氮气吹扫和费托合成的脉冲过程以提高α-烯烃的选择性（英文）

费托合成可以将煤炭或者生物质气化得到的合成气转化为α-烯烃等重要的化工产品。研究将费托合成和氮气吹扫操作组合成一脉冲过程,在稳定的操作状态下保证费托合成和氮气吹扫交替进行。在传统的费托合成条件下(反应气速为2 000 h~(-1),温度为497 K,压力为2.0 MPa,氢碳体积比为2.0)考察了Fe-Co催化剂在脉冲过程中费托合成的活性和选择性。结果表明,N_2吹扫温度和压力分别为517 K和0.2 MPa下的费托合成的C_3烯烷比是未脉冲的相同反应条件下的九倍左右。同时,反应过程中CH_4的选择性和CO的转化率有所下降。在此基础上,通过间歇反应在固定床反应器中进行该脉冲过程,实验结果表明,利用脉冲操作在费托反应中可以获得更高的烯烃选择性。     

超临界相CO加氢合成甲醇,异丁醇的研究

以正十一～十三烷的混合物为超临界介质,在反应温度３６０～４１０℃、合成气压力７５ＭＰａ、进气空速１７００ｈ－１、介质压力１７８ＭＰａ、总压９３ＭＰａ的实验条件下,研究了固定床反应器中Ｚｎ－Ｃｒ、Ｃｕ－Ｚｎ－Ｃｒ催化剂在超临界相和气相条件下合成甲醇、异丁醇的性能。结果表明,超临界相反应的ＣＯ转化率高于气相反应。在超临界条件下反应,醇类选择性随着温度升高下降较慢,而气相反应醇类选择性随着温度升高下降较快。气相反应产物以甲醇、异丁醇为主,含少量乙醇和正丙醇,超临界相反应的产物分布与气相反应的明显不同,甲醇含量减少,乙醇、正丙醇和异丁醇都有不同程度增加。超临界流体的存在对合成醇链增长有影响,在不同催化剂上的产物分布有较大差异     

氮气吹扫和费托合成的脉冲过程以提高α-烯烃的选择性

费托合成可以将煤炭或者生物质气化得到的合成气转化为α-烯烃等重要的化工产品。研究将费托合成和氮气吹扫操作组合成一脉冲过程,在稳定的操作状态下保证费托合成和氮气吹扫交替进行。在传统的费托合成条件下(反应气速为2 000 h^-1,温度为497 K, 压力为 2.0 MPa, 氢碳体积比为2.0)考察了Fe-Co催化剂在脉冲过程中费托合成的活性和选择性。结果表明,N₂吹扫温度和压力分别为517 K和0.2 MPa下的费托合成的C₃烯烷比是未脉冲的相同反应条件下的九倍左右。同时,反应过程中CH₄的选择性和CO的转化率有所下降。在此基础上,通过间歇反应在固定床反应器中进行该脉冲过程,实验结果表明,利用脉冲操作在费托反应中可以获得更高的烯烃选择性。     

Effect of reduction temperature on the properties and Fischer-Tropsch synthesis performance of Fe-Mo catalysts

研究了还原温度对Fe-Mo催化剂性质及费托(F-T)合成性能的影响.采用N2物理吸附、X射线衍射、穆斯堡尔谱和H2程序升温脱附技术对催化剂进行了表征.结果表明,随还原温度升高,金属铁晶粒粒径增大,金属铁上的H2吸附量先升后降;催化剂还原度提高,反应态催化剂碳化铁含量递增.催化剂F-T合成性能在280℃、1.5MPa、2000h-1、合成气H2/CO比为2.0条件下在固定床反应器中测试.反应结果表明,随还原温度提高,催化剂接近稳态时的活性和重质烃选择性(C5+)先升后降,而甲烷选择性则先降后升.350℃还原催化剂具有最佳F-T合成反应性能.     

SUPERCRITICAL-PHASE PROCESS FOR SELECTIVE SYNTHESIS OF HEAVIER HYDROCARBONS FROM SYNGAS OVER ARu/Al_2O_3 CATALYST

在Ｒｕ／Ａｌ２Ｏ３催化剂上进行了超临界条件下的固定床费托合成。研究了催化剂孔尺寸、α－Ｃ１４烯共进料和反应温度对费托合成产物分布的影响     

Effects of calcination and reduction temperature on the performance of Co-Pt-ZrO2/γ-A12O3 catalysts for Fischer-Tropsch synthesis

