Influence of microstructures on exchange bias behaviors of La0.7Sr0.3MnO3/La0.33Ca0.67MnO3 bilayers

Ferromagnetic La_0.7Sr_0.3MnO₃ (LSMO) and antiferromagnetic La_0.33Ca_0.67MnO₃ (LCMO) layers were grown on SrTiO₃ (STO) substrates by the pulsed laser deposition technique. LSMO films had rougher surfaces and larger grain sizes than LCMO films. Fully strained bilayers, in which each layer was as thin as 10 nm, were prepared by changing their stacking sequences, i.e. LSMO/LCMO/STO and LCMO/LSMO/STO. The former had higher T_C (350 K) than the latter (300 K), and exchange bias effects were only observed in the former bilayers. This revealed that microstructures could play an important role in the transport and magnetic properties of manganese oxide thin films.     

Enhancing low-field magnetoresistance of La0.67Ca0.33MnO3 films deposited on anodized aluminium-oxide membranes

In this paper we report a new method to fabricate nanostructured films, La0.67Ca0.33MnO3 （LCMO） nanostructured films have been fabricated by using pulsed electron beam deposition （PED） on anodized aluminium oxide （AAO） membranes, The magnetic and electronic transport properties are investigated by using the Quantum Design physics properties measurement system （PPMS） and magnetic properties measurement system （MPMS）. The resistance peak temperature （Tp） is about 85 K and the Curie temperature （To） is about 250 K for the LCMO film on an AAO membrane with a pore diameter of 20nm. Large magnetoresistance ratio （MR） is observed near Tp. The MR is as high as 85% under 1 T magnetic field. The great enhancement of MR at low magnetic fields could be attributed to the lattice distortion and the grain boundary that are induced by the nanopores on the AAO membrane.     

Response of the capacitance of a planar La0.67Ca0.33MnO3/SrTiO3/La0.67Ca0.33MnO3 heterostructure to an electric field

Manganite film electrodes were integrated with a spacer layer of strontium titanate to produce an epitaxial La_0.67Ca_0.33MnO₃/(1000 nm)SrTiO₃/La_0.67Ca_0.33MnO₃ (LCMO/STO/LCMO) heterostructure by laser ablation. At T = 300 K, the mechanical stresses in the STO layer relaxed to a considerable extent, while the LCMO electrodes were found to be under biaxial lateral tensile strain, with the lattice unit cell of the top electrode distorted considerably stronger (a _∥/a _⊥ ≈ 1.026) than that of the bottom electrode (≈1.008) (a _∥ and a _⊥ are the unit cell parameters in the substrate plane and along the normal to its surface, respectively). The reciprocal of the capacitance C of the plane-parallel LCMO/STO/LCMO film capacitors thus formed increased almost linearly with increasing temperature T in the range 50–250 K. At T < 100 K, the capacitance C decreased by approximately 50% in an electric field E = 40 kV/cm. After the electric field E was varied as 0 → + 100 kV/cm → 0, the capacitance C decreased by approximately 3% and the maximum in the C(E, T > 200 K) dependence shifted by approximately 9 kV/cm with respect to the point E = 0.     

Preparation and study of silver added La0.67Ca0.33MnO3 film

La_0.67Ca_0.33MnO₃ (LCMO) and Ag admixed La_0.67Ca_0.33MnO₃ (Ag-LCMO) polycrystalline films have been prepared on SrTiO₃ single crystal (100) substrates by ultrasonic spray pyrolysis technique. These films are characterized using XRD, SEM, and temperature dependence of resistivity (ρ-T) and ac susceptibility (χ-T). The films are having cubic structure with lattice parameters as 3.890 and 3.885 Å for LCMO and Ag-LCMO films, respectively. The peek in ρ-T curve (T_p) and the ferromagnetic transition temperature (T_C) for the Ag-LCMO film is higher than that of LCMO film. The stability of both the films was tested by repeated measurements of its characteristics over a period of one week after several thermal cycling from room temperature to 77 K. In the LCMO film, the peak in the ρ-T curve (T_p) is found to shift towards lower value and conduction noise of the film increases in the subsequent measurements. In the case of Ag-LCMO the value of T_p, T_C and conduction noise of the film did not change even after several measurements. Silver segregating at the grain boundaries in Ag-LCMO polycrystalline film seems to be responsible for improving the characteristics of Ag-LCMO films.     

