浆态床F-T合成Fe/Cu/K/SiO2催化剂中K助剂作用的研究

采用低温N2吸附、H2 TPR、CO2 TPD、MES、XRD,考察了K的加入顺序对两组微球状费托(F-T)合成Fe/Cu/K/SiO2催化剂的织构性质、还原行为、碳化行为、物相变化以及反应性能的影响。结果表明,K的加入顺序对催化剂的织构性质影响很小。先加Si后加K的催化剂具有较强的表面碱性,抑制催化剂在H2气氛下的初始还原,但促进了催化剂的碳化,且在浆态床F T反应中表现出良好的反应稳定性,较高的FTS反应活性,较低的甲烷选择性以及较高的重质烃和烯烃选择性,表现出良好的工业应用前景。     

不同放大级Fe/Cu/K/SiO2催化剂的表征及其浆态床费托合成反应性能

采用连续共沉淀和喷雾干燥成型相结合的方法,制备了实验室级和放大级微球状费托(FT)合成Fe/Cu/K/SiO2催化剂.实验室级催化剂的颗粒尺寸为5～15μm,放大级催化剂的颗粒尺寸为40～60μm.利用低温N2物理吸附、H2程序升温还原、CO2程序升温脱附、穆斯堡尔谱和X射线衍射等表征手段考察了催化剂的织构性质、还原行为、碳化行为及物相变化.结果表明,与实验室级催化剂相比,放大级催化剂具有较大的晶粒尺寸和孔径、较小的比表面积和较弱的表面碱性,催化剂的还原和碳化受到抑制.浆态床FT合成反应及扫描电子显微镜结果表明,放大级催化剂经诱导期达到稳定状态后,转化率可达到实验室级催化剂的水平,且具有很高的稳定性、重质烃选择性及抗磨损性.     

制备方法对Fe/NCNTs催化剂结构及费托反应性能的影响

以碳氮纳米管(NCNTs)为载体, 利用氮的锚定作用, 采用三种不同的制备方法(等体积浸渍法、胶体法和沉积沉淀法)方便地构建了负载铁物种的Fe/NCNTs催化剂. 系统考察了制备方法对催化剂的结构及费托反应性能的影响. 结果表明, 制备方法影响铁纳米粒子的粒度和分布、催化剂的还原和碳化行为, 使催化剂表现出不同的催化性能. 等体积浸渍法得到分散性较好、粒径小和分布窄[(8±4) nm]、容易还原和碳化的催化剂, 反应中呈现出最高的低碳烯烃选择性、催化活性和稳定性. 胶体法得到了形貌各异的粒子, 反应中活性相易被氧化使得催化剂活性及稳定性较差. 沉积沉淀法得到了粒径过大、难以还原和碳化的粒子, 反应15 h后催化剂活性及稳定性急剧下降. 该研究为利用氮掺杂碳纳米材料作为载体设计和开发高性能的费托合成催化剂提供了有益参考.     

Cr 助剂对 Fe 基催化剂结构和费托合成性能的影响

 采用 N2 吸附-脱附、X 射线衍射、穆斯堡尔谱、X 射线光电子能谱、程序升温还原和热重分析等技术研究了助剂 Cr 含量对 Fe 基费托合成催化剂的织构性质、还原行为以及物相变化的影响. 在 H2/CO = 2.0, 260~300 oC, 1.5 MPa 和 2 000 ml/(g•h) 条件下, 在固定床反应器中考察了 Cr 含量对 Fe 基催化剂费托合成反应活性和产物烃选择性的影响. 结果表明, 在氧化态催化剂中, Cr 助剂与 Fe 物相存在较强的相互作用, 形成固溶体相 α-(Cr1-xFex)2O3; 随着 Cr 含量的增加, 逐渐由单一的富 Fe 相 α-(Fe1-xCrx)2O3 向富 Fe 相和富 Cr 相 α-(Cr1-yFey)2O3 两相过渡. Fe-Cr 固溶体的生成显著抑制了催化剂的还原, 导致催化剂还原度降低, 因而催化剂活性下降. 同时, Cr 的添加提高了甲烷和轻质烃选择性, 但抑制了水煤气变换活性.     

Cu、K助剂对FeMn/SiO2催化费托合成的影响

研究了Cu、K助剂对共沉淀型FeMn/SiO2催化剂还原行为、吸附行为及费托(F-T)合成活性和选择性的影响. Cu助剂以与Fe、Mn、SiO2共沉淀的方式引入, 而K助剂是在喷雾干燥前均匀加入沉淀浆料引入的. 结果表明, Cu可明显提高催化剂的还原性能, K助剂能促进催化剂在CO中的还原但抑制在H2中的还原, 而同时加入Cu和K会进一步促进催化剂在H2或CO中的还原; Cu助剂能促进H2吸附而K助剂对H2吸附无明显影响; Cu在一定程度上提高了F-T合成活性, 缩短了反应诱导期, K明显促进了CO的转化而相对抑制了H2的转化, 并且延长了反应的诱导期, Cu与K协同作用不仅提高反应的转化率而且缩短了反应的诱导期; K使得烃产物平均分子量增加, Cu单独对烃产物分布影响不明显, 而与K共同作用会进一步增加烃产物的分子量.     