采用浸渍法制备了Co-Pt-ZrO2/γ-Al2O3催化剂,对其进行了BET、XRD和TPR等表征,并在浆态床反应器上考察了焙烧温度和还原温度对催化剂费托合成反应性能的影响.结果表明,焙烧温度过高,容易造成Co物种和载体间的相互作用增强,使部分氧化钻颗粒聚集或烧结,导致催化剂的F-T合成反应活性和C5+烃选择性降低.还原温度较低时,钴物种不能充分还原,CO加氢活性低,甲烷选择性高,重质烃选择性低;还原温度过高,则可能造成活性物种的烧结,反而降低了催化剂的活性和重质烃选择性.在原料气n(H2)/n( CO)=2.0、483 K、2.4 MPa和空速3.6 L/( gcat·h)的条件下,31.08％ Co～0.11％Pt ～ 7.16％ ZrO2/Al2O3催化剂在673 K焙烧.纯H2下653 K还原后,其费托性能最佳;CO转化率为27.0％,C5+的选择性为83.0％.     

Zr-Mn-K催化剂超临界相合成甲醇与异丁醇的研究

用共沉淀法和超临界流体干燥法,分别制备了Ｚｒ－Ｍｎ－Ｋ沉淀型催化剂和超细催化剂．以正十一～十三烷的混合物为超临界介质,在反应温度３６０～４１０℃、合成气压力７．５ＭＰａ、ＧＨＳＶ１７００ｈ－１及介质压力２．０８ＭＰａ的实验条件下,分别考察了超细催化剂和沉淀催化剂的气相和超临界相催化合成气制甲醇、异丁醇的性能．气相和超临界相反应的研究均表明,超细催化剂催化合成异丁醇的活性高于沉淀催化剂;在超临界条件下反应,超细催化剂上产物的异丁醇含量较高（为２３％～３２％）,甲醇含量为２２％～３３％,其它醇均在１０％左右．气相与超临界相反应结果的对比显示,超临界流体促进产物的脱附与传递,提高了ＣＯ的转化率．但超临界流体对甲烷的萃取作用强于对醇的萃取,醇选择性低于气相反应．在超临界条件下合成甲醇、异丁醇仍遵循异丁醇形成的链增长机理,超临界流体改变了链增长各步骤的相对速度,致使超临界相反应的产物分布不同于气相反应的产物分布．     

超临界二氧化碳中羰基钴催化的端基炔烃环三聚反应研究

原子经济性良好的炔烃[2+2+2]环加成反应与绿色溶剂超临界二氧化碳相结合,是一个符合绿色化学原则的环境友好反应过程.建立了一个纯超临界二氧化碳介质中八羰基二钴催化的端基炔烃环三聚反应体系,在优化的反应条件下,以较高产率选择性地制备1,2,4-三取代苯衍生物.优化了催化剂用量、二氧化碳压力、反应温度及时间等反应条件,讨论了反应物料及催化剂在超临界二氧化碳介质中的溶解性和相行为,提出了端基炔烃环三聚反应机理,并将反应底物从C≡C键拓展至C≡N键,对超临界二氧化碳介质中炔-腈环加成反应进行了初步探索.优化出的炔烃环三聚催化反应体系无需使用有机助溶剂和各类助剂,底物适应性好,产物选择性高,为合成1,2,4-三取代苯衍生物提供了一种绿色合成方法.     

超临界合成Pt修饰的TiO2用于光催化CO2还原制备太阳能燃料

考察了超临界条件下合成TiO2基光催化剂的性质,尤其是在超临界CO2下得到的分散在TiO2上Pt的特性,并与商品化TiO2性能进行了比较.另外,所得催化剂的光催化活性用CO2光还原制太阳能燃料进行了评价.结果表明,该催化剂可得到具有比商用TiO2更好或类似的性能(高比表面积、结晶度、表面羟基浓度,大的孔容、增强的可见光吸收、高的甲烷生成速率)而用于CO2还原制备燃料的反应中.这可归因于该催化剂超临界介质合成过程.     

还原温度对Fe-Mo催化剂性质及F-T合成性能的影响

研究了还原温度对Fe-Mo催化剂性质及费托(F-T)合成性能的影响。采用N₂物理吸附、X射线衍射、穆斯堡尔谱和H₂程序升温脱附技术对催化剂进行了表征。结果表明,随还原温度升高,金属铁晶粒粒径增大,金属铁上的H₂吸附量先升后降;催化剂还原度提高,反应态催化剂碳化铁含量递增。催化剂F-T合成性能在280 ℃、1.5 MPa、2 000 h^-1、合成气H₂/CO比为2.0条件下在固定床反应器中测试。反应结果表明,随还原温度提高,催化剂接近稳态时的活性和重质烃选择性(C₅⁺)先升后降,而甲烷选择性则先降后升。350 ℃还原催化剂具有最佳F-T合成反应性能。     

