加速溶剂萃取-气相色谱法检测土壤中14种有机氯农药方法

建立了加速溶剂萃取-气相色谱检测土壤中14种有机氯农药(OCPs)的方法。对影响OCPs回收率的主要因素进行优化,得出优化条件:1次静态萃取循环,萃取温度90℃,静态萃取时间3 min,冲洗量30%,氮气吹扫时间40 s,正己烷/丙酮(1∶1,V/V)为萃取液。在优化条件下,加标水平为10、100?g/L时,平均加标回收率为86.6%～120%、88.1%～120%,相对标准偏差(n=7)均小于10%,方法检出限(t值法)为1.03～2.64?g/L。     

加速溶剂萃取-固相萃取净化-气质联用法测定稻谷中18种农药残留

建立了加速溶剂萃取-固相萃取净化-气质联用法(ASE/SPE/GC-MS)测定稻谷中18种农药残留的方法.以乙腈为溶剂,样品经加速溶剂萃取(30 m L萃取池中,10.34 MPa压力、80℃条件下,加热5 min,用乙腈静态萃取3 min,循环2次,再用池体积60%的乙腈冲洗萃取池后用氮气吹扫100 s)后,过自制固相萃取柱净化(萃取速率:1滴/秒),洗脱旋蒸后正己烷定容,使用气相色谱-质谱联用仪分析.在优化条件下,18种农药在0.05~1.0μg/m L质量浓度范围内的相关系数R2均大于0.99,浓度与峰面积之间呈良好的线性关系.分别以3倍标准偏差和8倍标准偏差计算检出限和定量限,18种农药的检出限为0.104~0.647 mg/kg,定量限为0.276~1.724 mg/kg.以空白样品为基体进行加标回收试验,平均回收率在82.5%~105.1%之间,相对标准偏差(RSD,n=6)为1.5%~6.4%.方法适用于稻谷中18种农药残留的检测.     

气相色谱-质谱法分析烟草中有机磷农药残留量及其烟支转移率研究

建立了一种用加速溶剂萃取,自动固相萃取净化,气相色谱/质谱联用检测烟草中29种有机磷农药残留量的方法.考察了加速溶剂萃取仪的萃取温度、溶剂、加热时间和循环次数对回收率的影响,对固相萃取的洗脱溶液及其体积和流速进行了优化,利用保留时间和定性离子定性,以灭蚁灵为内标进行定量,29种有机磷农药的平均回收率在61.4%～128%之间,相对标准偏差在12%以下,符合烟草中农药多残留检测的要求.通过对烟支进行加标,探讨了有机磷农药向主流烟气和烟蒂的转移情况,其向主流烟气的平均转移率为小于6.3%,相对标准偏差为8.0%～18.5%,而烟蒂平均截留率为0.3%～15.0%,相对标准偏差为6.5%～21.3%,表明有机磷农药有较小的转移,为卷烟安全性评价提供了可靠的数据.     

加速溶剂萃取法提取中药材中黄芪甲苷

采用加速溶剂萃取仪(ASE)以甲醇为溶剂提取黄芪药材中的黄芪甲苷,利用高效液相色谱-蒸发光散射检测器(HPLC-ELSD)进行含量测定.考察了不同的提取温度、提取时间、循环次数等条件下的提取效果,确定了最佳的ASE提取条件.同传统的提取方法相比,ASE法溶剂用量少,耗时短,提取效率高.并通过回收率和精密度的测定,证明加速溶剂萃取技术完全可以用于中药材中的黄芪甲苷的提取.     

加速溶剂萃取-磁固相萃取净化-气相色谱-质谱法测定土壤中16种多环芳烃和23种有机氯残留

建立了加速溶剂萃取（ASE）、磁固相萃取净化（MSPE）、气相色谱-质谱（GC-MS）测定土壤中多环芳烃和有机氯残留的方法。ASE萃取溶剂为丙酮-正己烷（1：1，v/v），萃取温度为100℃，萃取压力为11.032 MPa，加热时间为5 min，静态萃取时间为5 min，循环萃取3次，冲洗体积为60%萃取池体积，氮气吹扫100 s。然后采用室温制备法自制ZIF-8/nZVI磁性材料用于净化萃取液，将净化液浓缩定容后进行GC-MS测定。多环芳烃和有机氯的线性范围为5~200 μg/kg，线性相关系数（r²）均大于0.99；目标物的检出限（LOD，S/N=3）为0.04~1.21 μg/kg。所建方法成功用于土壤样品中16种多环芳烃和23种有机氯的测定，在3个加标水平下得到的加标回收率为63.9%~112.1%，相对标准偏差（RSD）为0.4%~26.2%。研究结果表明，该方法具有灵敏度高、重现性好、回收率高等特点，适用于土壤中多环芳烃和有机氯残留的检测。     

