Fe,Ce原子在A1—Fe—Ce非晶合金中的分布

采用Ｘ射线衍射技术研究了Ａ１－Ｆｅ－Ｃｅ合金的非晶结构,发现非晶态合金Ｘ射线强度曲线上都丰在明显的预峰,合金随铁含量增加,预峰和主峰向大角度偏移;合金随铈含量增加,预峰和主峰向小解度偏移。２５０℃时,非晶合金出现铝相晶化,而预峰的形状和位置并未发生改革;４００℃时央预峰消失的位置形成多种化合物相。Ｆｅ原子大部分存在于预峰所对应的Ａ１－Ｆｅ－Ｃｅ原子团簇中,崦Ｃｅ原子大部分无规分布于Ａ１非晶基体中。     

溶胶-凝胶法制备Zn1-xMgxO薄膜及其发光性质

采用溶胶-凝胶工艺在玻璃衬底上制备了Zn1-xMgxO(x=0.1,0.2,0.3,0.4,0.5,0.6,0.7)薄膜。X射线衍射(XRD)谱测试结果发现:在0.10.3时出现MgO立方相。薄膜光致发光谱研究表明紫外发光峰随Mg含量的增加向短波方向移动,且随着退火温度的升高发生明显蓝移,禁带宽度增大。但是退火温度为590℃的样品较560℃样品的发光峰出现红移。     

预注入对Si_(1-x)C_x合金形成的影响

室温下在单晶Si中注入 (0 6— 1 5 )at%的C原子 ,部分样品在C离子注入之前在其中注入2 9Si 离子产生损伤 ,然后在相同条件下利用高温退火固相外延了Si1 -xCx 合金 ,研究了预注入对Si1 -xCx 合金形成的影响 .如果注入C离子的剂量小于引起Si非晶化的剂量 ,在 95 0℃退火过程中注入产生的损伤缺陷容易与C原子结合形成缺陷团簇 ,难于形成Si1 -xCx 合金 ,预注入形成的损伤有利于合金的形成 .随着C离子剂量的增大 ,注入产生的损伤增强 ,预注入反而不利于Si1 -xCx 合金的形成 ,但当注入C原子的浓度超过固相外延的溶解度时 ,预注入的影响可以忽略 .退火温度升高到 10 5 0℃ ,无论预注入还是未预注入样品 ,C含量低的合金相仍然保留 ,而C含量高的合金相大部分消失 .     

GaN1-xPx三元合金的光学与结构特性

对采用金属有机化学气相淀积(MOCVD)技术生长的GaN1-xPx三元合金进行了低温光致发光(PL)和X射线衍射(XRD)测试分析,与来自GaN层的带边发射相比,P的摩尔分数比为0．03,0．11和0．15的GaN1-xPx的光致发光峰分别呈现出了73meV,78meV和100meV的红移,文中将这种红移归因于GaN1-xPx合金具有大的带隙能量弯曲系数。X射线衍射结果表明GaN1-xPx三元合金仍为六方结构晶体,且随着P组份比的增加,GaN1-xPx合金的(0002)衍射峰逐渐向小角度方向移动,即晶格常量变大,同时,(0002)衍射峰谱线不断宽化,说明由于替位式P原子的不规则分布以及部分间隙P原子的影响造成了GaN1-xPx样品的晶格畸变。在GaN1-xPx的光致发光谱及X射线衍射谱中均未观测到相应的有关GaP的峰,表明所生长的高P含量的GaN1-xPx三元合金没有产生明显的相分离。     

非晶态Mg_(70)Zn_(30)合金结构因子的预峰

利用X射线衍射仪对非晶态Mg70 Zn30 合金的结构进行了研究 ,获得了强度曲线、结构因子、双体分布函数和原子间最近邻距离 .结果表明 ,Mg70 Zn30 合金在小Q区间存在强烈的预峰现象 .根据预峰的特性 ,提出了Mg70 Zn30 熔体的结构模型 ,即Mg原子位于中心 ,8个Zn原子位于顶角所形成的简单立方结构模型 .该模型以共享顶点的方式相连接 ,能够满足预峰对Mg—Mg原子间距离的要求 .Mg70 Zn30 非晶合金中预峰的产生是相邻原子团中心Mg原子之间相互关联的表现     