Thickness dependence of electroresistance in La0.67Ca0.33MnO3 epitaxial films

The electroresistance (ER) of La_0.67Ca_0.33MnO₃ (LCMO) epitaxial thin films with different thicknesses was studied. For the 110 nm thick LCMO film, its ER shows a maximum at T_p, where the resistance shows a peak, and decreases to zero at lower temperatures. While for the 30 nm thick LCMO film, its ER is remarkable in a wide temperature range. Another interesting observation in this work is that the electric current can tune the magnetoresistance of the ultrathin LCMO thin film. The results were discussed by considering the coexistence of ferromagnetic metallic phase with the charge ordered phase, and the variation of the phase separation with film thickness and electric current. This work also demonstrates that electric current can tune the magnetoresistance of the manganites, which is helpful for their applications.     

Magnetoresistance and transport properties of different impurity doped La0.67Ca0.33MnO3 composite

An enhanced magnetoresistance and a two-fold effect result from impurity dopant were observed in composites of La_0.67Ca_0.33MnO₃/YSZ and La_0.67Ca_0.33MnO₃/Fe₃O₄. Where YSZ represents yttria-stabilized zirconia and the doping level of both YSZ and Fe₃O₄ is 1 mol%. Different electrical and magnetic transport properties, in particular a lower field magnetization behavior, were observed between pure La_0.67Ca_0.33MnO₃ and the impurity doped La_0.67Ca_0.33MnO₃ composites. Compared with pure La_0.67Ca_0.33MnO₃, a possible interpretation is presented by considering the influences of YSZ and Fe₃O₄ on the structure of grain boundaries and/or surfaces of La_0.67Ca_0.33MnO₃grains.     

La0.67Ca0.33MnO3薄膜中的矫顽力随膜厚与衬底的变化

系统研究了衬底为SrTiO3和LaAlO3上的La0.67Ca0.33MnO3薄膜中的矫顽力随厚度和应变的变化。结构分析表明薄膜为（001）方向织构，而且薄膜中的晶粒尺寸随着薄膜厚度的减小而减小。磁测量表明矫顽力先随着膜厚的减小而增加，在t=10-25nm附近到达一极大值。随后，矫顽力随厚度的减小而降低。还得出矫顽力的大小与测量方向有关：t≥25nm (t≤10nm)时，难磁化方向的矫顽力大于（小于）易磁化方向的矫顽力。据此，我们提出：在厚膜（t≥25nm）中，矫顽力变化由畴壁钉扎机制决定；在超薄膜（t≤10nm）中，则与磁畴的形核机制有关。根据t= 5、10、25、400nm的LCMO/STO薄膜的初始磁化曲线，以及t=5，50nm的LCMO/LAO薄膜的小磁滞回线的测量，我们对薄膜中矫顽力机制作了验证，并且还讨论了钉扎和形核机制发生的非均匀区的尺寸。     

Metastable structure and properties of (La0.73Bi0.27)0.67Ca0.33MnO3

The electrical transport and magnetic properties of high Bi doped (La_0.73Bi_0.27)_0.67Ca_0.33MnO₃ are studied at the temperature and magnetic field ranges from 10 to 300 K and 0 to 3 T. Significant temperature and magnetic field hystereses are observed in both resistivity and magnetization measurements. Meanwhile, an enhanced magnetoresistance effect, within a wide temperature window, is obtained in the (La_0.73Bi_0.27)_0.67Ca_0.33MnO₃. The hysteresis and enhanced magnetoresistance are discussed based on an inhomogeneous metastable structure related to the Bi dopant.     

Epitaxial growth La0.67Ca0.33MnO3 thin film by radio frequency sputtering method

Perfect epitaxial growth of La_0.67Ca_0.33MnO₃ (LCMO) thin film has been achieved on (1 0 0) LaAlO₃ (LAO) single crystal substrate by radio frequency sputtering method. X-ray diffraction (XRD) and electron diffraction analysis indicates that La_0.67Ca_0.33MnO₃ film grows epitaxially on LaAlO₃ along [1 0 0] direction of the substrate. The resistivity variation with temperature of the film shows a sharp metal to semiconductor transition peak around 253 K, which is close to that of the target. The magnetoresistance (MR) also reveals high quality epitaxy film characteristic at low temperatures and near the metal to semiconductor transition temperature.     

