共聚物在聚合物共混体系中的增容作用Ⅱ.接枝共聚物和无规共聚物

在不相容的聚合物共混体系中加入共聚物作为增容剂可以有效地改善两相间的界面状况，得到力学性能优良的合金材料。本文主要讨论接枝共聚物和无规共聚物在聚合物共混体系中的增容作用和增容机理。     

几种典型固体聚合物体系的~（13）C自旋－晶格弛豫特性

用固体高分辨ＮＭＲ系统地研究了几种典型的均聚物，共聚物，聚合物共混物以及用接枝共聚物增容的不相容聚合物共混体系的１３Ｃ自旋－晶格弛豫特性。研究结果表明：１３Ｃ自旋－晶格弛豫时间（Ｔ１（Ｃ））是表征固体聚合物体系的很有用参数，它能提供有关本体聚合物微观形态结构的信息，并可望建立聚合物的微观结构与宏观性能的关系，它不仅能准确无误地反映共混体系中可能存在的各种相互作用，而且能定性地给出相互作用的大小和准确地指明相互作用产生的位置，因而为揭示共混体系的相容机理提供了最直接的证据，另外Ｔ１（Ｃ）还能给出增容剂对不相容共混体系的增容作用和增容机制的直接实验证据     

HIPS-g-GMA相容剂对PC/HIPS共混物相容性的影响*

将两种或两种以上聚合物进行共混是获得性能优异合金材料的简单而有效的途径[1,2 ] .但是大多数聚合物共混时 ,由于混合焓ΔＨ >0且混合熵ΔＳ非常小 ,导致混合自由能大于零 ,故大多数共混体系是不相容的 .而对于不相容的共混 ,由于两相间的界面张力大 ,两相间形成锐形界面 ,两相之间的界面粘结力低 ,导致材料性能很差 .为了改善两相间的相容性 ,需要加入相容剂[3 ,4 ] .绝大多数增容剂是嵌段或接枝共聚物 .这类增容剂分子量较大 ,在加工条件下 ,由于其粘度较大往往难于迁移到两相的界面处 ,起不到应有的增容作用 .聚合物反应加工技术是近 2…     

相形态对聚合物反应共混过程的影响

通过采用典型的热力学不相容共混体系聚烯烃弹性体/聚苯乙烯(POE/PS),利用流变学和形态研究的方法,考察了不同相形态(海岛结构和双连续结构)对聚合物反应共混过程的影响.研究发现相形态对聚合物原位增容共混反应有显著的影响,界面反应的进程与界面形态的变化能力直接相关.对于双连续结构的共混物,其形态稳定性最差,因而最有利于界面反应的发生;而在海岛结构的共混体系中,界面反应的进程则取决于界面变形的难易程度,黏度比小的体系更容易发生界面反应。     

共聚物在聚合物共混体系中的增容作用I.嵌段共聚物

随着高分子合金领域的研究发展，以共聚物作为增容剂对不相容的聚合物共混体系进行改性已得到了广泛的研究和应用。本文分为两篇，分别介绍利用嵌段共聚物、接枝共聚物和无规共聚物所做的增容改性研究。本篇着重讨论嵌段共聚物(包括两嵌段和三嵌段以及多嵌段共聚物)在聚合物共混体系中的增容作用和增容机理。     

聚烯烃／极性聚合物界面的分子状态

为了克服高分子共混物界面不易表征的缺点，提出用溶剂选择性溶解方法使界面暴露．结合Ｘ－射线光电子能谱（ＸＰＳ）表征手段，研究了官能化聚合物，接枝型共聚物及带有反应性基团的聚合物作为共混物增容剂时在界面区域的分子状态．实验结果表明，作增容剂时，官能化聚合物在界面区内采取最有利的分子构象，充分发挥增容作用；接枝型共聚物主链、侧链向相应本体聚合物内扩散；而带有反应性基团的聚合物与某个本体聚合物发生反应之前存在反应基团在界面富集的过程     

用于聚合物共混体系的共聚物增容剂

在不相容多相聚合物体系中，共聚物增容剂的存在将对共混物的形态结构及力学性能产生极大的影响，它们的作用是增强相间粘合力，减小相表面张力。本文系统论述了共聚物增容剂的分子设计及其分子特性对增容效果的影响，并分别讨论了反应型及非反应型共聚物增容剂的近期发展。     

