用于ps脉冲放大的大口径放电泵浦KrF激光器

 以简单的火花间隙作为放电开关，建立了一种用于ps脉冲激光放大的大口径放电泵浦KrF准分子激光器。该激光器的有效增益口径截面为4cm×3cm，在自由运转情况下最大激光输出能量为1.3J，脉宽20ns。用作ps放大器时，利用光学偏振放大方式获得了激光能量140mJ，脉冲宽度10ps的激光输出。利用XeCl激光泵浦的染料激光作为探针测量了不同放电条件下和不同气分比条件下激光的增益和吸收系数。     

高温合金不同脉宽超快激光作用下多脉冲去除阈值

实验研究了激光脉冲宽度和脉冲个数对镍基高温合金材料去除阈值的影响,分别在290 fs,1 ps和7 ps脉宽的激光下,使用1,10,50,100,300,500和1000个不同能量的激光脉冲辐照高温合金样品表面。实验结果表明,烧蚀坑尺寸会随脉冲数的增加而增加,而脉冲宽度的增加会加大脉冲个数对烧蚀坑直径的影响。通过烧蚀坑直径的平方值与激光脉冲能量之间存在的对数关系,得到了不同脉冲宽度下镍基高温合金的多脉冲材料阈值。3种不同脉宽下的高温合金多脉冲去除阈值都存在显著的累积效应。根据去除阈值计算得到290 fs,1 ps和7 ps脉宽下的累积效应系数分别为0.88,0.86和0.78。     

Ce:KNSBN晶体中ps激光脉冲二波耦合的直接观察与记录

重复频率为82MHz的ps激光脉冲可在慢响应的光折变晶体Ce:KNSBN中实现二波耦合。本文报道用条纹照相机直接记录的实验结果并给出解释。 关键词：     

电子束泵浦KrF激光器进行超短脉冲的单束放大实验研究

 电子束泵浦KrF激光器口径大、泵浦率高，可直接用于进行超短脉冲激光的放大。用天光一号电子束泵浦KrF激光器进行超短脉冲激光放大，将超短脉冲激光放大到2~3J、1.2ps, 激光功率达到2TW。测量了石英窗镜中的非线性吸收系数和超短脉冲激光脉宽的变化。     

增益开关半导体激光器在外光注入下脉冲抖动的实验研究

采用增益开关半导体激光器作为注入种子光源来降低另一个增益开关DFB或Fabry-Perot（FP ）半导体激光器的脉冲抖动.相位噪声测量技术表明：增益开关FP激光器在外部脉冲光注入 下，激光脉冲抖动（均方值）由1.2ps降低至830fs；增益开关DFB半导体激光器在外脉冲注 入下，脉冲抖动由12ps降低至1.8ps. 关键词： 半导体激光器 光脉冲产生 时间抖动 光子注入     

输出2.5J／20PS的高功率钕玻璃激光系统

本文报道一台输出为2.5J/20ps,在0.3mrad内占总能量80％的高功率超短脉冲钕玻璃激光系统;该装置还具有其输出激光脉冲宽度从20ps到2ns大范围内分段可调的性能。     

短脉冲激光刻蚀加工铜材料的机制

 利用数值模拟方法，研究波长1 064 nm、脉冲宽度介于1~20 ps的激光在刻蚀铜靶时，单次脉冲作用下非平衡场刻蚀和热平衡刻蚀两种机制的竞争过程。结果表明：随着脉冲宽度的增加，刻蚀过程由非平衡电荷分离场刻蚀占主导地位转变为热平衡刻蚀起主要作用，且脉冲宽度和激光峰值功率密度增大到一定程度后，各种电子加速机制在不同时刻开始突显，电子能量分布出现多峰结构。在能量密度为15 J/cm2的激光作用下，1和5 ps脉宽对应的非平衡场刻蚀深度分别为110和101 nm，10和20 ps脉宽分别为25和18 nm。     

皮秒和纳秒单脉冲激光加热Al/NC复合纳米含能材料的热动力学分析

对纳米金属颗粒复合含能材料这一新兴体系的单脉冲激光作用的热动力学过程进行了理论分析. 推导了分散在介质中的纳米金属颗粒吸收脉冲激光能量的瞬时功率密度. 从热分解机理出发对纳米金属铝复合硝化纤维(Al/NC)薄膜吸收脉冲激光能量过程以及伴随着放热化学反应的热点热量传播过程进行了数值模拟,计算了不同质量分数的Al/NC薄膜样品分别在100ps,10ns,25ns脉冲激光作用下的化学反应直径. 计算结果与实验数据相比较,表明了热分解基本符合10ns,25ns脉冲激光引发含能材料反应的机理,但它并不符合100ps 关键词： 热分解 化学反应 脉冲激光 含能材料     