Magnetocaloric effect in La0.67Sr0.33MnO3 manganite above room temperature

The La_0.67Sr_0.33MnO₃ composition prepared by sol-gel synthesis was studied by dc magnetization measurements. A large magnetocaloric effect was inferred over a wide range of temperature around the second-order paramagnetic-ferromagnetic transition. The change of magnetic entropy increases monotonically with increasing magnetic field and reaches the value of 5.15 J/kg K at 370 K for Δμ0H=5 T. The corresponding adiabatic temperature change is 3.3 K. The changes in magnetic entropy and the adiabatic temperature are also significant at moderate magnetic fields. The magnetic field induced change of the specific heat varies with temperature and has maximum variation near the paramagnetic-ferromagnetic transition. The obtained results show that La_0.67Sr_0.33MnO₃ could be considered as a potential candidate for magnetic refrigeration applications above room temperature.     

Appearance of an inhomogeneous superconducting state in La0.67Sr0.33MnO3-YBa2Cu3O7-La0.67Sr0.33MnO3 trilayers

An experimental study of proximity effect in La_0.67Sr_0.33MnO₃-YBa₂CU₃O₇-La_0.67Sr_0.33MnO₃ trilayers is reported. Transport measurements on these samples show clear oscillations in critical current (I _c) as the thickness of La_0.67Sr_0.33MnO₃ layers (d _F) is scanned from ∼50 ? to ∼ 1100 ?. In the light of existing theories of ferromagnet-superconductor (FM-SC) heterostructures, this observation suggests a long range proximity effect in the manganite, modulated by its weak exchange energy (∼2 meV). The observed modulation of the magnetic coupling between the ferromagnetic LSMO layers as a function of d _F, also suggests an oscillatory behavior of the SC order parameter near the FM-SC interface.      

Electric current-induced giant electroresistance in epitaxial La0.67Sr0.33MnO3 thin films

The electronic transport behavior of La_0.67Sr_0.33MnO₃ epitaxial thin films with different thicknesses has been investigated under various applied DC currents. The 20 and 70 nm thick films show a giant negative electroresistance (ER). In contrast, the films with 100 nm thickness show unusual giant positive ER, which can reach 30% with the current density of 1.8×10⁸ A/cm² at room temperature. It is interesting that the electric current can also change the magnetoresistance of the films. The results were explained by considering the spin polarized current induced increase of ferromagnetic metallic phase and current-induced lattice distortion via electron wind force under high current density.     

Twin-microstructure enhanced magnetoresistance in La0.67Ba0.33MnO3 oxides

The grain growth dependence of microstructure and its effects on magnetic and transport properties are studied in the polycrystalline La_0.67Ba_0.33MnO₃ oxides. It is found that a lateral growth manner along a certain direction and a concentric terrace pattern along three orthogonal axes occur in the samples sintered at 1573 and 1673 K, respectively. Lamella-like twin microstructure forms in the concentric terrace growth pattern and the magnetoresistance properties can be enhanced by the twin microstructure. It suggests that the twin-boundaries in twin-grains may possibly induce spin-dependent scattering of electrons that is field reduced, or spin-polarized tunneling of electrons that is field enhanced, thus strengthening the effect of grain boundaries.     

Ti/Pr0.7Ca0.3MnO3/La0.67Sr0.33MnO3/Pt异质结电致电阻效应的改善

采用脉冲激光沉积技术制备了Ti/Pr_0.7Ca_0.3MnO₃/Pt和Ti/Pr_0.7Ca_0.3MnO₃/La_0.67Sr_0.33MnO₃/Pt异质结并研究了La_0.67Sr_0.33MnO₃功能插层对异质结电致电阻特性的影响. 实验结果表明La_0.67Sr_0.33MnO₃功能层的引入有效提高了器件的电阻转变特性,尤其是电阻转变率和疲劳性得到了极大的改善. 对La_0.67Sr_0.33MnO₃插层改善电致电阻转变特性的机理进行了定性的分析. 关键词： 电致电阻效应 电阻转变比率 疲劳特性     

Structure and magnetic properties of CrN thin films on La0.67Sr0.33MnO3

High crystalline quality CrN thin films have been grown on La_0.67Sr_0.33MnO₃ (LSMO) templates by molecular beam epitaxy. The structure and magnetic properties of CrN/LSMO heterojunctions are investigated combining with the experiments and the first-principles simulation. The Nėel temperature of the CrN/LSMO samples is found to be 281 K and the saturation magnetization of CrN/LSMO increases compared to that of LSMO templates. The magnetic property of CrN/LSMO heterostructures mainly comes from Cr atoms of (001) CrN and Mn atoms of (001) LSMO. The (001) LSMO induces and couples the spin of the CrN sublattice at CrN/LSMO interface.     

