磁控共溅射法制备的Zn2GeO4多晶薄膜结构及其光致发光研究

用射频磁控共溅射方法在不同温度的单晶硅基片上生长薄膜,然后在800℃真空环境下对薄膜进行退火处理,成功获得了结晶状态良好的Zn₂GeO₄多晶薄膜.利用X射线衍射(XRD),X射线光电子能谱(XPS)和原子力显微镜(AFM)对薄膜进行了结构、成分和形貌分析,研究了基片温度对三者的影响. 结果显示,当基片温度升高到400℃以上时,薄膜中的Zn₂GeO₄晶粒在(220)方向上显示出了明显的择优取向. 当基片温度在500—600℃范围内,有利于GeO₂结晶相的形成. XPS显示薄膜中存在着Zn₂GeO₄,GeO₂,GeO,ZnO四种化合态. 同时,随着基片温度的升高,晶粒尺寸增大且薄膜表面趋于平整. 薄膜的光致发光在绿光带存在中心波长为530和550nm两个峰,应该归因于主体材料Zn₂GeO₄中两个不同的Ge²⁺的发光中心. 关键词： 射频磁控溅射 2GeO₄')" href="#">Zn₂GeO₄ 荧光体     

Ag和Ti底层对[Fe/Pt]n多层膜有序化的影响

利用磁控溅射的方法，在热玻璃基片上制备了以Ag，Ti，Cu，Cr，Pt和Ta为底层的［Fe/Pt］_n多层膜，后经不同温度真空热处理，得到L1₀有序结构的FePt 薄膜（L1₀-FePt）.实验结果表明，以Ag和Ti为底层，通过采用基片加温，同时 利用［Fe/Pt］_n多层膜结构，可以促进FePt薄膜的有序化过程，使FePt-L1_０有序化温度从500℃降低到350℃.在较高的温度下退火，以Ag为底层对薄膜的磁性 能影响较小，而以Ti为底层在高于500℃退火后，矫顽力明显下降.在400℃退火20min后，以 Ag和Ti为底层的样品平行膜面的矫顽力分别达到597kA/m和645kA/m，剩磁比分别达到0.81和 0.94，为将来FePt-L1_０有序相合金薄膜用于未来超高密度磁记录介质打下基础. 关键词： ０-FePt薄膜')" href="#">L1_０-FePt薄膜 有序化温度 底层 多层膜结构     

利用FePt/Au多层膜结构制备垂直磁记录L10-FePt薄膜

利用磁控溅射方法在100℃的MgO单晶基片上制备了［FePt/Au］₁₀多层膜,并研究了采用FePt/Au多层膜结构对FePt薄膜的有序化温度、矫顽力（H_C）、垂直磁各向异性、晶粒尺寸以及颗粒间磁交换耦合作用的影响.磁性测试结果表明：FePt/Au多层膜在退火后具有较高的H_C、良好的垂直磁各向异性、较小的晶粒尺寸且无磁交换耦合作用.截面高分辨电镜分析表明：Au可以缓解MgO和FePt之间较大的晶格错配,从而促进薄 关键词： 0-FePt薄膜')" href="#">L1₀-FePt薄膜 有序化温度 垂直磁各向异性 磁交换耦合作用     

金属Fe薄膜的PLD制备及其非线性光学性质研究

采用脉冲激光沉积（PLD）技术在MgO基片上制备了金属Fe薄膜.利用原子力显微镜研究了不同制备温度对薄膜表面形貌的影响.x射线衍射分析表明沉积温度大于500℃时，Fe薄膜在MgO基片上有很好的结晶性，并有单一取向.通过z扫描方法测量了超薄Fe膜的光学非线性，得到了Fe薄膜的非线性折射率n₂＝709×10^-5cm²/ kW，非线性吸收系数 β＝-552×10^-3cm/W. 关键词： Fe薄膜 非线性 脉冲激光沉积     

基片温度对SiNx薄膜结晶状态及机械性能的影响

利用微波电子回旋共振增强磁控反应溅射法在不同基片温度下制备无氢SiN_x薄膜.通过傅里叶变换红外光谱、透射电子显微镜、台阶仪、纳米硬度仪等表征技术,研究了基片温度对SiN_x薄膜结晶状态、晶粒尺寸、晶体取向等结晶性能以及薄膜的生长速率、硬度等机械性能的影响,并探讨了薄膜结晶性能与机械性能之间的关系.研究结果表明,在基片温度低于300℃时制备的SiN_x薄膜以非晶状态存在,硬度值仅为18GPa左右;基片温度 关键词： x')" href="#">SiN_x 磁控溅射 微观结构 硬度     

