氯丁胶乳-聚甲基丙烯酸甲酯复合乳胶粒结构形态

以氯丁胶乳（Pa）为种子乳液,甲基丙烯酸甲酯（Pb）为第二单体,采用种子乳液聚合法,制备了氯丁胶乳-聚甲基丙烯酸甲酯复合乳胶粒。 热力学分析表明,当Pb的体积分数Φb＜0.69时,可同时形成Pa-Pb型正核-壳和（Pa＋Pb）分离型乳胶粒,当Φb＞0.69时,形成Pb-Pa型翻转型核壳结构乳胶粒,并伴有Pa-Pb型正核-壳结构乳胶粒的形成。 动力学分析表明,引发剂类型、第二单体的加入方式、种子乳胶粒的交联、单体/聚合物质量比是影响乳胶粒形态的主要因素。 采用水溶性引发剂过二硫酸钾（KPS）,以饥饿态方式加入单体,氯丁胶乳 聚甲基丙烯酸甲酯(PCR-PMMA)复合乳胶粒呈现正核-壳结构,以充溢态方式加入单体则不能形成明显的核-壳结构;而以油溶性偶氮二异丁腈（AIBN）为引发剂时,单体无论以充溢态方式加入还是饥饿态加入均倾向于形成翻转核-壳型粒子。 在种子乳胶粒中加入一定量交联剂二缩三乙二醇二甲基丙烯酸酯,有利于形成明显的正核壳结构。 以饥饿态进料,KPS为引发剂时,随着单体用量增加,壳层变厚,仍呈正核-壳结构,与热力学分析结果相吻合;以AIBN为引发剂时,随着单体用量增加,PCR-PMMA复合乳胶粒逐渐由翻转核壳型结构变为互穿结构。     

核/壳乳液聚合工艺中乳化剂的定量研究

以十二烷基硫酸钠(SDS)为乳化剂,采用多步种子乳液聚合方法制备了核/壳结构乳液,研究了乳化剂加入量以及加料速率对核壳乳液聚合的影响,并推导了核及壳乳液聚合阶段所需乳化剂量的计算公式.研究表明,当种子、核、壳乳液聚合阶段单体量分别为12g、50g和50g,种子乳液聚合阶段加入的乳化剂量为0.44g时,控制核、壳乳液聚合阶段乳化剂的加入量分别在0.64～2.07g及0.04～2.12g之间,且预乳化单体的滴加速度低于2.3g/min时,可以防止二次成核及新乳胶粒子的形成,制得粒径分布窄、核/壳结构明显的乳胶粒子.利用透射电镜(TEM)对所制备的核壳结构乳胶粒子的结构形态进行了验证,试验结果与理论预测结果一致.     

核壳型含氟丙烯酸酯共聚物的合成及性能

采用饥饿态半连续种子乳液聚合方法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 分别选用甲基丙烯酸三氟乙酯(TFEM)、甲基丙烯酸六氟正丁酯(HFBM)和甲基丙烯酸十二氟庚酯(DFHM)为含氟单体, 合成以丙烯酸正丁酯(BA)、甲基丙烯酸甲酯(MMA)和含氟单体为原料的核壳型结构含氟丙烯酸酯共聚物乳液. FTIR, 1H NMR, TEM和DSC分析结果显示, 获得了BA/MMA/含氟单体的共聚物乳液, 且乳液具有明显的核壳结构. DSC, TGA和SEM-EDX的分析显示, 核壳型结构的共聚物具有优异的热力学稳定性能和成膜性能; 长侧链或短侧链含氟单体对共聚物的热稳定性影响不明显, 但侧链较长的含氟单体所获得的聚合物在成膜过程中更易向表面迁移, 更能体现含氟聚合物的优点.     

核壳结构三元含氟丙烯酸酯乳液的制备及表征

以甲基丙烯酸三氟乙酯(Actyflon-G03)、丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)为原料,采用质量比为 1/1 的 OP-10/SDS 复合乳化荆,利用种子乳液聚合法,合成了核壳结构共聚物乳液.研究了温度对聚合反应、氟单体含量对聚合物膜吸水性及硬度的影响,采用 DSC、SEM-EDX、TEM 表征了共聚物膜的性能及乳胶粒子特征.结果表明:当 Actyflon-G03 含量为 23.28%时,核壳型结构粒子呈球形分布,粒径约为 80～110 nm,膜吸水率最低,硬度最高,并有 75.85%的最大转化率和 0.58%的最低凝胶率.SEM-EDX 分析显示,氟原子在成膜过程中向膜表面迁移,降低了膜的表面能.     

