a maximum value when the concentration of Tm3＋ is about 1.28 mol%, then it decreases rapidly as the concentration of Tm3＋ further increases to 3.49 mol%. The emission lifetime at 1.8 p.m also shows a similar tendency to the emission intensity. The maximum lifetime of 1.8 μm is measured to be 17.68 ms for the sample doped with Tm3＋ of 1.28 mol%. The emission cross section of 3F4 level is calculated. The maximum reaches 3.76 × 10 -21 cm2 at 1909 nm. The cross relaxation （3H6, 3H4 →3 F4, 3F4） between Tm3＋ ions and the concentration quenching effect are mainly attributed to the change of emission with Tm3＋ concentration. The largest quantum efficiency between Tm3＋ ions is estimated to be ,-147% from the measured lifetime and calculated radiative lifetime. All the results suggest that the Tm3＋/LiYF4 single crystal may have potential applications in 2 μm mid-infrared lasers.     

The concentration quenching and crystallographic sites of Eu2+ in Ca2BO3Cl

A yellow phosphor, Ca2BO3CI：Eu2＋, is prepared by the high-temperature solid-state method. Under the condition of excitation sources ranging from ultraviolet to visible light, efficient yellow emission can be observed. The emission spectrum shows an asymmetrical single intensive band centred at 573 nm, which corresponds to the 4f65dl→4f7 transition of Eu2＋. Eu2＋ ions occupy two types of Ca2＋ sites in the Ca2BO3C1 lattice and form two corresponding emission centres, respectively, which lead to the asymmetrical emission of Eu2＋ in Ca2BO3C1. The emission intensity of Eu2＋ in Ca2BO3C1 is influenced by the Eu2＋ doping concentration. Concentration quenching is discovered, and its mechanism is verified to be a dipole-dipole interaction. The value of the critical transfer distance is calculated to be 2.166 nm, which is in good agreement with the 2.120 nm value derived from the experimental data.     

Structural and Luminescence Properties of Transparent Nanocrystalline ZrO2：Er^3＋ Films

The structural and luminescence properties of nanocrystalline ZrO2 ：Er^3＋ films are reported. Transparent nano-ZrO2 crystalline films doped with Er^3＋ have been prepared using a wet chemistry process. An intense roomtemperature emission at 1527nm with a full width at half-maximum of 46 nm has been observed, which is assigned to the ^4Ⅰ13/2 → ^4Ⅰ15/2 intra-4f^n electric transition of Er^3＋. Correlations between the luminescence properties and structures of the nanocrystalline ZrO2 ：Er^3＋ films have been investigated. Infrared-to-visible upconversion occurs simultaneously upon excitation of a commercially available 980-nm laser diode and the involved mechanisms have also been explained. The results indicate that the nanocrystalline ZrO2：Er^3＋ films might be suggested as promising materials for achieving broadband Er^3＋-doped waveguide amplifiers and upconversion waveguide lasers.     

Preparation and Luminescence Characteristics of Ca3Y2（BO3）4：Eu^3＋ Phosphor

Ca3Y2 （BO3）4：Eu^3＋ phosphor is synthesized by high temperature solid-state reaction method, and the Iuminescence characteristics are investigated. The emission spectrum exhibits two strong red emissions at 613 and 621 nm corresponding to the electric dipole ^5 Do- ^7F2 transition of Eu^3＋ under 365 nm excitation, the reason is that Eu^3＋ substituting for Y^3＋ occupies the non-centrosymmetric position in the crystal structure of Ca3 Y2 （BO3）4. The excitation spectrum for 613 nm indicates that the phosphor can be effectively excited by ultraviolet （UV） （254 nm, 365nm and 400nm） and blue （470nm） light. The effect of Eu^3＋ concentration on the emission intensity of Ca3 Y2 （BO3）4 ：Eu^3＋ phosphor is measured, the result shows that the emission intensities increase with increasing Eu^3＋ concentration, then decrease. The CIE colour coordinates of Ca3Y2 （BO3）4：Eu^3＋ phosphor is （0.639, 0.357） at 15mol% Eu^3＋.     