一维Fibonacci系列的X射线衍射峰轮廓的计算

用简单原子层的Fibonacci系列模型,根据振幅-相位关系,计算了其X射线衍射图谱,衍射峰位置在k=2π((m+nτ)/(1+2τ))d^-1,d为平均面间距。衍射峰角宽度β与原子层总厚度D仍满足Scherrer公式:β=0.88λ/Dcosθ。并用振幅-相位图解释了弱衍射峰的强度随原子层数增大时产生起伏的现象。 关键词：     

镁含量和热处理对Zn1-xMgxO薄膜结构和发光性能的影响

采用溶胶-凝胶工艺在玻璃衬底上制备了Zn1-xMgxO(x=0.1,0.2,0.3,0.4,0.5,0.6,0.7)薄膜.X射线衍射谱(XRD)测试结果发现,在0.1相似文献   

烧结β型Ti-Nb合金中由间隙原子引起的Snoek弛豫

用粉末冶金方法制备了不同Nb含量的Ti-Nb合金.用美国TA仪器公司的动力学分析仪Q800以单臂振动模式研究了不同Nb含量和不同热处理以及不同测量参数下的Ti-Nb合金的内耗行为,用X-射线衍射检测了不同样品的微观结构.实验表明,在水淬的和烧结态的Ti-Nb合金的内耗-温度曲线上均发现了弛豫型的内耗峰,这个内耗峰的高度与Nb含量有关,在低Nb含量的Ti-Nb合金样品中不出现,水淬样品内耗峰的最大值出现在Ti-35.4 wt.%Nb (以下称Ti-35.4Nb)的合金中,烧结态样品的内耗峰高度在实验成分范围内单调地随Nb含量而增加.水淬的Ti-35.4Nb合金的弛豫参数分别是激活能H_(wq)=(1.67±0.1) eV和指数前因子τ_(0wq)=1.1×10~(-17±1) s.另外,内耗峰的高度也与热处理有关,水淬的Ti-35.4Nb合金比具有相同成分的烧结态的合金的内耗峰高得多,淬火温度对内耗峰高度也有影响.研究发现,这个内耗峰与Ti-Nb合金中的β相有关,峰高取决于β相的稳定性及其含量,当β相的稳定性降低以及β相的量增加时,峰高增加.水淬Ti-35.4Nb合金中的β相是亚稳状态的β相(β_M),时效时β_M能转变成稳定的α相和稳定β相(β_S),烧结态合金中的β相是β_S.不同热处理状态下Ti-35.4Nb合金样品的微观结构的不同导致了内耗峰高度的差别.从微观结构分析,在淬火的合金中,峰高最大值出现在35 wt.%Nb含量附近的现象是由β相的稳定性和β_M相的量随Nb含量变化引起的.在烧结态的Ti-Nb合金中,峰高单调地随Nb含量的增加而增加的情况是由β_S的量决定的.在循环应力作用下,β_M或β_S相晶格点阵中氧原子的跳动和氧原子与替代原子的相互作用是产生内耗峰的根源.     

硬币材料特征峰幅度的探究

利用X射线实验仪测量了不同模式下单元素金属及多元素合金次级X射线K_α特征峰峰值随入射角及出射角的变化.当入射角与出射角相同时,单元素金属的次级X射线特征峰峰值不随角度的改变而改变;当入射角不变时,单元素金属的次级X射线特征峰峰值随出射角的增大而增大,验证了X射线一次荧光激发的理论.对于多元素FeZn合金,当入射角与出射角相同时,Fe的总X射线荧光强度随出射角的增大而增大,Zn的总X射线荧光强度随出射角的增大而减小;当入射角不变时,Fe的总X射线荧光强度随出射角的增大而增大,而Zn的总X射线荧光强度随出射角的增大呈现先增加后减小的趋势,验证了X射线二次荧光激发的理论.     

基片位置对激光会聚铬原子沉积的影响

为了研究基片位置对激光会聚铬原子沉积的影响,基于原子的粒子运动,采用数值计算对基片切割会聚激光场不同部位时高斯激光驻波场光学势阱、原子运动轨迹和沉积条纹进行了仿真。研究结果充分显示了基片位置对上述三方面的影响。虽然基片会对激光产生衍射,但是无论衍射存在与否,沉积条纹半峰全宽的最小值和中心峰值的最大值都出现在基片表面和激光中轴线重合的位置。此时,衍射将使条纹中心峰值降为非衍射时的0.96倍,同时,半峰全宽增加至非衍射时的1.03倍。另外,仿真结果显示,不管是否考虑衍射,垂直于激光中轴线方向(y方向)上沉积条纹的中心峰值随y值的增加呈现单调减小的趋势,而条纹半峰全宽随y值的增加呈现单调递增的趋势。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.