含氟/硅丙烯酸酯核壳型乳液的合成及性能

采用半连续种子乳液聚合法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 合成了以丙烯酸丁酯(BA)为核, 以甲基丙烯酸甲酯(MMA)、甲基丙烯酸十二氟庚酯(DFHMA)、3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPTMS)和甲基三甲氧基硅烷(MTMS)为壳的核壳型含氟/硅丙烯酸酯聚合物乳液. 利用FTIR, TEM, SEM-EDX和DSC等手段对乳液组成、乳胶粒子结构、膜表面及断面形态等进行了表征, 讨论了氟/硅含量对聚合物膜性能的影响. 结果表明, 核-壳粒子尺寸为20~30 nm, 乳液膜的性能与膜表面氟和硅的含量及相容性有较大的相关性, 当m(氟)∶m(硅单体)=3∶1时, 形成的膜均匀透明, 吸水率较低, 尺寸稳定性较好.     

核壳型聚丙烯酸酯乳胶粒子及其乳液的研究进展

综述了目前制备核壳型聚丙烯酸酯乳胶粒子的常用方法,如种子乳液聚合法、无皂乳液聚合法、反相乳液聚合法、细乳液聚合法以及种子分散聚合法;分析了聚合工艺、单体种类、温度、乳化剂和引发剂种类及用量等因素对聚丙烯酸酯核壳乳液合成及性能的影响;并对聚丙烯酸酯核壳乳液的研究现状进行了归纳;最后,展望了聚丙烯酸酯核壳乳液的发展方向。     

PMMA-PAN核壳结构复合乳胶的制备与表征

采用疏水引发剂引发的半连续无皂乳液聚合法,合成了Z均流体力学直径约70nm的聚甲基丙烯酸甲酯(PMMA)纳米乳胶。以PMMA纳米乳胶为种子,采用疏水引发剂引发的种子乳液聚合法,制备了PMMA-聚丙烯腈(PAN)核壳结构复合乳胶。采用动态光散射、傅里叶红外光谱、扫描电镜和透射电镜表征了各种乳胶粒的组成、尺寸、结构和微观形态。研究了反应温度、单体用量和表面活性剂用量对PMMA-PAN复合乳胶粒的结构和形态的影响。结果表明:PMMAPAN复合乳胶粒为核壳结构,其壳层厚度可通过改变单体用量进行调整。     

聚硅氧烷/丙烯酸酯核/壳复合胶乳的粒径分布与成核机理

通过种子乳液法合成出具有高有机硅含量核 壳结构的聚硅氧烷 丙烯酸酯复合粒子 .研究了聚合方法、乳化剂浓度、引发剂浓度、单体滴加速度等工艺条件对复合乳液粒径尺寸、分布与形态的影响 ,并对复合乳液的成核机理进行了探讨 .研究表明 ,乳化剂浓度对乳液粒子的粒径分布和形态、结构有显著影响 ,引发剂浓度增加将使粒子粒径减小 ;相对一次投料法 ,种子乳液法生成的粒子分布窄 ,具有明显核壳结构 ,通过壳层单体滴加速度可以控制粒子的粒径尺寸和分布 ;而壳层丙烯酸酯聚合物主要是在聚硅氧烷种子表面的“过渡层”聚合、富集而成 .     

光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。 通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。 结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1.25%时,乳胶膜具有较好的光致变色性能。     

核壳型聚丙烯酸丁酯/聚(苯乙烯-甲丙烯酸甲酯)乳胶粒子形态设计及模拟

在简化及限制的实验条件下，提出了一套界面张力的简化推算方法，通过计算证实了采用该简化算法所得界面张力可较为准确地预测丙苯体系复合乳胶粒子的热力学平衡形态．并且根据性能要求，通过界面自由能变化最小的热力学判据对核壳型聚丙烯酸丁酯／ 聚（ 苯乙烯 甲基丙烯酸甲酯） 复合乳胶粒子进行形态设计，采用种子半连续乳液聚合法制备复合乳胶，利用电镜对设计粒子的最终核壳形态进行了证实．     

单分散P(St-BA-AN)/PANI核壳结构复合微球的制备与电性能

以苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为单体, 采用乳液聚合的方法制备出单分散苯乙烯-丙烯酸丁酯-丙烯腈三元共聚物[P(St-BA-AN)]种子微球, 再在该种子微球表面包覆聚苯胺(PANI), 制得P(St-BA-AN)/PANI核壳结构复合微球. 采用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外透射光谱(FTIR)和漫反射光谱等测试手段对所制备的种子微球和复合微球的形态、结构和形成机理进行了研究, 并用四探针法测定了核壳结构复合物的导电性. 研究结果表明, 通过改变种子乳液共聚物的组成和加入苯胺的量及氧化剂的量等条件可调控复合微球的电导率. 与P(St-BA)/PANI核壳结构复合微球相比, 在核组成中引入了氰基的P(St-BA-AN)/PANI核壳结构复合微球的电导率明显提高, 当加入苯胺的量为P(St-BA-AN)种子微球与苯胺单体总质量分数的40%时, 其电导率可达到0.71 S/cm. 红外光谱结果证实了P(St-BA-AN)种子微球中的氰基和壳层中聚苯胺的胺基之间存在某种相互作用, 导致核壳结构复合物电导率的提高.     