烟草中有机氯类农药多残留分析前处理方法对比研究

以烟草中有机氯类农药为研究对象,从检出限、回收率、重复性和色谱图4个方面系统比较了机械振荡萃取法、超声波溶剂萃取法、微波辅助萃取法和加速溶剂萃取法4种常用前处理方法。由于加速溶剂萃取法是在高温高压下进行萃取,在提取出残留农药的同时,也提取出更多的干扰物。机械振荡法、超声波溶剂萃取法和微波辅助萃取法各项结果差别较小,其中机械振荡萃取法回收率和重复性最好,但提取时间较长。考虑溶剂消耗和提取时间等方面的因素,微波辅助萃取是较理想的样品前处理方法。     

加速溶剂萃取法提取海洋沉积物中正构烷烃的方法研究

采用加速溶剂萃取法(ASE)提取了海洋沉积物中的正构烷烃,并对ASE的萃取剂比例、萃取温度、静态萃取时间以及循环次数等实验条件进行优化。结果表明,当样品长碳链正构烷烃含量较高或需要检测长碳链正构烷烃含量时,可使用甲醇-二氯甲烷(1∶3)作为萃取剂;而甲醇-二氯甲烷(1∶9)适用于短碳链正构烷烃含量较高或需要检测短碳链正构烷烃含量的样品。加速溶剂萃取提取沉积物中正构烷烃的最佳条件为:萃取温度150℃,静态提取时间15 min,循环3次。在优化条件下,测定沉积物样品中正构烷烃的精密度除C15为20%外,其余为3%~14%,替代物回收率为84%~114%。相比于传统的索氏提取法,该方法的工作效率高、回收率高、精密度良好,适用于沉积物样品中正构烷烃的定量分析。     

加压溶剂萃取-气相色谱法测定荞麦中残留的有机氯农药

用所研制的24位全自动加压溶剂萃取仪(APLE),以丙酮-正己烷(体积比为1∶1)为溶剂,在100 ℃和10 MPa条件下,对荞麦样品中残留的7种有机氯农药进行了萃取,并通过气相色谱对萃取液进行定量分析。萃取的绝对回收率为68%～126%,相对标准偏差为1.2% ～14.7%,检测下限为0.051～0.18 ng/g。与索氏提取法对比,相对提取回收率为116%～148%,表明萃取收率高于索氏提取法。     

加速溶剂萃取-固相萃取净化-气相色谱-串联质谱法检测茶叶中9种拟除虫菊酯类农药残留

建立了加速溶剂萃取（ASE）-固相萃取净化（SPE）-气相色谱-串联质谱（GC-MS/MS）同时测定茶叶中9种拟除虫菊酯类农药残留的方法。ASE萃取溶剂为丙酮-正己烷（1：1,v/v）,萃取温度为100℃,萃取压力为10 MPa,加热时间为3 min,静态萃取时间为5 min,循环1次,冲洗体积为40%萃取池体积,氮气吹扫100 s。萃取结束后用Cleanert TPT固相萃取柱净化,净化液浓缩定容后,采用GC-MS/MS测定,外标法定量。9种拟除虫菊酯类农药在2~1000 μg/L范围内呈现良好的线性关系,相关系数（r²）均大于0.99,方法检出限为0.2~4.5 μg/kg,定量限为0.8~15.0 μg/kg。在绿茶、红茶空白基质中做加标回收试验,添加水平为0.02、0.1、0.4 mg/kg以及定量限水平,得到的平均回收率为69.87%~110.0%,相对标准偏差（RSD）为0.7%~11.2%。该方法背景干扰低、灵敏度高、重现性好、回收率稳定,适用于茶叶中拟除虫菊酯类农药残留量的检测。     

加速溶剂萃取-丙基化衍生-气相色谱质谱法测定土壤中的三甲基铅与三乙基铅

建立了加速溶剂萃取-丙基化衍生-气相色谱质谱联用分析土壤中的三甲基铅与三乙基铅的方法。不加任何填充物,温度为100℃,静态萃取时间5 min,循环次数为2次,冲洗体积为65%,吹扫时间90 s时得到最大的回收率;在此条件下,三甲基铅与三乙基铅的的回收率分别为92. 12%,90. 54%。三甲基铅与三乙基铅在0. 05～20 mg/L的范围内,具有良好的线性关系(r~2≥0. 999),其方法检出限分别为0. 02 mg/kg及0. 025 mg/kg。将该方法应用于真实样品的检测,样品加标回收率可达90%以上,相对标准偏差(RSD)小于6%。适用于土壤中三甲基铅与三乙基铅的分析。     