单晶和孪晶的Zn0.96Co0.04O稀磁半导体薄膜的制备与研究

采用分子束外延技术分别在不同晶面的蓝宝石（sapphire Al₂O₃）基片上制备了沿c轴生长的Zn_0.96Co_0.04O稀磁半导体薄膜.发现在Al₂O₃（1120）晶面（a面）上薄膜是二维层状外延生长的高质量单晶薄膜,而在Al₂O₃（0001）晶面（c面）上薄膜却具有有趣的孪晶结构,部分区域相互之间有一个30°的面内转动来减少和基片之间的失配度.在孪晶薄膜中存在的这些相互旋转形成的区域界面上会引起载流子强烈的散射作用,导致载流子迁移率的下降和平均自由程的缩短.利用X射线吸收精细结构技术证明了无论单晶还是孪晶的Zn_0.96Co_0.04O薄膜中所有的Co都以+2价替代进入了ZnO的晶格,而没有形成任何杂相.而对其磁性研究发现,孪晶的薄膜样品比高质量的单晶薄膜样品具有大得多的饱和磁矩.这充分说明孪晶薄膜中的铁磁性来源与缺陷有关.我们还对铁磁性耦合机制进行了探讨. 关键词： Co掺杂ZnO 稀磁半导体 X射线吸收精细结构 单晶和孪晶薄膜     

Bi-Sb-Te基热电薄膜温差电池离子束溅射制备与表征

本文采用离子束溅射Bi/Te和Sb/Te二元复合靶,直接制备n型Bi₂Te₃热电薄膜和p型Sb₂Te₃热电薄膜.在退火时间同为1 h的条件下,对所制备的Bi₂Te₃薄膜和Sb₂Te₃薄膜进行不同温度的退火处理,并对其热电性能进行表征.结果表明,在退火温度为150 ℃时,制备的n型Bi₂Te₃关键词： 薄膜温差电池 2Te₃薄膜')" href="#">Sb₂Te₃薄膜 2Te₃薄膜')" href="#">Bi₂Te₃薄膜 离子束溅射     

Er硅酸盐化合物薄膜的相转变和光致发光特性研究

溶胶-凝胶法在Si(100)基片上旋涂法制备铒硅酸盐化合物（Er silicate）薄膜.系统研究了烧结温度和烧结时间对Er silicate薄膜相结构、相转变以及光致发光特性的影响.在1000 ℃以下,薄膜晶体结构为Er₂O₃ 晶体和SiO₂ 非晶的混合物.随着烧结温度增加到1200 ℃,保温时间增加到30 min,薄膜晶体结构转变成(100),(200)和(300)择优取向的Er₂SiO₅相. 关键词： 发光学 光学薄膜 溶胶-凝胶法 铒硅酸盐     

离子注入Zn的Si(001)基片热氧化制备纳米ZnO团簇及其生长行为研究

采用离子注入技术将Zn离子注入Si（001）基片,并在大气环境下加热氧化制备了ZnO纳米团簇.利用电子探针、薄膜X射线衍射仪、原子力显微镜和透射电子显微镜,对注入和热氧化后的薄膜成分、表面形貌和微观结构进行表征,探讨了热氧化温度以及注入剂量对纳米ZnO团簇的成核过程及生长行为的影响.结果表明,Zn离子注入到Si基片表面后形成了Zn纳米团簇,热氧化过程中Zn离子向表面扩散,在表面SiO₂非晶层和Si基片多晶区的界面处形成纳米团簇.热氧化温度是影响ZnO纳米团簇结晶质量的一个重要参数.随着热氧化温度的升高,金属Zn的衍射峰强度逐渐变弱并消失,而ZnO的（101）衍射峰强度逐渐增强.当热氧化温度高于800 ℃以后,ZnO与SiO₂之间开始发生化学反应形成Zn₂SiO₄. 关键词： ZnO纳米团簇 离子注入 微观结构 形貌分析     

双层纳米磁电薄膜模型及分析

以层状磁电复合材料弹性力学模型为基础,建立了自由状态下双层纳米磁电薄膜的弹性力学模型,并以此为基础简单介绍了推导其磁电电压系数表达式的方法.计算了CoFe₂Ｏ₄/Pb（Zr_0．52Ti_0．48）Ｏ₃双层纳米复合薄膜的磁电电压系数理论值,分析结果表明基片对薄膜存在强烈的夹持效应,而且基片对压电与磁致伸缩两相材料间最佳体积比有一定的影响. 关键词： 磁电理论 磁电薄膜 铁电材料 磁致伸缩     

PREPARATION OF a-AXIS ORIENTED YBa2Cu3Ox THIN FILMS

The a-axis oriented YBa₂Cu₃O_x(YBCO) thin films could be grown on (100) SrTiO₃(STO) substrates with STO buffer layers by dc and rf magnetron sputtering either by low-ering the deposition temperature, or by using a self-template technique. For the latter, the resistivity of the thin film at 290K along the substrate [001] direction is about four times larger than that in the [010] direction. The zero resistance temperatures T_c0 are 89 K in both directions. So high quality a-axis oriented YBCO thin films can be prepared by the self-template technique. Also the T_c0 increase monotonously with the reduction of the thickness of the YBCO seed layer.     