PP/PMMA/PP-g-MAH共混物的结晶和相形态研究

采用偏光显微镜和相差显微镜详细研究PP/PMMA不相容聚合物共混物体系和PP/PMMA/PP-g-PMMA增容共混体系的结晶和相形态.偏光显微照片的研究结果表明,增容剂PP-g-MAH中PP结晶需要克服更多的能垒,导致PP结晶形态变得不完善,球晶尺寸变小.比较PP/PMMA和PP/PMMA/PP-g-MAH的相差显微照片可以看出,由于增容剂的加入,PP与PMMA相之间的界面变得模糊,两相的相容性变好.随着PP-g-MAH中MAH接枝率的增加,PMMA分散相的尺寸减小且变得均匀;当增容剂的接枝率为2.41%,添加的质量分数为4.71%,PP/PMMA共混体系中PMMA分散相的相?尺寸可达最小.PP-g-MAH作为反应型增容剂,一方面与PP在界面区域产生共晶;另一方面,MAH极性基团与PMMA的极性基团间产生的强的化学键合作用,使得界面区域的PP-g-MAH分子采取有利于降低构象熵的构象来起到增容作用.PP/PMMA共混物在130℃等温结晶的结果显示,PMMA相对PP的结晶形态的影响较小,PP结晶呈现典型的均相成核特征.PP/PMMA共混体系中加入PP-g-MAH,PP结晶尺寸减少.与非等温结晶相比,等温结晶的PP/PMMA共混物中PMMA相区尺寸明显偏大.     

几种典型固体聚合物体系的^13C自旋—晶格弛豫特性

用固体高分辨ＮＭＲ系统地研究了几种典型的均聚物，共聚物，聚合物共混物以及用接枝共聚物增容的不相容聚合物共混体系的＾１３Ｃ自旋－晶格弛豫特性。研究结果表明：＾１３Ｃ自旋－晶格弛豫时间是表征固体聚合物体系的很有用参数，它能提供有关本体聚合物微观形态结构的信息，并要望建立聚合物的微观怀宏观性能的关系，它不仅能准确无误地反映共混体系中可能存在的各种相互作用，而且能定性地给出相互作用的大小和准确地指明相互     

共聚物增容剂对高分子共混物形态与流变行为的影响

共聚物增容剂可以提高不相容高分子共混物两相的相容性,从而强化共混物的宏观机械性能。增容剂通过对共混物界面性质的改善,对共混物的相形态和粘弹性都有很大的影响。目前对增容作用的研究已不再局限于对其增容原理的探索及增容效果的评价,还集中于揭示增容剂对高分子共混物在流场下的形态演变与流变行为的影响。本文从上述方面对近期的研究进展进行了总结,并归纳了增容剂的分子结构、加工条件等因素对流场下增容体系微观结构形成的影响。     

Nanostructured carbon black filled polypropylene/polystyrene blends containing styrene-butadiene-styrene copolymer: Influence of morphology on electrical resistivity

This paper is part of a comprehensive study on using selective localization of carbon black (CB) at the interface of immiscible polymer blends in order to reduce the percolation threshold concentration and enhance the conductivity of the blends. CB was successfully localized at the interface of polypropylene/polystyrene (PP/PS) blend by introducing styrene-butadiene-styrene (SBS) tri-block copolymer to the blend. In CB-PP/PS/SBS blends, CB has higher affinity for the polybutadiene (PBD) section of the SBS copolymer, whereas in CB-PP/PS blends, CB prefers the PS phase. PP/PS interface is one of the preferred locations for the SBS copolymer in the (PP/PS) blend; at which the PBD section of the SBS copolymer forms a few nanometers thick layer able to accommodate the CB nano-particles. The influence of SBS addition on the morphology and electrical properties of various PP/PS blends filled with 1 vol% CB were studied. SBS influence on the conductivity of PP/PS blends was found to be a function of the PP/PS volume ratio and SBS loading. The most dramatic increase in conductivity was found in the (60/40) and (70/30) PP/PS blends upon the addition of 5 vol% SBS. 5 vol% SBS was found to be the optimum loading for most blends. Using 10 vol% of SBS was reported to deteriorate electrical conductivity of the conductive co-continuous PP/PS blends. For all blends studied, SBS addition was found to compatibilize the blends. Finer morphologies were obtained by increasing SBS loading.     

聚ε-己内酯/聚氯乙烯球晶表面的XPS研究

聚合物薄膜在微电子领域中的应用日益增加.聚ε-己内酯/聚氯乙烯（PCL/PVC）是研究得最广泛的聚合物共混薄膜之一.PCL与PVC以一定比例混合时,可以形成环带球晶；同时,体系分为结晶PCL相及PCL/PVC非晶混溶相.用XPS和成象XPS分析技术,对PCL/PVC膜的表面化学组成和元素分布情况进行了研究.观察到PCL在薄膜表面富集.此外,成象XPS表明,PVC在球晶边界处富集,且球晶边界宽度约15 μm.     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