Luminescence Properties of Sr2SnO4：Sm^3＋ Afterglow Phosphor

A new long-lasting phosphorescence （LLP） phosphor, Sr2SnO4：Sm3＋ which emits reddish-orange LLP upon UV-excitation, is prepared by a conventional high-temperature solid-state method. After irradiation under 247-nm UV light, Sr2SnO4：Sm3＋ emits an intense reddish-orange emission afterglow from the 4G5/2 to 6HJ （J = 5/2,7/2,9/2） transitions. The afterglow decay curve of the Sm3＋-doped Sr2SnO4 phosphor contains a fast decay component and another slow decay one. Due to the presence of the slow decay component, the afterglow can be seen with the naked eye in the dark clearly for more than 1 h after removal of the excitation source.     

A novel strong green phosphor： K3Gd（PO4）2：Ce^3＋, Tb^3＋ for a UV-excited white light-emitting-diode

A series of K3Gd1-x-y（PO4）2：xCe^3＋, yTb^3＋ phosphors are synthesized by the solid-sate reaction method. X-ray diffraction and photoluminescence spectra are utilized to characterize the structures and luminescence properties of the as-synthesized phosphors. Co-doping of Ce^3＋ enhances the emission intensity of Tb^3＋ greatly through an efficient energy transfer process from Ce^3＋ to Tb^3＋. The energy transfer is confirmed by photoluminescence spectra and decay time curves analysis. The efficiency and mechanism of energy transfer are investigated carefully. Moreover, due to the non- concentration quenching property of K3Tb（PO4）2, the photoluminescence spectra of K3Tb1-x（PO4）2：xCe^3＋ are studied and the results show that when x = 0.11 the strongest Tb^3＋ green emission can be realized.     

Preparation and luminescence characteristics of Eu^2＋ activated silicate phosphor

This paper synthesizes the Sr2SiO4：Eu^2＋ phosphor by high temperature solid-state reaction. The emission spectrum of Sr2SiO4 ： Eu^2＋ shows two bands centred at 480 and 547 nm, which agree well with the calculation values of emission spectrum, and the location of yellow emission of Sr2SiO4 ： Eu^2＋ is influenced by the Eu^2＋ concentration. The excitation spectrum for 547 nm emission has two bands at 363 and 402 nm. The emission spectrum of white light emitting diodes （w-LEDs） based on Sr2SiO4 ： Eu^2＋ phosphor ＋ InGaN LED was investigated.     

Photoluminescence characteristics and energy transfer between Bi~（3＋） and Eu~（3＋） in Na_2O–CaO–GeO_2–SiO_2 glass

We report the photoluminescence（PL） of Eu^3＋-doped glass with Bi^3＋as a sensitizer. The specific glass system with the strong enhancement of the red emission of Eu3＋is obtained by adding a small number of Bi3＋ions instead of increasing the Eu^3＋ concentration. The emission band of Bi3＋overlaps with the excitation band of Eu^3＋ and the lifetime decay curves,resulting in a very efficient energy transfer from Bi^3＋ to Eu^3＋. The probability of energy transfer is strongly dependent on Bi^3＋ concentration. In addition, the intensity of 4f–4f transition is much stronger than that of a charge-transfer（CT） band in the excitation spectrum, which indicates that the Na2O–Ca O–Ge O2-Si O2 glass is a suitable red-emitting phosphor with high stability as a candidate for light-emitting diodes（LEDs）.     

Judd--Ofelt analysis of spectra and experimental evaluation of laser performance of Tm3+ doped Lu2SiO5 crystal

This paper reports that the Tm^3＋：Lu2SiO5 （Tm：LSO） crystal is grown by Czochralski technique. The roomtemperature absorption spectra of Tm：LSO crystal are measured on a b-cut sample with 4 at.% thulium. According to the obtained Judd-Ofelt intensity parameters Ω2=9.3155×10^-20 cm^2, Ω4=8.4103×10^-20 cm^2, Ω6=1.5908×10^-20 cm^2, the fluorescence lifetime is calculated to be 2.03 ms for ^3F4 → ^3H6 transition, and the integrated emission cross section is 5.81×10^-18 cm^2. Room-temperature laser action near 2μm under diode pumping is experimentally evaluated in Tm：LSO. An optical-optical conversion efficiency of 9.1% and a slope efficiency of 16.2% are obtained with continuouswave maximum output power of 0.67 W. The emission wavelengths of Tm：LSO laser are centred around 2.06μm with spectral bandwidth of -13.6 nm.     