STUDIES ON FISCHER TROPSCH SYNTHESIS OVER Fe-Cu-K CATALYST Ⅰ.CATALYTIC PERFORMANCE

The influence of reaction pressure, temperature, space velocity (GHSV), particle size of catalyst and H2/CO ratio of feed-gas on the steady-state product distribution, conversion of CO, H2 and syngas, olefin to paraffin ratio and CO2/ H2O ratio for FTS reaction were investigated using a coprecipitated copper- potassium promoted iron catalyst. The test was carried out in a fixed-bed reactor. Increasing the reaction temperature from 493. 2 to 5-13. 2 K shifted the hydrocarbon distribution toward the heavier hydrocarbons (C5-C23) and selectively increased CO conversion to CO2. The hydrocarbon distribution was found to be dependent on the H2/CO feed-gas ratio in the range from 1.23 to 2. 22. The CO2/H2O ratio in product decreased as the flow of feed-gas rate increased, which suggests that H2O is a primary product and its reaction with CO to form CO2 occurs via a secondary process. The CO conversion increased with the decrease of catalyst particle size from 10 to 60 mesh (2. 0- 0. 3 mm), while the CO convers     

环己烯在超临界CO2介质中的催化氧化

首次用（ＮＨ４）６Ｍｏ７Ｏ２４－Ｐｔ／ＳｉＯ２催化剂,在超临界ＣＯ２介质中催化气氧化环己烯。系统地研究了反应温芳和压力对环己烯转化率的影响及反应温度和压力对产物分布和选择性的影响,测定了催化剂的活性组份的流失情况。     

工业固定床Fe-Cu-K催化剂浆态床F-T合成适应性研究

采用连续搅拌釜式反应器,在接近F-T合成实际工况下考察了工业固定床Fe-Cu-K催化剂浆态床F-T合成反应性能，研究反应温度、压力、原料气空速和氢碳摩尔比等操作参数对催化剂反应活性、产物选择性和稳定性的影响，实验总运转时间达2 500 h；同时采用扫描电镜技术（SEM）对催化剂的抗磨损性能进行了研究，结果表明，操作参数对催化剂的活性、选择性和目标产物产率有较大的影响，工业固定床Fe-Cu-K催化剂具有一定的抗磨损性能，F-T合成烃产物分布合理；催化剂具有较高的稳定性，在589 h的稳定条件运行内，催化剂的失活速率为0.23%/d（以CO转化率的降低计）；在整个运行期间CH4选择性维持在较低的水平。     

Characterization and catalytic behavior of EDTA modified silica nanosprings (NS)-supported cobalt catalyst for Fischer-Tropsch CO-hydrogenation

The effect of ethylene diamine tetraacetic acid(EDTA) modification on the physico-chemical properties and catalytic performance of silica nanosprings(NS) supported cobalt(Co) catalyst was investigated in the conversion of syngas(H~(2+) CO) to hydrocarbons by Fischer-Tropsch synthesis(FTS). The unmodified Co/NS and modified Co/NS-EDTA catalysts were synthesized via an impregnation method. The prepared Co/NS and Co/NS-EDTA catalysts were characterized before the FTS reaction by BET surface area,X-ray diffraction(XRD),transmission electron microscopy(TEM),temperature programmed reduction(TPR),X-ray photoelectron spectroscopy(XPS),differential thermal analysis(DTA) and thermogravimetric analysis(TGA) in order to find correlations between physico-chemical properties of catalysts and catalytic performance. FTS was carried out in a quartz fixedbed microreactor(H_2/CO of 2 ∶1,230 ℃ and atmospheric pressure) and the products trapped and analyzed by GC-TCD and GC-MS to determine CO conversion and reaction selectivity. The experimental results indicated that the modified Co/NS-EDTA catalyst displayed a more-dispersed phase of Co_3O_4 nanoparticles(10.9%) and the Co_3O_4 average crystallite size was about 12.4 nm. The EDTA modified catalyst showed relatively higher CO conversion(70.3%) and selectivity toward C_(6-18)(JP-8,Jet A and diesel) than the Co/NS catalyst(C_(6-14))(JP-4).     

Nanosized cobalt-based catalyst prepared by supercritical phase condition for Fischer-Tropsch synthesis

A series of nanosized Co/Zn/Mn/K composite catalysts for Fischer-Tropsch synthesis (FTS) were prepared by supercritical fluid drying (SCFD) method and common drying (CD) method. The nanosized cobalt-based catalysts were characterized by XRD, TEM and BET techniques. Their catalytic performances were tested in a slurry-bed reactor under FTS reaction conditions. The drying and crystallization were carried out simultaneously during SCFD, therefore, the catalysts prepared by SCFD method have ideal structure and show the FTS performance superior to the others prepared by CD method. The FTS activity and selectivity were improved via adding Zn, Mn and K promoters, and less CH₄ and CO₂ as well as higher yield of C₅₊ products were achieved. The optimal performance of a 92% CO conversion and a 65% C₅₊ product yield was obtained over a catalyst with the component of Co/Zn/Mn/K = 100/50/10/7. Furthermore, the catalytic performance was studied under the conditions of liquid-phase and supercritical phase slurry-bed, and C₅₊ product yield were 57.4% and 65.4%, respectively. In summary, better catalytic performance was obtained using the nanosized catalyst prepared by SCFD method under supercritical reaction conditions, resulting in higher conversion of CO, less CO₂ byproduct, and higher yield of C₅₊ products.     