条纹相机系统在激光脉冲整形测量中的应用

针对采用脉冲堆积法进行激光脉冲整形后获取的宏脉冲,介绍了基于条纹相机观测其纵向分布的基本原理。阐述了测量系统中的硬件配置功能以及脉冲堆积原理,并描述了使用条纹相机专用软件测量激光脉冲的详细步骤和操作界面。研究了测量系统中时序控制的调试对观测脉冲堆积后的宏脉冲的影响并给出了测量结果和测量误差分析。结果表明:采用脉冲堆积法所获得的激光脉冲整形效果非常理想,整形前激光脉冲的半高全宽值约为3.82 ps,整形后约为15.3 ps,且平顶部分的脉宽为11.5 ps,上升沿和下降沿均为1.9 ps。     

脉宽对中红外激光带内损伤HgCdTe材料的影响

研究了脉宽对于中红外脉冲激光带内损伤碲镉汞（HgCdTe）材料阈值的影响,使用一维自洽模型对激光辐照HgCdTe材料程中的载流子数密度,载流子对数目流,载流子对能流,载流子温度和材料晶格温度等相关参数进行仿真计算。仿真结果表明,波长2.85 μm,脉宽30 ps～10 ns单脉冲激光带内辐照HgCdTe材料的损伤阈值为200～500 mJ/cm2。其中,300 ps～3 ns脉冲激光的损伤阈值相近,均为200 mJ/cm2且低于其他脉宽激光的损伤阈值。搭建实验光路并进行相关实验验证仿真模型的正确性。实验发现,波长2.85 μm、脉宽300 ps的单脉冲激光带内辐照HgCdTe材料的损伤阈值在200 mJ/cm2左右。相同条件下,10 ns单脉冲激光带内辐照HgCdTe材料的损伤阈值约474 mJ/cm2。百皮秒脉冲激光对HgCdTe材料的损伤过程结合了热击穿和光学击穿效应,其独特的毁伤机理加剧了材料的损伤。     

Magnetotransport properties of La0.67Ca0.33MnO3//La0.67Sr0.33MnO3 bilayers

The perovskite bilayers La0.67Ca0.33MnO3 （LCMO） （100 nm） / La0.67Sr0.33MnO3（LSMO） （100 nm） and LSMO （100 nm） / LCMO （100 nm） are fabricated by a facing-target sputtering technique. Their transport and magnetic properties are investigated. It is found that the transport properties between them are different obviously due to distinguishable structures, and the different lattice strains in both films result in the difference of metal-to-insulator transition. Only single-step magnetization loop appears in our bilayers from 5K to 320K, and the coercive force of LSMO/LCMO varies irregularly with a minimum ～ 2387A/m which is lower than that of LCMO and LSMO single layer films. The behaviour is explained by some magnetic coupling.     

Electrical transport and magnetic properties of La2/3Ca1/3MnO3/SiO2 composites

The influence of SiO₂ on the electrical transport properties of LCMO/SiO₂ composites with different SiO₂ contents x is investigated, where LCMO represents La_2/3Ca_1/3MnO₃. Results show that the SiO₂ phase not only shifts the metal–insulator transition temperature (T_p) to a high temperature range, but also has an effect on the magnetoresistance (MR) of the composites. The temperature dependence of resistivity indicates that the T_p of the composites is obviously higher than that of pure LCMO, and that the peak resistivity ρ_max of the composites is lower than that of pure LCMO. In the SiO₂ content x∼0.02, the T_P is the highest and ρ_max becomes the lowest. The experimental observation is discussed on the basis of the analysis of scanning electron microscopy (SEM) images and X-ray diffraction (XRD) patterns. Compared with pure LCMO, a possible interpretation is presented by considering the influence of SiO₂ on the coupling between ferromagnetic (FM) domains of LCMO.     

对靶溅射技术制备的La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜中Tc的降低

本文用对靶溅射技术制备了La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜.与YBCO单层薄膜相比,由于超导/铁磁系统中的磁性邻近效应,三层薄膜表现出较低的超导转变温度.薄膜的R～T测量曲线显示出超磁阻(CMR)效应和超导转变,预示着超导和铁磁特性共存于LCMO/YBCO/LCMO三文治结构.     

La0.8Ca0.2MnO3/SrTiO3薄膜厚度对其结构及磁学性能的影响

采用多种X射线衍射技术和磁电阻测量技术研究了不同厚度的La_0.8Ca_0.2MnO₃/SrTiO₃ (LCMO/STO)薄膜的应变状态及其对磁电阻性能的影响.结果表明，在STO(001)单晶衬底上生长的LCMO薄膜沿［00l］取向生长.LCMO薄膜具有伪立方钙钛矿结构，随着薄膜厚度的增加，面内晶格参数增加，垂直于面内的晶格参数减小,晶格参数a和b相近，略小于c.LC 关键词： X射线衍射 微结构 应变 物理性能     

Influence of microstructures on exchange bias behaviors of La0.7Sr0.3MnO3/La0.33Ca0.67MnO3 bilayers

Ferromagnetic La_0.7Sr_0.3MnO₃ (LSMO) and antiferromagnetic La_0.33Ca_0.67MnO₃ (LCMO) layers were grown on SrTiO₃ (STO) substrates by the pulsed laser deposition technique. LSMO films had rougher surfaces and larger grain sizes than LCMO films. Fully strained bilayers, in which each layer was as thin as 10 nm, were prepared by changing their stacking sequences, i.e. LSMO/LCMO/STO and LCMO/LSMO/STO. The former had higher T_C (350 K) than the latter (300 K), and exchange bias effects were only observed in the former bilayers. This revealed that microstructures could play an important role in the transport and magnetic properties of manganese oxide thin films.     