Optical parameters and energy levels splitting of Ho^3＋ in Ho^3＋： GdVO4

Ho^3＋ ： GdVO4 is a new laser material suitable for high-power laser systems. In this paper we measure the absorption spectra of Ho^3＋ in the sample Ho^3＋： GdVO4. The intensity parameters are calculated by using the Judd-Ofelt theory. Some predicted spectroscopic parameters, such as the spontaneous radiative transition rate, branching ratio and integrated emission cross section are dealt with. And we also compare the optical parameters with those of other materials. From these results, it is found that there are many transitions which have large oscillator strengths and large integrated emission cross sections. Especially the transitions such as ^5 F4 → ^5 I 8, ^5 S2→^5 I8, ^5 F5 → ^5 I8 and ^5 I7 →^ 5 I8 are useful in solid-state lasers and other fields. Finally, we discuss the splitting of the energy levels of Ho^3＋ in the crystal GdVO4 based on the group theory.     

Synthesis and photoluminescence properties of Nd2O3 nanoparticles modified by sodium bis 2-ethylhexyl sulfosuccinate

This paper reports that Nd₂O₃ nanoparticles modified by AOT(sodium bis(2-ethylhexyl) sulfosuccinate) were prepared using microemulsion method in the system of water and propanol/AOT/toluene. Transmission electron microscopy shows that the Nd₂O₃ nanoparticles take the shape of sphere with 18\,nm and 31nm with different preparation. The organic sol of Nd₂O₃ nanoparticles is very stable at room temperature. X-ray diffraction results show that the product has hexagonal phase structure. Two ultraviolet emission band at 344\,nm and 361\,nm corresponding to the transition of ⁴D_3/2→4I_9/2 and 2P_3/2→⁴I₁₁₂ or ⁴D_3/2 →⁴I_13/2 were observed.     

Photoluminescence characterization of Ce and Dy doped Li2CaGeO4 phosphors

Ce³⁺ and Dy³⁺ activated Li₂CaGeO₄ phosphors were prepared by a solid-state reaction method, and characterized by XRD (X-ray diffraction) and photoluminescence techniques. The characteristic emission bands of Dy³⁺ due to ⁴F_9/2→⁶H_15/2 (blue) and ⁴F_9/2→⁶H_13/2 (yellow) transitions were detected in the emission spectra of Li₂CaGeO₄:Dy³⁺. Ce³⁺ broad band emission was observed in Li₂CaGeO₄:Ce³⁺ phosphors at 372 and 400 nm due to 5d→4f transition when excited at 353 nm. Co-doping of Ce³⁺ enhanced the luminescence of Dy³⁺ significantly and concentration quenching occurs when Dy³⁺ is beyond 0.04 mol%. White-light with different hues can be realized by tuning Dy³⁺ concentration in the phosphors.     

Green and red up-conversion emissions and thermometric application of Er3+-doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663\,nm of wavelength, corresponding respectively to the ${^{2}}H_{11 / 2} \to {^{4}}I_{15 / 2}$, ${^{4}}S_{3 / 2} \to {^{4}}I_{15 / 2}$ and ${^{4}}F_{9 / 2} \to {^{4}}I_{15 / 2}$ transitions of Er$^{3 + }$ ions, have been observed for the Er$^{3 + }$-doped silicate glass excited by a 978\,nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296--673\,K, which shows that Er$^{3 + }$-doped silicate glass can be used as a sensor in high-temperature measurement.     

