聚硅氧烷/丙烯酸酯核/壳复合胶乳的粒径分布与成核机理

通过种子乳液法合成出具有高有机硅含量核 壳结构的聚硅氧烷 丙烯酸酯复合粒子 .研究了聚合方法、乳化剂浓度、引发剂浓度、单体滴加速度等工艺条件对复合乳液粒径尺寸、分布与形态的影响 ,并对复合乳液的成核机理进行了探讨 .研究表明 ,乳化剂浓度对乳液粒子的粒径分布和形态、结构有显著影响 ,引发剂浓度增加将使粒子粒径减小 ;相对一次投料法 ,种子乳液法生成的粒子分布窄 ,具有明显核壳结构 ,通过壳层单体滴加速度可以控制粒子的粒径尺寸和分布 ;而壳层丙烯酸酯聚合物主要是在聚硅氧烷种子表面的“过渡层”聚合、富集而成 .     

核/壳乳液聚合工艺中乳化剂的定量研究

以十二烷基硫酸钠(SDS)为乳化剂,采用多步种子乳液聚合方法制备了核/壳结构乳液,研究了乳化剂加入量以及加料速率对核壳乳液聚合的影响,并推导了核及壳乳液聚合阶段所需乳化剂量的计算公式.研究表明,当种子、核、壳乳液聚合阶段单体量分别为12g、50g和50g,种子乳液聚合阶段加入的乳化剂量为0.44g时,控制核、壳乳液聚合阶段乳化剂的加入量分别在0.64～2.07g及0.04～2.12g之间,且预乳化单体的滴加速度低于2.3g/min时,可以防止二次成核及新乳胶粒子的形成,制得粒径分布窄、核/壳结构明显的乳胶粒子.利用透射电镜(TEM)对所制备的核壳结构乳胶粒子的结构形态进行了验证,试验结果与理论预测结果一致.     

含氟共聚乳液改善浸渍滤纸抗水抗油性的研究

用核/壳乳液聚合工艺,通过改变单体组成、设计乳胶粒子的形态结构和在乳胶粒子的壳层中引入含氟丙烯酸酯单体,制备具有核/壳结构的含氟丙烯酸酯的共聚乳液。并通过FTIR1、3C-NMR、TEM等手段对共聚乳液的化学结构以及乳胶粒子形态结构进行了表征。同时研究了含氟单体种类和用量、乳化剂种类以及单体加料方式对其聚乳液性能以及浸渍滤纸抗水/油性的影响。     

SiO2/聚甲基丙烯酸叔丁酯核壳复合微粒的制备与表征

以甲基丙烯酸-3-(三甲氧基硅基)丙酯(MPS)修饰的SiO2胶体粒子为种子,甲基丙烯酸叔丁酯(tBMA)为单体、十二烷基硫酸钠(SDS)为乳化剂,采用种子乳液聚合法制备了SiO2/聚甲基丙烯酸叔丁酯的核壳复合微粒。微粒经水解后形成具有pH敏感性的无机/有机复合微粒。研究了影响核壳复合微粒形态结构的因素,结果发现,控制SiO2种子乳液的质量分数在1.5%～2%,可避免聚合过程中生成纯聚甲基丙烯酸叔丁酯乳胶粒子;反应体系中乳化剂SDS的用量超过质量分数0.3%时,易形成纯聚合物乳胶粒子;SDS用量低于质量分数0.15%时,生成的核壳复合微粒易产生团聚;单体和交联剂用量升高,核壳复合微粒的壳层厚度增加,用量过高会导致核壳复合微粒出现团聚现象,并且有纯聚合物乳胶粒子生成。采用TEM、NMR和FTIR及接触角测试技术分析结果表明,复合微粒是由SiO和聚甲基丙烯酸叔丁酯组成的核壳结构微粒。     

核壳型聚丙烯酸酯乳胶粒子及其乳液的研究进展

综述了目前制备核壳型聚丙烯酸酯乳胶粒子的常用方法,如种子乳液聚合法、无皂乳液聚合法、反相乳液聚合法、细乳液聚合法以及种子分散聚合法;分析了聚合工艺、单体种类、温度、乳化剂和引发剂种类及用量等因素对聚丙烯酸酯核壳乳液合成及性能的影响;并对聚丙烯酸酯核壳乳液的研究现状进行了归纳;最后,展望了聚丙烯酸酯核壳乳液的发展方向。     