高择优取向铌酸锶钡薄膜的射频磁控溅射制备

采用溶胶-凝胶法在(100)Si单晶上预先制备出掺钾(K)的铌酸锶钡(SBN)缓冲层,利用射频磁控溅射法在缓冲层KSBN上沉积出高择优取向的铌酸锶钡薄膜,获得了磁控溅射法制备择优取向铌酸锶钡薄膜的相关工艺参数,研究发现,KSBN缓冲层能够很有效地克服衬底与SBN薄膜之间较大的晶格失配,在氧气氩气的比例为1∶2,工作气压为10 Pa,溅射功率300 W,衬底温度300℃,退火温度为800℃的工艺条件下,能够获得c轴高度择优取向的铌酸锶钡铁电薄膜.利用X射线衍射仪,原子力显微镜等仪器分析了薄膜 关键词： 磁控溅射 高择优取向 p-n结效应     

PREPARATION OF a-AXIS ORIENTED YBa2Cu3Ox THIN FILMS

The a-axis oriented YBa₂Cu₃O_x(YBCO) thin films could be grown on (100) SrTiO₃(STO) substrates with STO buffer layers by dc and rf magnetron sputtering either by low-ering the deposition temperature, or by using a self-template technique. For the latter, the resistivity of the thin film at 290K along the substrate [001] direction is about four times larger than that in the [010] direction. The zero resistance temperatures T_c0 are 89 K in both directions. So high quality a-axis oriented YBCO thin films can be prepared by the self-template technique. Also the T_c0 increase monotonously with the reduction of the thickness of the YBCO seed layer.     

Composition, structure and magnetic properties of sputter deposited Ni-Mn-Ga ferromagnetic shape memory thin films

Polycrystalline Ni-Mn-Ga thin films were deposited by the d.c. magnetron sputtering on well-cleaned substrates of Si(1 0 0) and glass at a constant sputtering power of 36 W. We report the influence of sputtering pressure on the composition, structure and magnetic properties of the sputtered thin films. These films display ferromagnetic behaviour only after annealing at an elevated temperature and a maximum saturation magnetization of 335 emu/cc was obtained for the films investigated. Evolution of martensitic microstructure was observed in the annealed thin films with the increase of sputtering pressure. The thermo-magnetic curves exhibited only magnetic transition in the temperature range of 339-374 K. The thin film deposited at high sputtering pressure of 0.025 mbar was found to be ordered L2₁ austenitic phase.     

磁控溅射ZnO薄膜生长的等离子体发射光谱研究

通过反应磁控溅射过程中的等离子体发射光谱，研究了制备ZnO薄膜的沉积温度、氧气流量比例R=O₂/(O₂+Ar)对Zn和O原子发射光谱的影响，并结合ZnO薄膜的结构和物理性能，探讨了沉积温度在ZnO薄膜生长中的作用.研究结果显示：当R≥0.75%时， Zn的溅射产额随R的增加基本呈线性下降规律.当R介于10%—50%时，氧含量的变化相对平缓，有利于ZnO薄膜生长的稳定性控制.Zn原子发射光谱强度随沉积温度的变化可以分为三个阶段.当沉积温度低于250℃时，发射光谱强 关键词： ZnO 薄膜生长 反应磁控溅射 等离子体发射光谱     

Thin film solid oxide fuel cells

We have investigated the deposition of 91% ZrO₂ − 9% Y₂O₃ thin films by a variety of sputtering techniques for the application as electrolytes in thin film solid oxide fuel cells. The deposition by RF sputtering was accomplished by using an oxide target of the desired composition. The deposition rate in these initial tests was limited to 0.5 μm/hr and the morphology of the film was substantially modified by deposition rate and substrate temperature. Using DC magnetron sputtering we deposited metallic films from a metallic target with the desired chemical composition. We introduced oxygen into the sputtering chamber to reactively deposit the desired 91% ZrO₂ − 9% Y₂O₃ thin films; however, we encountered problems with target oxidation and growth rate reproducibility. We subsequently demonstrated that controlled oxidation of the metallic films could result in adhering, non porous yttria stabilized zirconia films. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Electrostatic spray deposition of Gd0.1Ce0.9O1.95 and La0.9Sr0.1Ga0.8Mg0.2O2.87 thin films