High density Al2O3/TaN-based metal--insulator-- metal capacitors in application to radio frequency integrated circuits

Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically. The capacitors exhibit a high density of about 6.05 fF/μm^2, a small leakage current of 4.8 × 10^-8 A/cm^2 at 3 V, a high breakdown electric field of 8.61 MV/cm as well as acceptable voltage coefficients of capacitance （VCCs） of 795 ppm/V2 and 268ppm/V at 1 MHz. The observed properties should be attributed to high-quality Al2O3 film and chemically stable TaN electrodes. Further, a logarithmically linear relationship between quadratic VCC and frequency is observed due to the change of relaxation time with carrier mobility in the dielectric. The conduction mechanism in the high field ranges is dominated by the Poole-Frenkel emission, and the leakage current in the low field ranges is likely to be associated with trap-assisted tunnelling. Meanwhile, the Al2O3 dielectric presents charge trapping under low voltage stresses, and defect generation under high voltage stresses, and it has a hard-breakdown performance.     

Effect of carbon nanotubes addition on thermoelectric properties of Ca3Co4O9 ceramics

Increasing the phonon scattering center by adding nanoparticles to thermoelectric materials is an effective method of regulating the thermal conductivity. In this study, a series of Ca$_{3}$Co$_{4}$O$_{9}/x$ wt.% CNTs ($x=0$, 3, 5, 7, 10) polycrystalline ceramic thermoelectric materials by adding carbon nanotubes (CNTs) were prepared with sol-gel method and cold-pressing sintering technology. The results of x-ray diffraction and field emission scanning electron microscopy show that the materials have a single-phase structure with high orientation and sheet like microstructure. The effect of adding carbon nanotubes to the thermoelectric properties of Ca$_{3}$Co$_{4}$O$_{9}$ was systematically measured. The test results of thermoelectric properties show that the addition of carbon nanotubes reduces the electrical conductivity and Seebeck coefficient of the material. Nevertheless, the thermal conductivity of the samples with carbon nanotubes addition is lower than that of the samples without carbon nanotubes. At 625 K, the thermal conductivity of Ca$_{3}$Co$_{4}$O$_{9}$/10 wt.% CNTs sample is reduced to 0.408 W$\cdot$m$^{-1}\cdot$K$^{-1}$, which is about 73% lower than that of the original sample. When the three parameters are coupled, the figure of merit of Ca$_{3}$Co$_{4}$O$_{9}$/3 wt.% CNTs sample reaches 0.052, which is 29% higher than that of the original sample. This shows that an appropriate amount of carbon nanotubes addition can reduce the thermal conductivity of Ca$_{3}$Co$_{4}$O$_{9}$ ceramic samples and improve their thermoelectric properties.     

Investigations of the electron paramagnetic resonance parameters and the tetragonal local structure for (VCl6)4- coordination complex in MCl:V2+ (M=Na, K, Rb) systems

By simulating the electron paramagnetic resonance (EPR) and optical spectra on the basis of the 120×120 complete energy matrix, this paper determines the local lattice structure parameters R1 and R2 for MCl:V2+ (M=Na, K, Rb) systems at 77 K, 195 K and RT (room temperature 295 K or 302 K), respectively. The theoretical results indicate that there exists a compressed distortion in MCl:V2+ systems. Meanwhile, it finds that the structure parameters R1, R2 and |△R| (= R1-R2) increase with the rising temperature. Subsequently, from the analysis it concludes that the relation of EPR parameter D vs.△R is approximately linear. Finally, the effects of orbital reduction factor k on the g factors for the three systems have been discussed.     

Magnetic properties and magnetocaloric effects in Tb6Co1.67Si3 compound

Magnetic properties and magnetocaloric effects of Tb₆Co_1.67Si₃ have been investigated by magnetization measurement. This compound is of a hexagonal Ce$_{6}$Ni$_{2}$Si$_{3}$-type structure with a saturation magnetization of 187\,emu/g at 5\,K and a reversible second-order magnetic transition at Curie temperature $T_{\rm C} = 186$\,K. A magnetic entropy change $\Delta S = 7$\,J\,$\cdot$\,kg$^{-1}$\,$\cdot$\,K$^{-1}$ is observed for a magnetic field change from 0 to 5\,T. A large value of refrigerant capacity (RC) is found to be 330\,J/kg for fields ranging from 0 to 5\,T. The large RC, the reversible magnetization around $T_{\rm C}$ and the easy fabrication make the Tb₆Co_1.67Si₃ compound a suitable candidate for magnetic refrigerants in a corresponding temperature range.