A methodology for choosing parameters for ESR readout of alanine dosimeters for radiotherapy

Spectrometer settings for ESR readout of alanine dosimeters for radiotherapy have been investigated. Several ESR parameters were studied and determined. The main reason for this work is to choose the suitable parameters to increase signal-to-noise ratio and to reduce the uncertainty on ESR readout, which is one of the main components of uncertainty of alanine/ESR dosimetry system for radiotherapy. The new spectrometer settings have been applied for ESR readout of alanine dosimeters irradiated from 1 to 10 Gy. A higher signal-to-noise ratio has been achieved compared to our old spectrometer settings. The extended uncertainty (k=2) has been evaluated in the dose range 2–10 Gy (maximum uncertainty of 4.9% for 2 Gy, while minimum uncertainty of 1.4% for 10 Gy), which implies that the alanine/ESR dosimetry system can be applied to radiotherapy dose level that needs a global accuracy of 5%.     

Prospects for development of a technology for production of butene-1

Industrial technologies for production of butene-1 are described, including the most promising process for recovery of butene-1 of polymerization purity from C₄ fractions formed in pyrolysis and catalytic cracking of hydrocarbons. It is shown that this technology can be improved and suggested to use as a raw material the recycle butene fraction formed from these C₄ fractions upon isolation of 1,3-butadiene and isobutene. A technological scheme for recovery of butene-1 of polymerization purity is suggested.     

Preparation of PVA membrane for immobilization of GOD for glucose biosensor

A membrane was prepared using polyvinyl alcohol (PVA) with low and high degree of polymerization (DOP), acetone, benzoic acid (BA) and was cross-linked by UV treatment. Membrane composition was optimized on the basis of swelling index. Membrane prepared with 12% low DOP and 8% high DOP of PVA, 2% BA, dissolved in buffer containing 20% acetone and cross-linked with UV treatment exhibited lower swelling index. Fourier transform infrared (FTIR) study of the membranes showed appearance of a strong band at approximately 2337 cm(-1) when UV was used for cross-linking in the presence of benzoic acid. Scanning electron microscope (SEM) study revealed that membrane cross-linked with UV treatment was smoother. Glucose oxidase (GOD)-PVA membrane was associated with the dissolved oxygen (DO) probe for biosensor reading. Glucose was detected on the basis of depletion of oxygen, when immobilized GOD oxidizes glucose to gluconolactone. A wide detection range, 0.9-225 mg/dl was estimated from the linear range of calibration plot of biosensor reading. Membranes were reused for 32 reactions without significant loss of activity and stored for 30 days (approximately 90% activity) at 4 degrees C. Membranes were also used with real blood samples.     

New method for prefractionation of plasma for proteomic analysis

The depth of proteome analysis is severely limited in complex samples with a wide dynamic range of protein abundance such as plasma. Removal of high‐abundance proteins should reveal the signal of lower abundance plasma proteins. However, smaller proteins may be part of larger protein complexes and hence the removal of proteins involved in complexes with high‐abundance proteins such as albumin may inhibit the search for disease biomarkers. Prefractionation of a sample divides it into fractions of reduced complexity, allowing improved detection of lower abundance proteins. Using a prefractionation device, which employs Gradiflow? technology, we were able to separate small volume plasma samples into multiple fractions based on the molecular weight and/or charge. The resulting samples of reduced complexity were directly compatible with 2‐DE. The use of this prefractionation machine may therefore be useful in the hunt for disease biomarkers.     

Application of thermal analysis for investigations of polymer powders for coatings

Polypropylene coatings obtained by the fluidized bed method were investigated. It was proved that the application of thermal analysis methods for their characterization gave many useful data, as a consequence of the similar conditions of thermal measurements and plastics powder processing. Significant correlations were found between the thermal properties and the standard coating poperties.

---

Zusammenfassung Durch Fluidisationsverfahren erhaltene Polypropylenbeschichtungen wurden untersucht. Es wurde festgestellt, daß infolge der ähnlichen Bedingungen von thermischen Messungen und Plastpulverisierungsverfahren die Anwendung von thermischen Untersuchungsmethoden zu deren Charakterisierung viele nützliche Angaben liefern. Es konnten eindeutige Beziehungen zwischen thermischen Eigenschaften und Standardbeschichtigungseigenschaften gefunden werden.

---

, . , , . .