Effect of Potassium Addition on Coprecipitated Iron Catalysts for Fischer-Tropsch Synthesis Using Bio-oil-syngas

The effects of potassium addition and the potassium content on the activity and selectivity of coprecipitated iron catalyst for Fischer-Tropsch synthesis (FTS) were studied in a fixed bed reactor at 1.5 MPa, 300 o C, and contact time (W=F) of 12.5 gcath/mol using the model bio-oil-syngas of H2/CO/CO2/N2 (62/8/25/5, vol%). It was found that potassium addition increases the catalyst activity for FTS and the reverse water gas shift reaction. Moreover, potassium increases the average molecular weight (chain length) of the hydrocarbon products. With the increase of potassium content, it was found that CH4 selectivity decreases and the selectivity of liquid phase products (C5+) increases. The characteristics of FTS catalysts with different potassium content were also investigated by various characterization measurements including X-ray diffraction, X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller surface area. Based on experimental results, 100Fe/6Cu/16Al/6K (weight ratio) was selected as the optimal catalyst for FTS from bio-oil-syngas. The results indicate that the 100Fe/6Cu/16Al/6K catalyst is one of the most promising candidates to directly synthesize liquid bio-fuel using bio-oil-syngas.     

超临界和近临界条件下Fischer Tropsch合成研究：溶剂的影响

研究了超临界和近临界条件下费托合成过程中溶剂对反应行为的影响。反应在固定床反应器中进行，催化剂为Co/SiO2，所选择的溶剂有两类：纯溶剂（正戊烷和正己烷）和混和溶剂（由正己烷和少量的C5~10烃组成）。结果表明,正己烷分压对CO转化率影响很小，但是产物中1 烯烃含量随正己烷分压增加而增加，超临界条件下1 烯烃含量明显高于非临界条件下。溶剂的种类对CO转化率、CH4和CO2选择性以及产物炭分布影响不大。这一结果表明为了减少溶剂用量，对含有适量轻组分（C5~10）的正己烷溶剂进行循环使用是可行的。结果同时表明与正己烷相比，混和溶剂（25%正己烷和75%正葵烷）具有较高的1 烯烃选择性。     

Activation pressure studies with an iron-based catalyst for slurry Fischer-Tropsch synthesis

Fischer-Tropsch synthesis (FTS) was carried out with an industrial iron-based catalyst (100Fe/5Cu/6K/16SiO2, by weight) under the baseline conditions in a stirred tank slurry reactor (STSR). The effects of activation pressure on the catalyst activity and selectivity were investigated. It was found that iron phase compositions, textural properties, and FTS performances of the catalysts were strongly dependent on activation pressure. The high activation pressure retards the carburization. Møssbauer effect spectroscopy (MES) results indicated that the contents of the iron carbides clearly decrease with the increase of activation pressure, especially for the activation pressure increasing from 1.0 MPa to 1.5 MPa, and the reverse trend is observed for superparamagnetic Fe3+ (spm). The higher content of Fe3+ (spm) results in the higher amount of CO2 in tail gas when the catalyst is reduced at higher pressure. The catalyst activity decreases with the increase of activation pressure. The high quantity of iron carbides is necessary to obtain high FTS activity. However, the activity of the catalyst activated in syngas can not be predicted solely from the fraction of the carbides. It is concluded that activation with syngas at the lower pressure would be the most desirable for the better activity and stability on the iron-based catalyst.     

硅对铁基费-托合成催化剂的影响

用共沉淀法制备了一系列不同硅含量的铁基催化剂,采用N2吸附和原位X射线衍射对催化剂进行了表征,在固定床反应器中考察了催化剂的费-托合成反应活性、选择性和稳定性.结果表明,含硅的催化剂具有较大的比表面积和较小的平均孔径,在CO还原及费-托合成反应中生成的碳化铁物种的稳定性比不含硅的催化剂高.在费-托合成反应中,不含硅的催化剂具有较高的初始活性,但易失活;含硅的催化剂具有较低的初始活性,但稳定性较高.Fe7C3是活性最高的碳化铁物种.随着硅含量的增加,催化剂的费-托合成反应更易生成低碳数产物.