大港常压渣油临氮与临氢热反应过程中胶体稳定性变化研究

对比了大港常压渣油临氮和临氢热反应过程中的胶体稳定性变化。结果表明,随着反应时间的延长,在热反应生焦诱导期内,渣油样品的胶体稳定性迅速下降;开始生焦后,胶体稳定性缓慢下降。从组分组成和组分性质角度,对大港常压渣油样品在热反应过程中胶体稳定性变化原因进行了分析。结果表明,随着反应时间的延长,沥青质含量先上升、后下降,在生焦诱导期结束时达到最大值,与体系胶体稳定性的变化特征相一致。随着热反应的进行,饱和分和轻芳烃组分的含量在上升,重芳烃、轻胶质、中胶质、重胶质含量下降,临氮热反应过程中轻胶质、中胶质、重胶质含量的下降更为显著。对渣油样品各组分的数均相对分子质量和平均偶极矩进行了研究。结果表明,随着热反应的进行,轻、中、重胶质组分的数均相对分子质量和平均偶极矩呈下降趋势,而沥青质的数均相对分子质量和偶极矩先增大后减小,从而使沥青质和胶质的分子性质差别先增加后减小,与体系胶体稳定性的变化趋势一致;同时沥青质的偶极矩变化表明,强极性的沥青质优先聚集生焦、临氢热反应过程中,氢与催化剂的作用有助于抑制沥青质分子量增大和极性增强,从而有助于抑制生焦。     

桐油预聚物改性沥青

将桐油用无水AlCl3引发聚合为低分子预聚物,预聚物再与沥青继续进行聚合反应以对其改性。改性后的沥青针入指数和低温延度均有改善。用红外、特性粘接[η]及薄层色谱方法对预聚反应、聚合度及改性沥青进行了分析。发现预聚物主要与沥青中的胶质、沥青质发生了反应。反应物可以作为界面剂增加沥青中其它组分的相容性。在沥青质上加成桐油预聚物后,可以克服其刚性强、互容性差的缺点,对稳定沥青的胶体结构、改善沥青的针入指数、低温延度有较好作用。桐油预聚体在沥青混合物中的质量分数为3％－6％时沥青可具有较好的性能改善结果。     

质量分率电导率法研究几种不同渣油的胶体稳定性

测定了中东常压渣油、中东减压渣油、大庆减压渣油和中东减压渣油正庚烷可溶质在用正庚烷稀释过程中的电导率，并计算得到了不同正庚烷稀释比例时的质量分率电导率，将质量分率电导率出现最大值时的（正庚烷/渣油）比值定义为渣油胶体稳定参数。用该方法研究不同渣油的胶体稳定性，对以上几种油品的研究结果与各油品的饱和分、芳香分、胶质、沥青质组分（SARA）组成所能反映的体系的稳定性是相一致的。     

石油组分及其模型化合物的超分子化学作用

原油是最复杂的化学体系之一,人们对原油这种复杂的胶态分散体及其稳定性的研究兴趣与日俱增,尤其是与石油稳定性密切相关的沥青质超分子聚集体。但人们对形成沥青质超分子聚集体的主要作用力长期以来颇有争议。本文重点介绍了石油组分及其模型化合物在溶液中形成超分子聚集体的超分子化学作用研究进展。通过实验方法和理论计算证明沥青质聚集体是沥青质分子间通过氢键、π-π堆积、偶极-偶极相互作用等多种分子间弱相互作用力协同作用形成的热力学稳定结构;合成具有沥青质结构特点的纯化合物,研究它们在溶液中的行为,是提高对沥青质在液态相中自缔合行为认识的有效方法;结合现阶段的研究状况,对石油组分模型化合物的超分子化学作用研究的发展前景进行了展望。     

煤沥青橡胶改质筑路油老化过程中族组成与性质变化

实验室与户外跟踪老化研究发现 ,道路沥青在使用过程中的质量蜕变主要是由于氧化作用[1,2 ]使得道路沥青中沥青质含量增加 ,改变了沥青中分散相与连续相的比例 ,致使沥青的性质发生变化 ,如软化点升高、针入度降低以及粘度增加等[3,4]。上述研究所取得的成果主要是以石油为原料的道路沥青 ,对以煤沥青为原料开发的改质筑路油研究较少。本文在成功开发煤沥青改质筑路油工艺的基础上 ,研究了改质筑路油热老化过程中族组成与性质的变化 ,由此提出煤沥青改质筑路油高温热老化过程中性质变化的主要原因。1　实验部分1 1　原料　试验所用原料为实…     