La0.33Pr0.34Ca0.33MnO3薄膜的应变效应

采用脉冲激光沉积法分别在(100)LaAlO₃和(100)SrTiO₃基片上生长了La_0.33Pr_0.34Ca_0.33MnO₃薄膜,并通过磁测量和电输运测量对生长在不同基片上的La_0.33Pr_0.34Ca_0.33MnO₃薄膜的物性进行了研究.结果表明,基片和薄膜之间的压应力导致La_{关键词： 钙钛矿锰氧化物 相分离 电荷有序}     

Enhanced ferromagnetic transition temperature in nanocrystalline lanthanum calcium manganese oxide (La0.67Ca0.33MnO3)

We report a novel, low temperature (450-600 °C) route for the synthesis of highly crystalline and homogeneous nanoparticles of lanthanum calcium manganese oxide La_0.67Ca_0.33MnO₃ (LCMO). The nanocrystallites, with average particle size of 30 nm, possess a ferromagnetic-paramagnetic transition temperature (T_c) of 300 K, which is about 50 K higher than that of a bulk single crystal. The transition temperature was found to be inversely proportional to the particle size. The Rietveld analysis of the powder X-ray diffraction data of the phase-pure nanopowders reveals that the particle size reduction leads to a significant contraction of the unit cell volume and a reduction of the unit cell anisotropy. We propose that these two lattice effects are responsible for the observed enhancement in T_c.     

Superparamagnetic behavior of La0.67Sr0.33MnO3 nanoparticles prepared via sol-gel method

Magnetic nanoparticles of La_0.67Sr_0.33MnO₃ (LSMO) manganite were prepared by sol-gel method. Phase formation and crystal structure of the synthesized powder were examined by the X-ray diffraction (XRD) using the Rietveld analysis. The mean particle size was determined by the transmission electron microscopy (TEM). Infrared transmission spectroscopy revealed that stretching and bending modes are influenced by calcinations temperature. The temperature dependence of the ac magnetic susceptibility was measured at different frequencies and ac magnetic fields in the selected ranges of 40-1000 Hz and 80-800 A/m, respectively. The temperature dependence of ac susceptibility shows a characteristic maxima corresponding to the blocking temperature near room temperature. The frequency dependence of the blocking temperature is well described by the Vogel-Fulcher law. By fitting the experimental data with this law, the relaxation time τ₀=1.7×10⁻¹² s, characteristic temperature T₀=262±3 K, anisotropy energy E_a/k=684±15 K and effective magnetic anisotropy constant k_eff=2.25×10⁴ erg/cm³ have been obtained. dc Magnetization measurement versus magnetic field shows that some of LSMO nanoparticles are blocked at 293 K. The role of magnetic interparticle interactions on the magnetic behavior is also investigated.     

Pico-second photoelectric characteristic in manganite oxide La0.67Ca0.33MnO3 films

Ultrafast photoelectric characteristic has been observed in La_0.67Ca_0.33MnO₃ films on tilted SrTiO₃ substrates. A pico-second (ps) open-circuit photovoltage of the perovskite manganese oxide films has been obtained when the films were irradiated by a 1.064μm laser pulse of 25 ps duration. The rise time and full width at half-maximum of the photovoltage pulse are ～300 ps and ～700 ps, respectively. The photovoltaic sensitivity was as large as ～500 mV/mJ.     

Ag掺杂的La0.67Pb0.33MnO3薄膜中激光感生热电电压效应

采用脉冲激光沉积法在倾斜LaAlO₃衬底上制备了Ag掺杂的La_0.67Pb_0.33MnO₃(LPMO)系列薄膜，发现该类薄膜中有激光感生热电电压(LITV)效应.随着掺Ag量x(x为Ag的质量与LPMO的质量之比)从0.00增加到0.10，LPMO薄膜中的LITV信号的响应时间先递减后递增，但始终小于未掺Ag的薄膜，掺Ag量x=0.06时响应时间最小.研究发现LPMO薄膜存在一个最佳厚度，在这一厚度下可使得LITV信号 关键词： 3薄膜')" href="#">LaPbMnO₃薄膜 激光感生热电电压 各向异性Seebeck系数 响应时间