石墨烯增强半导体态二氧化钒近场热辐射

本文基于涨落耗散定理和并矢格林函数求解麦克斯韦方程来研究两个半无限大平板的近场热辐射净热流,提出了两个半无限大块状二氧化钒组成的V/V结构、石墨烯覆盖两个半无限大块状二氧化钒组成的GV/GV结构和石墨烯覆盖VO2薄膜组成的GV0/GV0结构,深入研究了这三种结构中二氧化钒与石墨烯间的近场热辐射,并分析了真空间距、二氧化钒薄膜厚度和石墨烯化学势等物理参量变化对近场热辐射的影响.研究表明:三种结构的近场热辐射均随间距增大而减小;在真空间距为10 nm时,由石墨烯覆盖的GV/GV结构的近场辐射热流比无石墨烯覆盖的V/V结构增强35倍,耦合效果最好的是GV0/GV0结构,该结构的近场辐射热流比GV/GV结构增强8.6倍;在GV0/GV0结构中,当二氧化钒薄膜厚度为30 nm时,石墨烯化学势从0.1 eV增加到0.6 eV辐射热流会减小3.3倍.本文系统研究了二氧化钒与石墨烯间相互耦合的近场热辐射,对相关结构的近场热辐射实验和实际应用具有理论指导意义.     

调幅W(Mo)/Cu纳米多层膜He+离子辐照响应行为

用磁控溅射技术制备不同调幅波长 (L) 的W(Mo)/Cu纳米多层膜,所制膜系在60 keV氦离子 (He⁺) 辐照条件下注入不同剂量: 0, 1×10¹⁷ He⁺/cm², 5×10¹⁷ He⁺/cm². 用X射线衍射仪 (XRD) 和高分辨透射电子显微镜(TEM)表征W(Mo)/Cu纳米多层膜辐照前后微观结构. 研究结果表明: 1) He⁺离子轰击引起温升效应是导致沉积态亚稳相β-W 转变成稳态 α-W相的主因, 而与调幅波长无明确关联; 2) 纳米多层结构中W(Mo) 和Cu膜显现出的辐照耐受性与调幅波长相关, 调幅波长越小, 抗He⁺的辐照性能越强; 3) 在5×10¹⁷ He⁺/cm²注入条件下, 观察到He团簇/泡在纳米结构W(Mo) 和Cu膜中的积聚行为存在明显差异: 在W (Mo) 膜中He团簇/泡的分布与晶粒取向相关, He团簇/泡倾向于沿W (211) 晶面分布; 而Cu膜非晶化且He团簇/泡在其体内呈均匀分布. 关键词： W(Mo)/Cu纳米多层膜 +辐照')" href="#">He⁺辐照 He团簇/泡 相转变     

超短超强激光脉冲辐照超薄碳膜电离状态研究

为了进一步理解极端条件下物质的电离特性, 特别是超短超强激光脉冲辐照超薄靶时等离子体的形成与分布, 本文以超薄碳膜为例, 细致研究了超短超强激光脉冲辐照下原子的离化过程. 分析和比较了强激光场直接作用电离和靶内静电场电离等两种场致电离形式, 在碰撞电离可以忽略的情况下, 发现更多的电离份额是来自靶内静电场的电离方式. 研究了激光脉冲强度对电离的影响, 发现激光脉冲强度越强, 电离速度越快, 产生的高价态离子所占比例也越高.当激光强度为1×10²⁰ W/cm²时, 尽管该强度高于电离生成C⁺⁶所需要的激光强度阈值, 但该激光脉冲并不能将整个靶电离成C⁺⁶离子, 对此本文进行了详细的分析. 在研究激光脉冲宽度的影响时, 发现激光脉宽越小, 电离速度越快, 但越小的激光脉冲电离获得的高价态离子越少.     

金属有机物化学气相沉积生长GaN薄膜的室温热电特性研究

采用金属有机物化学气相沉积技术生长了不同掺杂浓度的GaN薄膜, 并且通过霍尔效应测试和塞贝克效应测试, 表征了室温下GaN薄膜的载流子浓度、迁移率和塞贝克系数. 在实验测试的基础上, 计算了GaN薄膜的热电功率因子, 并且结合理论热导率确定了室温条件下GaN薄膜的热电优值(ZT). 研究结果表明: GaN薄膜的迁移率随着载流子浓度的增加而减小, 电导率随着载流子浓度的增加而增加; GaN 薄膜材料的塞贝克系数随载流子浓度的增加而降低, 其数量级在100–500 μV/K范围内; GaN薄膜材料在载流子浓度为1.60×10¹⁸ cm^-3时, 热电功率因子出现极大值4.72×10^-4 W/mK²; 由于Si杂质浓度的增加, 增强了GaN薄膜中的声子散射, 使得GaN薄膜的热导率随着载流子浓度的增加而降低. GaN薄膜的载流子浓度为1.60×10¹⁸ cm^-3时, 室温ZT达到极大值0.0025.     