Response of the capacitance of a planar La0.67Ca0.33MnO3/SrTiO3/La0.67Ca0.33MnO3 heterostructure to an electric field

Manganite film electrodes were integrated with a spacer layer of strontium titanate to produce an epitaxial La_0.67Ca_0.33MnO₃/(1000 nm)SrTiO₃/La_0.67Ca_0.33MnO₃ (LCMO/STO/LCMO) heterostructure by laser ablation. At T = 300 K, the mechanical stresses in the STO layer relaxed to a considerable extent, while the LCMO electrodes were found to be under biaxial lateral tensile strain, with the lattice unit cell of the top electrode distorted considerably stronger (a _∥/a _⊥ ≈ 1.026) than that of the bottom electrode (≈1.008) (a _∥ and a _⊥ are the unit cell parameters in the substrate plane and along the normal to its surface, respectively). The reciprocal of the capacitance C of the plane-parallel LCMO/STO/LCMO film capacitors thus formed increased almost linearly with increasing temperature T in the range 50–250 K. At T < 100 K, the capacitance C decreased by approximately 50% in an electric field E = 40 kV/cm. After the electric field E was varied as 0 → + 100 kV/cm → 0, the capacitance C decreased by approximately 3% and the maximum in the C(E, T > 200 K) dependence shifted by approximately 9 kV/cm with respect to the point E = 0.     

Exchange bias in (1 1 0)-orientated Bi0.9La0.1FeO3/La0.5Ca0.5MnO3 films

We performed a systematic study on the exchange bias in (1 1 0)-orientated Bi_0.9La_0.1FeO₃/La_0.5Ca_0.5MnO₃ (BLFO/LCMO) heterostructure with a fixed BLFO film thickness of 600 nm and different LCMO layers ranging from t=0 to 30 nm. The LCMO is found to be weakly ferromagnetic, with the Curie temperature descending from ∼225 K to 0 as the layer thickness decreases from 30 nm to 3 nm. The main magnetic contributions come from the BLFO film, and the areal magnetization ratio is 1:0.07 for t=5 nm and 1:0.82 for t=30 nm for BLFO to LCMO at the temperature of 5 K. Further experiments show the presence of significant exchange bias, and it is, at the temperature of 10 K, ∼40 Oe for t=0 and ∼260 Oe for t=30 nm. The exchange bias reduces dramatically upon warming and disappears above the blocking temperature of the spin-glasslike behavior observed in the samples. The possible origin for exchange bias is discussed.     

脱氧La0.5Ca0.5MnO3样品的铁磁-反铁磁转变和电阻率变化

研究了氧空位对La_0.5Ca_0.5MnO₃ （LCMO）多晶块材的电输运和磁性质的影响. 随着氧空位的增加, 样品在高温段的电阻率一直增加, 并满足绝热小极化子模型, 而低温段的电阻率先下降后上升, 并出现明显的dR/dT>0的行为, 直至最后变为绝缘的. 氧空位的增加抑止了反铁磁相的出现, 使得脱氧的LCMO样品不发生反铁磁转变, 进一步增加氧空位则会抑制铁磁相. 关键词： 0.5Ca_0.5MnO₃')" href="#">La_0.5Ca_0.5MnO₃ 反铁磁相变 铁磁相变 脱氧     

Thickness dependence of electroresistance in La0.67Ca0.33MnO3 epitaxial films

The electroresistance (ER) of La_0.67Ca_0.33MnO₃ (LCMO) epitaxial thin films with different thicknesses was studied. For the 110 nm thick LCMO film, its ER shows a maximum at T_p, where the resistance shows a peak, and decreases to zero at lower temperatures. While for the 30 nm thick LCMO film, its ER is remarkable in a wide temperature range. Another interesting observation in this work is that the electric current can tune the magnetoresistance of the ultrathin LCMO thin film. The results were discussed by considering the coexistence of ferromagnetic metallic phase with the charge ordered phase, and the variation of the phase separation with film thickness and electric current. This work also demonstrates that electric current can tune the magnetoresistance of the manganites, which is helpful for their applications.     

微纳米加工技术对La2/3Ca1/3MnO3材料性能影响的研究

利用脉冲激光沉积(PLD)方法制备了La2/3Ca1/3MnO3(LCMO)外延薄膜.然后利用微纳米加工技术对LCMO薄膜材料进行了局部改造,制造出宽度仅为83纳米的弱联接结构,并对此进行了一系列的物性改变研究.发现在测量电流不变(1μA)的情况下,R～T曲线在120K附近有一个尖锐的跳变,跳变的温度区间很窄.此外,测量电流和外加磁场的增加,都能对跳变现象产生抑制作用.目前认为这种现象的产生是由于相分离的原因导致的.