The deposition of gadolinia-doped ceria (CGO, Gd_0.1Ce_0.9O_1.95) and LaGaO₃-based perovskite oxides (LSGM, La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.87) thin films on a stainless steel substrate was studied using the electrostatic spray deposition (EDS) technique. The effect of process conditions, such as deposition temperature, deposition time and liquid flow rate, on the surface morphology and microstructure of thin films was examined with scanning electron microscopy (SEM) and powder X-ray diffraction (XRD). The deposited CGO films with a highly porous and three-dimensional interconnected structure were obtained at a liquid flow rate of 0.5 ml/h, a deposition temperature of 503 K and a deposition time ranging from 0.5 to 1 h. On the other hand, the deposited LSGM thin films with porous microstructure were also obtained at the deposition time of 1 h, the deposition temperature of 533 K and the liquid flow rate of 0.5 ml/h. The deposited CGO and LSGM thin films were amorphous at the used deposition temperature. Subsequently, the samples were annealed at 1173 K for 2 h and the desired crystal structures were obtained. The chemical analysis of the thin films was investigated by energy dispersive X-ray (EDX) analysis. The observed chemical compositions of the samples were in a fair agreement with those of the starting solutions.     

Effects of oxygen partial pressure and substrate temperature on the structure and optical properties of MgxZn1−xO thin films prepared by magnetron sputtering

Deposited with different oxygen partial pressures and substrate temperatures, Mg_xZn_1−xO thin films were prepared using a Mg_0.6Zn_0.4O ceramic target by magnetron sputtering. The structural and optical properties of the prepared thin films were investigated. The X-ray diffraction spectra reveal that all the films on quartz substrate are grown along (2 0 0) orientation with cubic structure. The lattice constant decreases and the crystallite size increases with the increase of substrate temperature. Both energy dispersive X-ray spectroscopy and calculated results suggest the ratio of Mg/Zn increases with increasing substrate temperature. The thin film deposited with T_s = 500 °C has a minimal rms roughness of 7.37 nm. The transmittance of all the films is higher than 85% in the visual region. The optical band gap is not sensitive to the oxygen partial pressure, while it increases from 5.63 eV for T_s = 100 °C to 5.95 eV for T_s = 700 °C. In addition, the refractive indices calculated from transmission spectra are sensitive to the substrate temperature. The photoluminescence spectra of Mg_xZn_1−xO thin films excited by 330 nm ultraviolet light indicate that the peak intensity of the spectra is influenced by the oxygen partial pressure and substrate temperature.     

Deposition of NiFe(200) and NiFe(111) textured films onto Si/SiO<Subscript>2</Subscript> substrates by DC magnetron sputtering

The effect of substrate temperature T_sub and bias voltage U_bias on the texture of NiFe films with thickness d ～ 30–340 nm deposited by DC magnetron sputtering onto Si(111)/SiO₂ substrates under working gas pressure ～ 0.2 Pa has been investigated. It has been demonstrated that films grown at room substrate temperature have the (111) texture that is refined under a negative bias voltage. The deposition of films onto a grounded (U_bias ～ 0) substrate heated to T_sub ～ 440–640 K results in the formation of textured NiFe(200) films.     

Nanostructure of photocatalytic TiO2 films sputtered at temperatures below 200 °C

The article reports on correlations between the process parameters of reactive pulsed dc magnetron sputtering, physical properties and the photocatalytic activity (PCA) of TiO₂ films sputtered at substrate surface temperature T_surf ≤ 180 °C. Films were deposited using a dual magnetron system equipped with Ti (Ø50 mm) targets in Ar + O₂ atmosphere in oxide mode of sputtering. The TiO₂ films with highly photoactive anatase phase were prepared without a post-deposition thermal annealing. The decomposition rate of the acid orange 7 (AO7) solution during the photoactivation of the TiO₂ film with UV light was used for characterization of the film PCA. It was found that (i) the partial pressure of oxygen pO₂ and the total sputtering gas pressure p_T are the key deposition parameters influencing the TiO₂ film phase composition that directly affects its PCA, (ii) the structure of sputtered TiO₂ films varies along the growth direction from the film/substrate interface to the film surface, (iii) ∼500 nm thick anatase TiO₂ films with high PCA were prepared and (iv) the structure of sputtered TiO₂ films is not affected by the substrate surface temperature T_surf when T_surf < 180 °C. The interruption of the sputtering process and deposition in long (tens of minutes) pulses alternating with cooling pauses has no effect on the structure and the PCA of TiO₂ films and results in a decrease of maximum value of T_surf necessary for the creation of nanocrystalline nc-TiO₂ film. It was demonstrated that crystalline TiO₂ films with high PCA can be sputtered at T_surf ≤ 130 °C. Based on obtained results a phase zone model of TiO₂ films was developed.