Measurements and interpretation of the absorption of 0.35 μm laser radiation on planar targets

We report on experimental plasma absorption of 0.35 μm radiation incident on plane targets. Absorption fractions between 50 and 98% were found for UV pulses of 90 and 450 ps duration on planar CH, nickel, and gold targets for intensities between 10¹³ and 3 × 10¹⁵ W/cm². The results are in agreement with computer calculations using inverse bremsstrahlung absorption and a thermal electron heat flux limiter between 0.03 and 0.06     

铥、铽及铕离子掺杂的BaAl2O4膜的阴极射线发光特性

利用喷雾热解法合成了Tm、Tb及Eu离子掺杂的铝酸钡(BaAl₂O₄)发光膜,研究了合成条件对其结构和发光特性的影响.在退火温度达到700℃时,生成了BaAl₂O₄膜.Tm³⁺和Tb³⁺掺杂的BaAl₂O₄膜分别发蓝光和绿光,而Eu³⁺掺杂的BaAl₂O₄膜的发光既有Eu²⁺的特征发射——宽的蓝光发射带,也有Eu³⁺的特征发射——窄的红光发射峰.BaAl₂O₄:Tm³⁺的发射主峰位于462nm,在电压为5kV和电流密度为57μA/cm²的条件下,其阴极射线发光(CL)亮度可达25cd/m²,效率可达0.11lm/W.BaAl₂O₄:Tb³⁺的发射主峰位于549nm,在相同的条件下,其阴极射线发光亮度可达120cd/m²,效率可达0.55lm/W.BaAl₂O₄:Eu³⁺的发射主峰位于616nm,其阴极射线发光亮度为50cd/m²,效率为0.23lm/W.BaAl₂O₄:Eu²⁺发蓝光,峰值位于452nm,其阴极射线发光亮度为640cd/m²,效率为2.93lm/W.     

Proton conductive amorphous thin films of tungsten oxide clusters with acidic ligands

Three kinds of peroxo-polytungstic acid (PPTA, C-PPTA and N-PPTA) were obtained by reacting hydrogen peroxide with metallic tungsten, tungsten carbide or tungsten nitride, respectively. Polytungstates, C-PPTA and N-PPTA, were found to contain oxalate and nitrate ligands. Their proton conductivities were compared using thin film specimens spin-coated from their water solution. Conductivity of each as-coated film was in the range from 10⁻³ to 10⁻⁴ S cm⁻¹ under the relative humidity of 40% (25 °C). A sharp decrease in conductivity (to less than 10⁻⁷ S cm⁻¹ at 25 °C) was observed for PPTA without acidic ligands after thermal treatment at 80 °C. However, the effect of thermal treatment on C-PPTA or N-PPTA was much milder. A 80 °C-treated C-PPTA film showed the conductivity of 1.0 × 10⁻⁵ S cm⁻¹ (25 °C) with a very weak dependency on ambient humidity.     

Transient thermal lensing measurement in a laser diode pumped NdxY1−xAl3(BO3)4 laser using a holographic shearing interferometer

A new technique for measuring a thermal lens, using a holographic shearing interferometer is presented. This technique was used to measure transient thermal lensing in a laser diode pumped NYAB laser. The measured thermal lensing power was proportional to the pumping laser diode intensity, with a gradient of 1.1 × 10⁻¹ m⁻¹ mm²/W. The transient response time of the thermal lens was 1.5 s, this value being consistent with the temporal decline of the second harmonic power.     