核-壳复合微球的异相凝聚及其表面包覆率调控

提出了一种通过乳化剂复配简便制备表面包覆率可调的核-壳复合微球的方法.高效液相色谱和zeta电位测试结果表明,核粒子和壳粒子在分散混合过程中出现了乳化剂吸附和脱附的再平衡现象,从核粒子表面游离的阳离子乳化剂与壳粒子表面的阴离子乳化剂发生电性中和作用,导致核、壳2种粒子的zeta电位值互相接近,基于静电作用的异相凝聚失效.进一步研究发现,在保持核粒子分散液中乳化剂总量为1 wt%的前提下,添加非离子乳化剂既可以确保分散体系的稳定性,又可以调控阳离子乳化剂的游离量,成功实现核-壳复合微球的异相凝聚.由此可见,通过调节复配乳化剂中阳离子与非离子乳化剂的配比,可简便地调控复合微球的表面包覆率.还探讨了异相凝聚体系中pH值和电解质浓度对核-壳复合微球表面包覆率的影响.     

含氟/硅丙烯酸酯核壳型乳液的合成及性能

采用半连续种子乳液聚合法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 合成了以丙烯酸丁酯(BA)为核, 以甲基丙烯酸甲酯(MMA)、甲基丙烯酸十二氟庚酯(DFHMA)、3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPTMS)和甲基三甲氧基硅烷(MTMS)为壳的核壳型含氟/硅丙烯酸酯聚合物乳液. 利用FTIR, TEM, SEM-EDX和DSC等手段对乳液组成、乳胶粒子结构、膜表面及断面形态等进行了表征, 讨论了氟/硅含量对聚合物膜性能的影响. 结果表明, 核-壳粒子尺寸为20~30 nm, 乳液膜的性能与膜表面氟和硅的含量及相容性有较大的相关性, 当m(氟)∶m(硅单体)=3∶1时, 形成的膜均匀透明, 吸水率较低, 尺寸稳定性较好.     

核-壳结构的氯化银/聚丙烯酰胺复合纳米粒子的制备与表征

用反相微乳液作为模板制备了核-壳结构的氯化锯／聚丙烯酰胺(AgCI／PAM)复合纳米粒子。透射电镜(TEM)证实复合粒子为核-壳结构，平均直径约100nm。扫描电子显微镜(SEM)和X射线衍射分析显示，平均粒径约50nm的AgCl均匀分散在聚合物中。FTIR谱图表明：AgO与PAM之间存在较强的相互作用。用能级探洲光谱(Energy Detected Spectrum，EDS)和润湿分散实验比较了不同方法改性的复合粒子的表面结构与润湿性能。     

氧化—还原低温引发苯乙烯／丙烯酸丁酯细乳液聚合粒度分 …

用氧化还原引发剂（ＮＨ４）２Ｓ２Ｏ８／ＮaＨＳＯ３研究了苯乙烯（Ｓt）低温下的细乳液共聚合，细乳液单体液滴在亚微米级（１００～４００ｎｍ），测定了过程中粒子大小及分布的变化，发现细乳液聚合随引发剂、乳化剂和共乳化剂浓度的增加，乳胶粒子尺寸变小，分布变宽，并且比相同条件下传统乳液聚合的粒子大。计算了聚合过程中粒子数变化规律及乳化剂覆盖率，讨论了细乳液与传统乳液中引发剂、乳化剂对反应过程的影响及成核机理     

反应性复合乳液的合成、表征及其交联反应

利用种子半连续乳液聚合方法合成了核层或壳层带有环氧基以及壳层带有羧基的3种不同核/壳结构的乳胶粒子,通过物理共混带环氧基和羧基的乳胶粒子,得到了两种反应性复合乳液.利用透射电镜和激光动态光散射对乳胶粒子进行了表征,其粒径分布较窄,粒径分布的多分散系数为0.062,平均粒径约76 nm,乳胶粒子具有明显的核/壳结构.通过胶膜的凝胶率和膨胀率的测定和红外光谱分析对反应性复合乳液中乳胶粒子的扩散及交联反应进行了研究,并探讨了不同核壳结构复合乳液对涂膜机械性能的影响.研究表明,当反应性复合乳液中的环氧基和羧基分别分布在乳胶粒子的核层和壳层时,有利于聚合物分子链的充分扩散和化学交联反应的进行,从而提高涂膜的物理化学性能,当甲基丙烯酸缩水甘油酯(GMA)含量为10 wt%时,涂膜的拉伸强度达20.3 MPa.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.