中东常压渣油热反应样品Zeta电位的研究

长期以来,有诸多研究者认识到了渣油的胶体性质,并且利用各种实验手段对其进行了研究。渣油的胶体稳定性对其热反应性能有重要影响作用。前人的研究认为,渣油胶体体系中的分散相主要是由沥青质构成,分散介质由芳香分和饱和分共同构成,吸附层由胶质构成。胶体的一个重要性质是电性质,渣油分子中含有大量的杂原子,使渣油极性分子的存在和渣油胶粒具有一定的电性。     

格尔木渣油加氢反应及生焦行为的研究

选用超低沥青质含量的格尔木渣油（沥青质质量分数：0.32%）作为加氢原料,考察反应条件对加氢反应样品组分性质、胶体稳定性参数（CSP）、生焦性能的影响。结果表明,随着加氢反应温度的升高和反应时间的延长,沥青质和饱和分的含量增加,胶质和芳香分的含量减少;胶体稳定性参数降低,生焦率不断增加;胶质与沥青质的缩合度增加,芳碳率f_A不断增大;金属与杂原子在加氢过程中不断得到脱除,V比Ni更容易脱除、S比N更容易脱除;催化剂表面形成了类似石墨有序结构的炭基物质,使得催化剂的孔结构参数不断减小。在所研究的反应中,当反应温度和时间分别为420℃和5 h时,催化剂的孔结构损害最为严重,出现了较大的微孔分布。     

固体粒子稳定的乳状液研究进展

综述了固体粒子对乳状液稳定性影响的有关研究进展。微细不溶的固体粒子构成重要的一类乳化剂,被水相和油相部分润湿的固体粒子能够有效地稳定乳状液。固体粒子稳定乳状液的效果取决于以下因素:粒子大小、粒子间相互作用和粒子的润湿性质。固体粒子存在的油-水界面表现出粘弹行为,这种粘弹界面膜可大大地提高空间位阻,减缓乳状液液珠间液膜变薄的速率,从而提高乳状液地稳定性。原油中的粘土、胶质、沥青质和石蜡等胶体粒子被证明对乳状液的稳定性起很大的作用。     

热改质过程中渣油结构及其重组分溶剂化变化规律研究

以委内瑞拉减压渣油为原料,采用微型反应釜,研究了其在410℃、2.0 MPa氮气初压下,不同反应停留时间的热改质过程生成油的化学结构组成及其重组分溶剂化变化规律。通过1H-NM R技术研究了热改质过程生成油中沥青质和重胶质不同化学位移归属氢的转化路径;并结合改进的Brown-Ladner法分析了热改质过程生成油中沥青质和重胶质的平均分子结构参数变化;采用蒸汽压渗透法考察了热改质过程生成油中沥青质和重胶质在甲苯溶液中所形成的复合超分子结构的平均相对分子质量。结果表明,随着热改质程度的加深,沥青质和重胶质的H/C原子比减小,供氢能力逐渐下降,沥青质和重胶质的芳香环共轭程度和fA在体系生焦后(45 min)显著提高;沥青质的聚集趋势相关值在热改质15 min前变化不大,15 min后显著增强,而重胶质在整个热改质过程中,其聚集趋势相关值的增势较为缓和;沥青质和重胶质的聚集趋势相关值差异逐渐增大,15 min时增加了1.5%、25 min时增加了50.8%、45 min时增加了142.3%,表明沥青质和重胶质的结构差异越来越明显;重胶质溶剂化沥青质的能力逐步减弱,体系的溶剂化参数从0时的32.9%逐步降到15 min时的29.5%、25 min时的14.1%和45 min时的9.6%;热改质生成油的斑点实验等级逐渐增加,体系的胶体稳定性逐渐降低。     

渣油中沥青质胶粒缔合状况初探

目前一般认为[1] ,石油中的沥青质的基本结构是以多个芳香环组成的稠合芳香环系为核心 ,周围连接有若干的环烷环 ,芳香环和环烷环上都还带有若干个长度不一的正构烷基侧链 ,其中还杂有各种含硫、氮、氧的基团 ,同时还会络合钒、铁等金属。这种以一个稠合的芳香环系为核心的结构是组成胶质或沥青质的基本单元。大量研究表明 ,沥青质由若干个这类单元结构组成 ,以缔合状态存在 ,渣油及其沥青质的分子量都随测定所用溶剂的极性不同而变化 ,在弱极性有机溶剂中所测得的分子量较大 ,在强极性的有机溶剂中所测得的分子量偏小。初步研究表明 ,沥青…     