�۱�ѵ�һ������W/Cu �ݶȲ��ϵ��ȹ������Ż�

针对不同体积分布指数p的W/Cu连续功能梯度材料的偏滤器第一壁结构,采用有限元软件计算了8MW.m?2稳态运行热加载以及等离子体破裂条件下1GW.m?2热流冲击下的力学响应。相同稳态加载条件下,W/Cu连续功能梯度材料的最优分布指数与分层梯度材料存在较大差异,其最优等效应力比分层梯度材料要小26%,表现出更优异的性能。在热冲击响应过程中,连续梯度W/Cu材料塑性损伤随p值不同也存在较大变化,其最优p值与其稳态运行时热应力最优p值存在一定差异,从第一壁应用条件考虑,应综合选取,最佳p值在1.2附近。综合来看,连续梯度W/Cu材料具有更连续变化的热物理属性及力学性能,在聚变堆第一壁结构设计中具有更大的应用潜力。     

薄膜硅/晶体硅异质结电池中本征硅薄膜钝化层的性质及光发射谱研究

本文采用甚高频等离子体化学气相沉积技术 (VHF-PECVD) 制备薄膜硅/晶体硅异质结电池中的本征硅薄膜钝化层, 光发射谱 (OES) 测量技术研究了硅薄膜沉积过程中等离子体发光谱随时间的变化. 结果表明: 在实验优化条件下等离子体发光谱很快达到稳定 (大约25 s), 并且SiH^*/H_α^* 的比值随时间变化较小, 避免了生长过程中硅薄膜结构的不均匀性, 这主要是SiH₄没有完全耗尽避免了SiH₄的反向扩散. 进一步研究了沉积参数对稳态发光谱和硅薄膜性质的影响, 结果表明: 随着硅烷浓度增加, H_α^*峰强度减小, SiH^*峰强度增加, 薄膜从微晶转变成非晶, 非晶硅薄膜钝化效果好; 随着沉积气压增大, H_α^*和 SiH^*峰强度先增加后减小, 高气压下H_α^*和 SiH^*峰强度下降主要是反应前驱物的聚合形成高聚合物, 不利于形成高质量的硅薄膜, 因此钝化效果下降; 随着反应功率密度增加, H_α^*和 SiH^*峰强度增大, 当功率密度为150 mW/cm² 趋于饱和, 硅薄膜的致密度和钝化效果也开始下降, 50 mW/cm²的低功率密度下硅薄膜钝化效果差可能是由于原子H 浓度低, 不能完全钝化单晶硅表面的悬挂键. 关键词： 薄膜硅 异质结 光发射谱 钝化     

GaSb基PECVD法制备SiO2薄膜的应力研究

为了实现在GaSb衬底上获得低应力的SiO₂薄膜,研究了等离子体增强化学气相沉积法（PECVD）在晶格失配较大的GaSb衬底上沉积SiO₂薄膜的应力情况。通过改变薄膜沉积时的工艺条件,如反应温度、射频功率、反应压强、气体流量比,并基于曲率法模型,对镀膜前后的曲率半径进行了实验测量,利用Stoney公式计算相关应力值并绘制应力变化曲线。详细讨论了PECVD工艺条件的改变对SiO₂薄膜应力所产生的影响。同时通过在Si衬底上沉积SiO₂薄膜,对比分析了导致薄膜应力产生的因素及变化过程。实验结果表明,在沉积温度为300℃、射频功率为20 W、腔体压强为90 Pa、气体流量比SiH₄/N₂O为125/70 cm³·min^-1的工艺参数下,PECVD法在GaSb衬底上沉积的SiO₂薄膜应力相对较小。     

High performance uncooled InAsSbP/InGaAs photodiodes for the 1.8–3.4 μm wavelength range

Room temperature In_0.97Ga_0.03As photodiodes with an InAs_0.36Sb_0.20P_0.44 transparent window layer operating in the mid-infrared region over the wavelength range 1.8–3.4 μm are reported. The InAs_0.36Sb_0.20P_0.44/In_0.97Ga_0.03As heterojunction photodiodes were grown on p-type (100) InAs substrates by liquid phase epitaxy (LPE). Basic detector characteristics have been measured and compared with other detectors in this wavelength range. The typical detectivity of the photodiodes is 1.2 × 10¹⁰ cm Hz^1/2/W at room temperature, which compares very favourably with that of TE cooled HgCdTe and is at least three times that of cooled PbSe photoconductors. The InAs_0.36Sb_0.20P_0.44/In_0.97Ga_0.03As heterojunction photodiodes offer the advantage of increased sensitivity and extended wavelength response at room temperature compared with that of currently available commercial photodetectors, making them an attractive alternative for a number of mid-infrared applications including optical gas sensors and infrared spectrometers.     