低温高活性熔铁催化剂上的超临界相费托合成反应

在固定床反应器中超临界相条件下研究了熔铁催化剂上的费托合成反应,发现在超临界介质中反应物和产物更容易扩散,较好地抑制了催化剂表面非活性碳的沉积,从而提高了费托合成反应中的CO转化率和烯烃选择性,增加了链增长因子,降低了甲烷选择性.同时,考察了超临界介质、反应温度、压力、H2/CO比和空速等条件对费托合成反应的影响.结果表明,C5-8正构烷烃在催化剂活性温度下都是适宜的超临界介质.当温度和压力都在介质的临界点以上时,介质表现出较好的传质与传热性能,可改善费托合成反应性能.     

Effects of calcination and reduction temperature on the performance of Co-Pt-ZrO2/γ-A12O3 catalysts for Fischer-Tropsch synthesis

采用浸渍法制备了Co-Pt-ZrO2/γ-Al2O3催化剂,对其进行了BET、XRD和TPR等表征,并在浆态床反应器上考察了焙烧温度和还原温度对催化剂费托合成反应性能的影响.结果表明,焙烧温度过高,容易造成Co物种和载体间的相互作用增强,使部分氧化钻颗粒聚集或烧结,导致催化剂的F-T合成反应活性和C5+烃选择性降低.还原温度较低时,钴物种不能充分还原,CO加氢活性低,甲烷选择性高,重质烃选择性低;还原温度过高,则可能造成活性物种的烧结,反而降低了催化剂的活性和重质烃选择性.在原料气n(H2)/n( CO)=2.0、483 K、2.4 MPa和空速3.6 L/( gcat·h)的条件下,31.08％ Co～0.11％Pt ～ 7.16％ ZrO2/Al2O3催化剂在673 K焙烧.纯H2下653 K还原后,其费托性能最佳;CO转化率为27.0％,C5+的选择性为83.0％.     

Ru和Cu助剂对费托合成Fe基催化剂反应性能的影响

研究了Ru和Cu助剂对无K的费托(F-T)合成Fe基催化剂的织构性质、物相结构、还原和碳化行为的影响.在n(H2)/n(CO)=2.0,t=260℃,P=1.5MPa和GHSV=2000h-1的条件下,采用固定床反应器考察了Ru,Cu助剂对Fe基催化剂费托合成反应性能的影响.采用低温N2物理吸附、X射线衍射、穆斯堡尔谱...     

Effects of Zn promoter on the structure and Fischer-Tropsch performance of iron catalyst

采用低温N2吸附、XRD、MES、CO-TPR和H2-DTG研究了Zn(100 gFe/x gZn,x=7～100)助剂对Fischer-Tropsch(F-T)合成Fe基催化剂的织构性质、还原行为以及相变结构的影响；在H2/CO=2.0、260℃、1.5 MPa和4000 mL/(g·h)条件下在固定床反应器上考察了Zn助剂含量对Fe基催化剂F-T合成反应活性、烃产物选择性和运行稳定性的影响.研究结果表明,随着Zn含量的增加,氧化态催化剂的物相由α-Fe2O3和ZnFe2O4逐渐向ZnFe2O4和ZnO转变,ZnFe2O4在催化剂中优先生成,只有在超出其计量比1∶2之后才有ZnO出现.由于ZnFe2O4较为稳定,能够促进催化剂中Fe物相的分散,导致比表面积增加.在还原和反应态催化剂中,ZnFe2O4一方面抑制催化剂的过度还原和碳化；另一方面表现为稳定活性相铁碳化物.催化剂的F-T反应性能评价结果表明,纯铁催化剂由于铁碳化物氧化而迅速失活,而Zn助剂催化剂却由于ZnFe2O4的稳定作用,活性较为稳定.同时,由于催化剂在反应初相变的影响,导致Zn助剂催化剂的初始烯烃选择性随着Zn含量的增加而增加,在相态稳定之后选择性趋于一致.     

还原气氛对钴锆共沉淀催化剂结构和费托合成反应性能的影响

采用程序升温还原、氮吸附、原位X射线衍射、扫描电镜和透射电镜等方法研究了不同还原气氛对钴锆共沉淀催化剂结构的影响,并考察了催化剂上费托合成反应的性能.结果表明,H2还原对催化剂的破坏程度较小,活性相主要是面心立方钴;CO还原导致催化剂发生积碳,催化剂中出现面心立方钴和六方钴的混晶;合成气还原使催化剂烧结严重,单质钴以面心立方和六方两种晶相存在.费托合成反应结果表明,CO还原后催化剂没有催化性能,H2还原与合成气还原后催化剂的催化活性相差不大,但前者CH4选择性较低.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.