Preparation of Silica/Poly(tert‐butylmethacrylate) Core/Shell Nanocomposite Latex Particles

Nanocomposite latex particles, with a silica nanoparticle as core and crosslinked poly(tert‐butylmethacrylate) as shell, were prepared in this work. Silica nanoparticles were first synthesized by a sol‐gel process, and then modified by 3‐(trimethoxysilyl)propyl methacrylate (MPS) to graft C?C groups on their surfaces. The MPS‐modified silica nanoparticles were characterized by elemental analysis, FTIR, and ²⁹Si NMR and ¹³C‐NMR spectroscopy; the results showed that the C?C groups were successfully grafted on the surface of the silica nanoparticles and the grafted substance was mostly the oligomer formed by the hydrolysis and condensation reaction of MPS. Silica/poly(tert‐butylmethacrylate) core/shell nanocomposite latex particles were prepared via seed emulsion polymerization using the MPS‐modified silica nanoparticle as seed, tert‐butylmethacrylate as monomer and ethyleneglycol dimethacrylate as crosslinker. Their core/shell nanocomposite structure and chemical composition were characterized by means of TEM and FTIR, respectively, and the results indicated that silica/poly(tert‐butylmethacrylate) core/shell nanocomposite latex particles were obtained.     

Synthesis and Characterization of Large Dimension PBA-P(MMA-ITA) Latex Particles with Core-Shell Morphology

In this paper, a novel large dimension poly(n-butyl acrylate)-poly(methyl methacrylate-itaconic acid) (PBA-P(MMA-ITA)) core-shell latex particles (CSR) with diameter of 200 nm～300 nm were successfully synthesized via pre-emulsion and semi-continuous seeded emulsion polymerization process. The analysis on the surface tension and coagulation rate of polymeric system, size and distribution of latex particles indicated that the composite emulsifier of sodium dodecyl sulfonate/polyoxyethylene nonyl phenyl ether (SDS/OP-10) had the best emulsified effect. The optimal ratio of SDS/OP-10 was 1:1 and its optimum dosage was 1.0% of monomer amount. FTIR analysis results confirmed that ITA participated in the copolymerization reaction and the chemical bond between P(MMA-ITA) copolymer and PBA core existed in the interfacial of core and shell. DSC analysis results showed that the glass transition temperature (T _g) of P(MMA-ITA) copolymer increased with the increase of the ITA dosage and decreased with the increase of the core shell mass ratio. TEM images revealed that CSR particles had core-shell morphology indeed, but the particles’ core-shell morphology would be changed at higher ITA dosage and core shell mass ratio. The size of CSR particles was 330 nm, and the diameter of PBA core was 290 nm. ITA content in the shell of CSR particles was analyzed by non-aqueous acid-base titration. ITA content was the highest at 6% of ITA dosage, ITA amount which chemically bonded with PBA core was the highest at 8% of ITA dosage. When the core shell mass ratio was 60/40, ITA content and ITA amount which grafted onto PBA core were both the highest. ITA content of CSR particles achieved above 1.11% in this work, and it is completely possible for using CSR particles toughening and compatibilizing polyamide 6 (PA 6).     

Polar Gradient Latex Particles with Hydrophilic Core and Hydrophobic Shell Prepared via Multistep Emulsion Polymerization

Monodisperse polar gradient particles were synthesized via a three‐step emulsion polymerization using poly(butyl acrylate‐methyl methacrylate‐methacrylic acid‐ethylene glycol dimethacrylate) (P(BA‐MMA‐MAA‐EGDMA)) as core, poly(methyl methacrylate‐methacrylic acid‐styrene) (P(St‐MMA‐MAA)) as interlayer and polystyrene (PSt) as shell. The particle growth and encapsulation in each emulsion polymerization step were followed by transmission electron microscopy (TEM), dynamic light scattering (DLS) and conductometric titration. Results indicated that the feeding mode and the interlayer were essential to prepare the polar gradient latex particles with hydrophilic core and hydrophobic shell. The morphologies of the two‐layer core/interlayer and three‐layer core/interlayer/shell particles were observed in TEM micrographs, and the sequential encapsulations of the carboxyl‐containing core and the core/interlayer particles were confirmed by an increase in the particle size as well as an increase in the buried carboxyl percentage.     