     

Potential of FTIR spectroscopy for analysis of tears for diagnosis purposes

It has been widely reported that the tear film, which is crucially important as a protective barrier of the eye, undergoes biochemical changes as a result of a wide range of ocular pathology. This tends to suggest the possibility of early detection of ocular diseases on the basis of biochemical analysis of tears. However, studies of tears by conventional methods of biomolecular and biochemical analysis are often limited by methodological difficulties. Moreover, such analysis could not be applied in the clinic, where structural and morphological analyses by, mainly, slit-lamp biomicroscopy remains the recommended method. In this study, we assessed, for the first time, the potential of FTIR spectroscopy combined with advanced chemometric processing of spectral data for analysis of raw tears for diagnosis purposes. We first optimized sampling and spectral acquisition (tears collection method, tear sample volume, and preservation of the samples) for accurate spectral measurement. On the basis of the results, we focused our study on the possibility of discriminating tears from normal individuals from those of patients with different ocular pathologies, and showed that the most discriminating spectral range is that corresponding to variations of CH₂ and CH₃ of lipid aliphatic chains. We also report more subtle discrimination of tears from patients with keratoconus and those from patients with non-specific inflammatory ocular diseases, on the basis of variations in spectral ranges attributed notably to lipid and carbohydrate vibrations. Finally, we also succeeded in distinguishing tears from patients with early-stage and late-stage keratoconus on the basis of spectral features attributed to protein structure. Therefore, this study strongly suggests that FTIR spectral analysis of tears could be developed as a valuable and cost-saving tool for biochemical-based detection of ocular diseases, potentially before the appearance of the first morphological signs of diseases. Combined with supervised modelling methods and with use of a spectral data base acquired for representative patients, such a spectral approach could be a useful addition to current methods of clinical analysis for improvement of patient care.

Adhesives for assembly procedures for products of radioelectronic industry

A list of adhesive materials, sealants, and potting compounds used at the enterprise is given. The basic properties of these materials are discussed, and particular process procedures in which they are employed are described.     

Piperazine-based buffers for liposome coating of capillaries for electrophoresis

Anionic liposomes can be coated on fused-silica capillaries for electrophoresis in the presence of N-(hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) (HEPES) as background electrolyte (BGE) solution. In this work, the interaction of various compounds with zwitterionic and anionic phospholipid coatings was studied with HEPES at pH 7.4 as BGE solution. The chromatographic and electrophoretic behavior of three test sample solutions (anionic, cationic, and neutral) was investigated for evaluation of the phospholipid coatings. Our results show that hydrophobic interactions between analytes and the phospholipid coating are important for the migration of charged analytes. In addition, the performances of other piperazine-based buffers, i.e., N-(2-hydroxyethyl)piperazine-N'-(2-hydroxypropanesulfonic acid), piperazine-N,N'-bis(2-ethanesulfonic acid), and piperazine-N,N'-bis(hydroxypropane sulfonic acid), at pH 7.4, as liposome solvent and BGE solution were evaluated and compared with the performance of HEPES at pH 7.4. The anionic liposome solution comprised 80/20 mol% phosphatidylcholine/phosphatidylserine. A simple test solution was selected and the chromatographic and electrophoretic migration behavior of the analytes was evaluated. The results show that, in addition to HEPES, other piperazine-based buffers at pH 7.4 are suitable for coating of fused-silica capillaries with anionic liposomes.     

Prospects for the use of fluidized-bed devices for production of coatings

It is shown that, currently, the most effective grinding and dispersant equipment in the technology of coating production are fluidized-bed devices—devices in which grinding and dispersion of pigments and fillers occur via ferromagnetic bodies driven by an electromagnetic field.     

缓冲溶液pH计算公式的推导

酸碱缓冲溶液在分析化学中的应用是多方面的 ,因此酸碱缓冲溶液 ｐＨ的计算是分析化学中必不可少的一个内容。目前 ,高师院校的分析化学多采用华中师范大学等校编的《分析化学》(第 2版 ) ,笔者在几年的教学中 ,发现该教材在缓冲溶液 ｐＨ计算的公式推导中存在疏漏。为此 ,在比较其他教材中该章节的内容后 ,从酸碱平衡最本质的内容ＰＢＥ出发 ,提出一种新的缓冲溶液ｐＨ计算公式推导方法。1　华中师范大学版教材中的问题[1]　　以一元弱酸及其共轭碱体系进行讨论 ,设弱酸ＨＡ浓度为ｃａ,共轭碱ＮａＡ浓度为ｃｂ。将ＨＡ Ａ-体系以Ｈ2 Ｏ作媒…