Electron density and temperature contour plots from alaser-produced plasma using collective ultraviolet Thomson scattering

Temporally integrated ultraviolet collective Thomson scattering measurements were performed with frequency-quadrupled Nd:YAG laser radiation on an underdense long-scalelength aluminum plasma (n_c ~10²¹ cm^-3, Z≈7, T_e≈T_i ⩾50 eV, L⩾100 μm). The plasma was preformed by an Nd:YAG fundamental beam (1.06 μm) with focusable intensities of 10 ¹¹ W/cm². Color images of two-dimensional (2-D) spatially resolved (30 μm) electron density and electron temperature were obtained. These are the shortest wavelength Thomson scattering measurements on a plasma to date     

聚变堆第一壁连续W/Cu 梯度材料的热工性能优化

针对不同体积分布指数p的W/Cu连续功能梯度材料的偏滤器第一壁结构,采用有限元软件计算了 8MW•m⁻²稳态运行热加载以及等离子体破裂条件下1GW•m⁻²热流冲击下的力学响应。相同稳态加载条件下,W/Cu 连续功能梯度材料的最优分布指数与分层梯度材料存在较大差异,其最优等效应力比分层梯度材料要小26%,表现出更优异的性能。在热冲击响应过程中,连续梯度W/Cu材料塑性损伤随p值不同也存在较大变化,其最优p值与其稳态运行时热应力最优p值存在一定差异,从第一壁应用条件考虑,应综合选取,最佳p值在1.2附近。综合来看,连续梯度W/Cu材料具有更连续变化的热物理属性及力学性能,在聚变堆第一壁结构设计中具有更大的应用潜力。     

反射式倒装对1 300 nm激光器性能改善的分析

对AlGaInAs多量子阱1 300 nm FP激光器进行反射式倒装封装,在热沉上靠近激光器出光端面约10~20 μm的区域采用Au反射层,对器件垂直方向出光进行反射。测试结果显示,与常规封装相比,采用这种结构封装芯片垂直发散角从34.5°降低至17°,器件单模光纤的平均耦合功率从1 850 μW提高至2 326 μW,耦合效率从21.1%提高到26.5%。对两种激光器进行光电参数的测量,结果表明：与常规封装器件相比,采用反射式倒装结构器件的饱和电流从135 mA提高至155 mA,饱和输出功率从37 mW提高至42 mW,热阻从194 K/W降低至131 K/W。最后对两种器件在95℃环境温度、100 mA电流下进行加速老化实验,老化结果显示：在老化条件下,器件衰退系数从常规封装的4.22×10^-5降低至1.06×10^-5,寿命从5 283 h提高至21 027 h。     

Electron stimulated desorption of CO from Pd1/W(110)

The electron impact behavior of CO adsorbed on Pd₁/W(110) was investigated. The desorption products observed were neutral CO, CO⁺, and O⁺. After massive electron impact residual carbon, C/W = 0.15, but not oxygen was also found, suggesting that energetic neutral O, not detected in a mass analyzer must also have been formed. Formation of β-CO, i.e., dissociated CO with C and O on the surface was not seen. The total disappearance cross section varies only slightly with coverage, ranging from 9 × 10 ⁻¹⁸ cm² at low to 5 × 10⁻¹⁸ cm² at saturation (CO/W = 0.75). The cross section for CO⁺ formation varies from 4 × 10⁻²² cm² at satura to 2 × 10⁻²¹ cm² at low coverage. That for O⁺ formation is 1.4 × 10⁻²² cm² at saturation and 2 × 10⁻²¹ cm² Threshold energies are similar to those found previously [J.C. Lin and R. Gomer, Surf. Sci. 218 (1989) 406] for CO/W(110) and CO/Cu₁/W(110) which suggests similar mechanisms for product formation, with the exception of β-CO on clean W(110). It is argued that the absence or presence of β-CO in ESD hinges on its formation or absence in thermal desorption, since electron impact is likely to present the surface with vibrationally and rotationally activated CO in all cases; β-CO formation only occurs on surfaces which can dissociate such CO. It was also found that ESD of CO led to a work function increase of the remaining Pd₁/W(110) surface of 500 meV, which could be annealed out only at 900 K. This is attributed to surface roughness, caused by recoil momentum of energetic desorbing entities.     