In Defense of Vapor Pressure Osmometry for Measuring Molecular Weight

The value of the average molecular weight of petroleum asphaltenes continues to be controversial. Usually the disagreement is about the measurement of a single asphaltene fraction when the need is for a consistent picture that comprises all fractions of petroleum and includes chemical changes during processing. By using one of the better solvents for carbonaceous materials, o‐dichlorobenzene, at the maximum instrument temperature, vapor pressure osmometry provides a consistent measurement of number average molecular weight not achieved by any other technique. This average molecular weight is consistent among petroleum fractions and gives predictable changes in asphaltene molecular weight with thermal processing.     

Study of a supramolecular structure of continental type petroleum asphaltenes

Supramolecular, electronic, and chemical structures of petroleum asphaltene molecules are studied. The investigations are carried out by quantum chemistry and molecular mechanics methods. The quantum chemical calculation of the structure-chemical parameters of dimers and trimers of petroleum asphaltenes is made using DFT/B3LYP. The refined values of the ionization potential and electron affinity of petroleum asphaltene molecules, their dimers and trimers agree well with the electron spectroscopy data. The results of the study of geometric structures of petroleum asphaltene dimers and trimers confirm the non-planar structure of asphaltenes.     

Polarization of Fluorescence of Asphaltene Containing Systems

Formation of supermolecular structures in petroleum disperse systems is determined by interactions of asphaltenes. Petroleum systems are lyophilic oleocolloids with low polar dispersive media which is in dynamic balance with elements of disperse structure. Supermolecular scale of organization is most important for determining the macroscopic parameters. Levshin-Perrin equation for depolarization of fluorescence was modified for polydispersed systems. Interfacial tension coefficient of model asphaltene solution was calculated in a case of Volmer's function. For technogenic mixtures the temperature dependences of the sizes near the point of phase transition are presented. Enthalpy of asphaltene association per one molecule was calculated. Polarization degree together with macroscopic parameters correlates with appearance of asphaltene dispersed phase in system.     

Single molecule force spectroscopy of asphaltene aggregates

Asphaltene aggregation and deposition cause severe problems in nearly all phases of petroleum processing. To resolve those problems, understanding the aggregation mechanisms is a prerequisite and has attracted the interest of a great number of investigators. However, to date, the nature and extent of asphaltene aggregation remain widely debated. In the present study, we attempt to investigate asphaltene aggregation from a completely new perspective. The technique of single molecule force spectroscopy (SMFS) was used to investigate the response of single asphaltene aggregates under an external pulling force. Force curves representing the stretching of single asphaltene aggregates were obtained in simple electrolyte solutions (KCl and calcium) and organic solvents (toluene and heptane). These force curves were well-fitted by the modified worm-like chain model, indicating that those asphaltene aggregates acted like long-chain polymers under pulling by an external force. It was found that lower solution pH values and the presence of divalent cations resulted in a lower bending rigidity of the formed aggregates. The information retrieved from the force curves suggests that asphaltene molecules with a structure featuring small aromatic clusters connected by aliphatic chains do exist and that asphaltene aggregation could occur through a linear polymerization mechanism. The current study extends the application scope of SMFS.     

Asphaltene precipitation modeling through ACE reaping of scaling equations

Precipitation and deposition of asphaltene have undesirable effects on the petroleum industry by increasing operational costs due to reduction of well productivity as well as catalyst poisoning.Herein we propose a reliable model for quantitative estimation of asphaltene precipitation.Scaling equation is the most powerful and popular model for accurate prediction of asphaltene precipitated out of solution in crudes without regard to complex nature of asphaltene.We employed a new mathematical-based approach known as alternating conditional expectation(ACE)technique for combining results of different scaling models in order to increase the accuracy of final estimation.Outputs of three well-known scaling equations,including Rassamdana(RE),Hu(HU),and Ashoori(AS),are input to ACE and the final output is produced through a nonlinear combination of scaling equations.The proposed methodology is capable of significantly increasing the precision of final estimation via a divide-andconquer principle in which ACE functions as the combiner.Results indicate the superiority of the proposed method compared with other individual scaling equation models.     