ABS／PVC共混体系的相容性,力学性能和形态

通过掺和各种橡胶聚合物如ABS、MBS和天然橡胶等，使聚氯乙烯（PVC）的低抗冲击强度和难加工性得到改进「‘，’‘．ABS和PVC的共混物具有优异的抗冲击强度、刚性、韧性和耐化学性等．这与两聚合物的组份比、相容性及形态结构密切相关“，“．将丙烯睛（SAN）共聚单体引人聚苯乙烯（陀）和丁二烯（孤）后，使＊踞／＊＊C具有好的相容性D’．本文对＊踞”＊C共混体系的不同共混组份，同一共混条件下的相容性，力学性能和形态结构进行了研究．ABS（通用型301树脂，兰州化学工业公司）；PVC－SG－3型（吉林化学工业公司），稳定剂…     

Effect of preparation method on nanoscopic structure of conductive SBS/PANI blends: Study using small‐angle X‐ray scattering

Small‐angle X‐ray scattering (SAXS) studies of electrically conductive blends based on polyaniline–dodecylbenzenesulfonic acid (PANI–DBSA)/styrene–butadiene–styrene (SBS) triblock copolymer were performed to investigate the influence of the blend preparation procedure on the nanoscopic structure of the blends. The blends were prepared by mechanical mixing (MM) procedure and by in situ polymerization (ISP) of aniline in the presence of SBS. The results indicate that pure PANI–DBSA presents an extended phase consisting of crystalline islands of nanometric size, with a good spatial correlation between them, embedded into an amorphous PANI phase. This feature was not observed in SBS/PANI–DBSA blends prepared by MM or ISP. In MM blends, the PANI phase is constituted by smaller domains, containing poorly spatially correlated crystalline islands, whereas in ISP blends with low or medium amount of PANI, there is no SAXS peak which could be related to a spatial correlation between PANI crystalline islands. The conductivity of the ISP blends is higher when compared to MM blends because of the higher homogeneity at nanometric scale. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3069–3077, 2007     

COMPATIBILITY OF PVC WITH POLYURETHANES OF DIFFERENT SOFT SEGMENTS

Blends of PVC and polyurethanes with four different soft segments of molecular weight 1000 were prepared and studied by dynamic mechanical and DSC techniques. It was found that the compatibility of PVC with segmented polyurethanes was related to the mixing of PVC molecules and the soft segments of the polyurethanes. Polyester based polyurethanes are more compatible with PVC than polyether based polyurethanes. Solution cast blends of PVC with PCL-polyurethane (1/2/1) exhibit single and narrow glass transition, while the blends with PPO-polyurethane (1/2/1) are completely incompatible. The compatibility was found to decrease with increasing hard segment content for all the polyurethanes used. The methods of blend preparation may change the compatibility of PVC/PU blends through their influence on the mixing or demixing of the hard and soft segments.     

PVC／PE交联共混体系的动态力学研究

在ＰＶＣ／ＰＥ共混体系中加入交联剂和引发剂能产生ＰＶＣ－ＣＯ－ＰＥ共聚物，这种共聚物在共混物中可起到增容剂的作用。通过动态力学分析和扫描电镜研究了ＰＶＣ／ＰＥ交联共混体系的相容性。发现引发剂、交联剂、稳定剂和增塑剂等对共混物中的交联反应均有较大的影响。     

Thermal dehydrochlorination of poly(vinyl chloride)—epoxidized butadiene/styrene triblock copolymer blends

The effect of the type of epoxidized butadiene/styrene block copolymer [ESBS; linear (B/S) or radial (E(B/S)_n), containing 0–27% of epoxy groups] on the thermal dehydrochlorination of poly (vinyl chloride) (PVC)-ESBS blends (ESBS content 10%) was investigated in the temperature range 170–180 °C, under a non-oxygen atmosphere. Thermal stability of the PVC-ESBS blends was estimated on the basis of induction time, t₀, and maximum rate of hydrochloride emission, V_max from the system. It was found that, for a similar degree of epoxidation of the SBS copolymer, the induction time i.e. the time after which emission of HCl begins, is longer in the series PVC < PVC-SBS < PVC-EB/S < PVC-E(B/S)_n, and the same is true for thermal stability. However, the maximum rate of emission of HCl is lowest in the case of PVC-EB/S blends, in the range of molar ratios from 0.5 to 2.0 × 1O⁻². On the basis of the dependence V_max = f(EB/VC), it was found that there is a certain content of epoxidized butadiene (EB) units in a mixture which causes the optimum stability of poly (vinyl chloride) during heating. During thermal destruction of the PVC-ESBS blends, the HC1 evolved undergoes addition both to epoxy fragments and to double bonds. The degree of conversion of EB units in time t₀ is 20% at 170 °C and 30% at 180 °C. The glass transition temperature, T_g, of PVC in the PVC-ESBS blends shifts towards higher temperatures by about 6–8 °C, proving the existence of crosslinking processes during moulding of the blends. The epoxidized butadiene/styrene radial block copolymer, E(B/S)_n, is a better thermal stabilizer of PVC than the linear EB/S copolymer.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.