亚微米级聚苯乙烯/聚硅氧烷核壳粒子的制备及其应用

以乳液聚合制备的聚苯乙烯乳液为种子,加入甲基三甲氧基硅烷(MTMS)水解溶液进行缩聚反应,合成亚微米级聚苯乙烯/聚硅氧烷核壳粒子,并以此作为光散射剂添加至聚甲基丙烯酸甲酯(PMMA)树脂中,制备了光散射材料;考察了亚微米级核壳粒子添加在PMMA树脂中的分散性。结果表明:经过双螺杆剪切作用的挤出加工后,可以实现核壳粒子在PMMA树脂中的良好分散。核壳粒子可以大幅度提高PMMA的雾度,当聚苯乙烯/聚硅氧烷核壳粒子(NS82)的含量为1%时,制得的PMMA样片(厚度为2 mm)的雾度为89%,透光率为69%,有效光散射系数为61%。     

Effect of Monomer Feeding Mode on thePreparation of Hollow Latexes with High MAA Content in the Core Latex Preparation简

In order to prepare hollow latex particles with optimum morphology based on osmotic swelling principle, three- layer core/shell latex particles with 40 wt% MAA in the core were first prepared via multistep seeded emulsion copolymerization, in which monomers were added by a semi-continuous process with monomer addition under two different forms： pure monomers＇ mixture （monomer addition）, and pre-emulsified monomers （pre-emulsion addition）. Then, the hollow latex particles with different morphologies were obtained after alkali post-treatment. Influences of the monomer feeding mode on the emulsion polymerization and the particle morphology were investigated. Results showed that the pre- emulsion addition could significantly improve the polymerization stability in each step, and greatly enhance the uniformity of shell encapsulation. The sizes of the core and core/shell latex particles obtained by the pre-emulsion addition were smaller and more uniform than those synthesized by the monomer addition, and the hollow latex particles with intact morphology were generated by alkali post-treating of the core/shell latexes prepared from the pre-emulsion addition. As the core size increased, the morphology of the post-treated particles underwent evolution from hollow to collapse. Moreover, the mechanism of the particle morphological evolution was proposed.     

Effect of the Shell Crosslinking Level andCore/Shell Ratio on the Morphology of LatexParticles in the Preparation of Hollow Latexes简

Three-layer core/shell latex particles with various shell crosslinking level and shell thickness were prepared by multistep emulsion polymerization, and the hollow latex particles with different morphologies were then obtained after alkali post-treatment. Influences of divinyl benzene(DVB) content and the core/shell mass ratio on emulsion polymerization and particle morphology were investigated. Results showed that with the increase of DVB content, the percentage of total amount of ―COOH on the particle surface and free in aqueous phase(PSFa) decreased, and the morphology of the post-treated particles underwent evolution from cracked, intact hollow to deficient swelling structure. Decreasing the core/shell mass ratio could not only make more carboxyl groups encapsulated by the shell, but also increase the shell resistance to the swelling of the core. The uniform hollow latex particles with intact morphology were obtained when the DVB content was 3.54 wt% and the core/shell mass ratio was 1/6.     

单分散聚丙烯酸丁酯-二氧化硅核壳粒子的制备

近年来,有机-无机核壳材料因其具有可调的光、电、磁等特性而备受关注．无机物外壳可以增强粒子的热力学稳定性、机械强度和抗拉性能．高分子乳胶粒内核具有弹性,且易成膜,外部包覆无机物的乳胶粒可结合两者特性并产生协同效应．     

VAc/BA核壳乳液聚合乳胶粒形态演化

由两种单体分阶段种子乳液聚合制得的核壳型乳胶粒 ,可能存在着多种多样的形态 .由于不同的形态在使用中具有不同的性能 ,因此 ,核壳型乳胶粒的结构形态的研究一直受到人们的十分重视 .近年来 ,Ｓｕｎｄｂｅｒｇ[1] 等指出 ,正向、反向、两半球、两种孤立粒子等四种形态是热力学平衡形态 ,其他形态则是未达平衡的过渡形态 .并且提出用界面自由能最小的方法判别其中哪一种是最终平衡形态 .显然 ,自不平衡形态到平衡形态需要链迁移 ,Ｃｈｅｎ[2 ] 、Ｊｏｎｓｓｅｎ[3 ] 、Ｇｏｎｚａｌｅｚ[4] 等指出 ,链迁移的阻力是粘性力 .对于聚醋酸乙烯酯…     

Preparation and Characterization of Polymer Core Shell Latex Particles

Stable core‐shell latex was synthesized by semicontinuous seeded emulsion polymerization with core monomers consisting of styrene (St), butyl acrylate (BA), and shell monomers consisting of methyl methacrylate (MMA), eutyl acrylate (EA), and methacrylic acid (MAA). The effects of compound emulsifier amount, mass ratio of anionic/nonionic emulsifier, and initiator amount on latex performance were investigated. By particle size analysis and transmission electron microscopy (TEM) observation, results suggest that final latex particles have clearly core shell structures.