Determination of the Onset of Asphaltene Precipitation by Visible Ultraviolet Spectrometry and Spectrofluorimetry

Abstract

Asphaltene deposition is a problem for the petroleum industry, affecting the production, transport, and storage of crude oil. The aim of this work is to develop and compare different methods to determine asphaltene precipitation. Two asphaltene fractions, one extracted from a Brazilian crude oil sample and the other from petroleum distillation residue, were evaluated by using model systems constituted of toluene/n-heptane in different compositions, using visible ultraviolet spectrometry and spectrofluorimetry. The results of the precipitation tests carried out by these two methods agreed, indicating they are effective to analyze asphaltene deposition and the performance of chemicals as asphaltene stabilizers.     

煤焦油重组分沥青质性质分析及对加氢裂化生焦影响的推测

从中/低温煤焦油中切取重组分,提取了重组分C7-沥青质,并以此重组分为原料进行了高压釜加氢实验,通过1H-NMR、XRD、FT-IR、SEM、元素分析和相对分子量测定等手段对重组分沥青质结构参数、官能团、表观形态等方面进行了分析,并将其与加氢过程中生焦情况进行了关联。结果表明,C7-沥青质基本结构单元以稠环芳烃为中心,周围分布少而短的侧链,侧链以小于3个碳的短直链正构烷基为主,相对分子量小,芳香片层没有堆积结构。O是该沥青质中氢键主要来源,大多分布在环氧烷烃和醚类结构中,外围的O数量低,分子间氢键更难形成,结构单元之间缔合性弱,沉积聚合慢而均匀。沥青质中短侧链不易断裂,在反应过程中产生的稠环芳烃自由基少,缩合能力小,使该馏分油生焦能力低,具有较高的加氢潜质。     

石油沥青质的NMR测定及其模型分子推测

从6种不同原油中分离提取了正己烷不溶的沥青质，测定了沥青质的1H NMR(Nuclear Magnetic Resonance)和13C NMR谱，从不同类型氢和碳原子的质量分数计算得到了一系列平均结构参数，结合相对分子质量测定和元素分析，给出了沥青质基本结构单元的平均分子式，推测了模型分子的结构。结果表明，沥青质的基本结构单元可以用稠环芳烃连接环烷烃和烷基侧链并含氧、氮和硫等杂原子的单元表示，结构单元之间形成缔合体，缔合数为4～6。     

Colloidal interactions between asphaltene surfaces in aqueous solutions

Asphaltene at oil/water interfaces plays a dominant role in the recovery of crude oil. In this study, asphaltene monolayer films were deposited on hydrophobic silicon wafers and silica spheres from oil-water interfaces using a Langmuir interfacial trough. The morphology of the deposited asphaltene films was characterized with an atomic force microscope (AFM). The colloidal forces between the prepared asphaltene films in aqueous solutions were measured with AFM to shed light on the stabilization of water or oil droplets coated with asphaltene films. Factors such as solution pH, KCl concentration, calcium addition, and temperature all showed a strong impact on colloidal forces between the prepared asphaltene films. The findings provided a better understanding of asphaltene interfacial films at an oil/water interface in stabilizing bitumen-in-water and water-in-bitumen emulsions.     

沥青质分散剂对沥青质的稳定及缔合的影响

采用紫外－可见光谱法研究了沥青质分散剂对甲苯－正庚烷－沥青质体系中沥青质的稳定作用,通过黏度法考察了沥青质分散剂对沥青质溶液中胶束缔合度的影响。结果表明,十二醇（DAL）、十二烷基苯磺酸（DBSA）、十二烷基苯酚（DP）对沥青质都有一定的稳定作用。三种沥青质分散剂的稳定作用顺序为DBSA>DP>DAL。DAL、DP及DBSA浓度较低时（1%）对沥青质甲苯溶液黏度的影响规律相似,推迟了黏度迅速增加的拐点,即可以抑制沥青质胶束的缔合。DBSA浓度较大时,沥青质胶束没有明显的聚并,同时使得沥青质溶液的相对黏度增加明显。三种沥青质分散剂都能显著降低胶束的聚集数;三种沥青质分散剂抑制沥青质胶团聚并强弱顺序为：DBSA>DP>DAL。这与其头部官能团的酸性顺序一致。