Absolute spectral distribution of soft X-ray emission from laserproduced gold plasma

Quantitative measurement of spectral distribution of soft X-ray emission from laser produced plasmas and estimation of X-ray conversion efficiency are reported. The X-ray emission from planar gold target irradiated by an Nd:glass laser was recorded using a high resolution transmission grating spectrograph. Spectral distribution of X-ray intensity was derived using calibrated film data and a deconvolution procedure to account for contribution of higher diffraction orders. Results of conversion efficiency per unit solid angle, at a laser intensity of ~4×10¹² W/cm² (λ_L = 1.054 μm), for 10< λ <80 Å and in the water window spectral region (23< λ< 44 Å) are presented. A three-fold increase in conversion efficiency was observed for second harmonic laser irradiation (λ_L = 0.527 μm) at an intensity of 8×10¹² W/cm²     

Preparation and characterization of a novel Si-incorporated ceramic film on pure titanium by plasma electrolytic oxidation

A Si-incorporated bioactive ceramic film was prepared on pure titanium by plasma electrolytic oxidation (PEO) in a new bath containing Ca²⁺, H₂PO₄⁻ and SiO₃²⁻. The film was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS). The apatite-induced ability of PEO film was evaluated by soaking in a simulated body fluid (SBF) for various periods. The results showed that Si-incorporated PEO film present a porous microstructure, the pore size is around 1–5 μm. The film mainly consists of anatase and rutile and a small amount of CaHPO₄ and CaO, besides, bioactive compounds such as CaSiO₃ and SiO₂, also exist in the Si-incorporated PEO film. After immersion in SBF for 28 days, not only the surface layer but also the pores inside the Si-incorporated PEO film were completely filled by apatite crystals, whereas on the surface of a benchmark PEO film free of Si just present small piles of apatite crystals. Silicon incorporated into the PEO film provided more heterogeneous nucleation sites for apatite deposition and hence increased remarkably bioactivity of the PEO film.     

Selective formation of ultrathin PbSe on Ag(111)

Two-dimensional (2D) semiconductors, such as lead selenide (PbSe), locate at the key position of next-generation devices. However, the ultrathin PbSe is still rarely reported experimentally, particularly on metal substrates. Here, we report the ultrathin PbSe synthesized via sequential molecular beam epitaxy on Ag(111). The scanning tunneling microscopy is used to resolve the atomic structure and confirms the selective formation of ultrathin PbSe through the reaction between Ag₅Se₂ and Pb, as further evidenced by the theoretical calculation. It is also found that the increased accumulation of Pb leads to the improved quality of PbSe with larger and more uniform films. The detailed analysis demonstrates the bilayer structure of synthesized PbSe, which could be deemed to achieve the 2D limit. The differential conductance spectrum reveals a metallic feature of the PbSe film, indicating a certain interaction between PbSe and Ag(111). Moreover, the moiré pattern originated from the lattice mismatch between PbSe and Ag(111) is observed, and this moiré system provides the opportunity for studying physics under periodical modulation and for device applications. Our work illustrates a pathway to selectively synthesize ultrathin PbSe on metal surfaces and suggests a 2D experimental platform to explore PbSe-based opto-electronic and thermoelectric phenomena.     

快重离子辐照对MoS2热导率的影响研究

利用0.97 GeV的209Bi离子辐照二硫化钼（MoS₂）晶体,辐照注量范围为1×1010～1×1012 ions/cm2,结合原子力显微镜（AFM）观测和Raman光谱分析研究了快重离子辐照对MoS₂热导率的影响。实验结果显示,快重离子辐照在MoS₂中产生了潜径迹,较高激光功率下的Raman测试使样品局部温度升高,导致E_1/2g和A_1g峰随注量增加向低波数方向移动,且峰形展宽。引入了通过改变激光功率测量Raman光谱得到MoS₂热导率的计算方法,获得了不同辐照注量下MoS₂的热导率的定量分析结果,随注量增加,热导率不断降低,从未辐照样品的563 W/mK下降到1×1012 ions/cm2辐照时的132 W/mK。Molybdenum disulphide (MoS₂) was irradiated by 0.97 GeV 209Bi ions with the fluence of 1×1010 to 1×1012 ions/cm2. The irradiation effect on the thermal conductivity of MoS₂ was analyzed by atomic force microscope (AFM) and Raman spectroscopy. The experimental results show that hillock-like latent tracks are observed on irradiated MoS₂ by AFM. The measurement of MoS₂ by Raman spectrometer with high laser power results in the increase of local temperature of MoS₂, which cause the downshift of peaks position and broadening of E_1/2g and A_1g peak. Furthermore, according to Raman spectra measured at different laser power, thermal conductivity of MoS₂ before and after irradiation was calculated, which show that the thermal conductivity of MoS₂ decreases with increasing fluence, from 563 to 132 W/mK for pristine and 1×1012 ions/cm2 irradiated MoS₂, respectively.