氧化锌微米花的共振拉曼和“负热淬灭”效应

利用化学气相沉积(CVD)的方法通过热氧化高纯锌粉在硅衬底上得到氧化锌微米花. X射线衍射(XRD)结果表明，其具有六角纤锌矿晶体结构.场发射扫描电子显微镜(FE-SEM)图像表明，合成的样品是由很多长且直的ZnO亚微米棒组成的微米花， 具有六角棱柱端面，棒的长度在30μm到50μm之间.在背向共振拉曼散射光谱测量中，观测到ZnO A₁(LO)的五阶声子紫外共振拉曼散射，表明样品具有较高的晶体质量.在变温光致发光谱测量中，观察到明显的中性受主束缚激子(A⁰X)的 关键词： ZnO微米花 光致发光 共振拉曼 “负热淬灭”效应     

纳米ZnO生长及性质分析

利用低压金属有机化学气相沉积(LP-MOCVD)技术,在表面含有ZnO颗粒作为催化剂的Si(111)衬底上制备了ZnO纳米柱阵列。采用X射线衍射(XRD)、喇曼光谱(Raman)、扫描电子显微镜(SEM)、光致发光(PL)谱分析了样品的晶体结构质量、表面性质和光学性质。结果表明,生长出来的纳米ZnO具有较好的c轴择优取向性。发现氧分压对ZnO纳米柱的生长有重要影响:当氧分压较低时,生长基于VLS机制;当氧分压较高时,生长基于VS机制;通过对N2O流量的控制可实现对ZnO纳米材料的可控生长。     

Synthesis and optical properties of flower-like ZnO nanorods by thermal evaporation method

Flower-like ZnO nanorods have been synthesized by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si (1 0 0) substrates without any catalyst. The structures, morphologies and optical properties of the products were characterized in detail by using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and Raman spectroscopy. The synthesized products consisted of large quantities of flower-like ZnO nanostructures in the form of uniform nanorods. The flower-like ZnO nanorods had high purity and well crystallized wurtzite structure, whose high crystalline quality was proved by Raman spectroscopy. The as-synthesized flower-like ZnO nanorods showed a strong ultraviolet emission at 386 nm and a weak and broad yellow-green emission in visible spectrum in its room temperature photoluminescence (PL) spectrum. In addition, the growth mechanism of the flower-like ZnO nanorods was discussed based on the reaction conditions.     

Effect of strain on the structural and optical properties of Cu-N co-doped ZnO thin films

Polycrystalline ZnO thin films co-doped with Cu and N have been obtained by chemical bath deposition. Introduction of Cu and N causes the change of strained stress in ZnO films, which subsequently affects the structural and optical properties. The dependence of structural and optical properties of the ZnO films on lattice strained stress is investigated by XRD measurement, SEM, PL spectrum, optical reflection and Raman spectrum. The result of photoluminescence of Cu-N co-doped ZnO films indicates that the UV emission peaks shift slightly towards higher energy side with decrease in tensile strain and vise versa. The blue-shift of the absorption edge and up-shift of E2 (high) mode of the films can be observed in the optical reflection and Raman spectra.     

Synthesis and optical properties of pencil-like and shuttle-like ZnO microrods

The pencil-like and shuttle-like ZnO microrods have been fabricated on Si (100) substrates by chemical vapor deposition. Structure characterization results show that the microrods are perfect single crystals with the wurtzite structure along the [0001] growth direction and have diameters ranging from 100 nm to 2 μm and lengths up to 10 μm. Room-temperature photoluminescence measurements of ZnO microstructures exhibit an intensive ultraviolet peak at 390 nm and a broad peak centered at about 526 nm, which can be attributed to the free exciton emission and the deep level emission, respectively. Cathodoluminescence measurements show the same ultraviolet and green emissions as seen in the photoluminescence results. A possible growth mechanism of ZnO microrods is finally proposed.     

高质量ZnO微米棒的制备及其光学性质

利用水热法制备ZnO微米棒。醋酸镁[Mg(CH3COO)2.4H2O]、醋酸锌[Zn(CH3COO)2.2H2O]和六次甲基四胺(C6H12N4)以一定比例配置成反应溶液,把反应溶液加热到90℃,反应时间为24h,能够在硅衬底上生长高质量的ZnO微米棒。用扫描电镜(SEM)和X射线衍射仪对ZnO微米棒的晶体结构和表面形貌进行了分析,结果表明,样品为细长条棒状结构,呈现六方纤锌矿结构,长径比可达10∶1,并且在[002]方向择优生长。在样品中并未发现镁离子,它有可能扮演着催化剂的角色。对ZnO微米棒的光致发光性能进行测量,由PL光谱分析可知,样品在384nm处有一个紫外发光峰,半峰全宽为13nm,紫外发光峰强度比可见发光峰强度大的多,样品的质量较好。     

The crystallization and physical properties of Al-doped ZnO nanoparticles

Un-doped Al (0-9 at.%) nanoparticles and doped ZnO powders were prepared by the sol-gel method. The nanoparticles were heated at 700-800 °C for 1 h in air and then analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectra and photoluminescence (PL). The results of un-doped (ZnO) and Al-doped ZnO (AZO) nanoparticles were also compared to investigate the structural characteristics and physical properties. XRD patterns of AZO powders were similar to those of ZnO powders, indicating that micro-Al ions were substituted for Zn atoms and there were no variations in the structure of the ZnO nanoparticles. From the XRD and SEM data, the grain size of the AZO nanoparticles increased from 34.41 to 40.14 nm when the annealing temperature was increased. The Raman intensity of the AZO nanoparticles (Al = 5 at.%) increased when the annealing temperature was increased. Increasing the degree of crystalline not only reduced the residual stress, but also improved the physical properties of the nanoparticles.     

Nanostructure and optical properties of M doped ZnO (M=Ni, Mn) thin films prepared by sol-gel process

The transparent thin films of undoped, Mn-doped, and Ni-doped zinc oxide (ZnO) have been deposited on glass substrates via sol-gel technique using zinc acetate dehydrate, nickel chloride, and manganese chloride as precursors. The structural properties and morphologies of the deposited undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/vis spectroscopy. The analyzed results indicate that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn or Ni related phases. The band gap energy was estimated by Tauc's method and found to be 3.28, 3.26, and 3.34 eV for ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films at room temperature, respectively. Room temperature photoluminescence is observed for the ZnO, Ni-doped ZnO, and Mn-doped ZnO thin films.     

水热合成ZnO:Cd纳米棒的微结构及光致发光特性

采用水热法制备了ZnO和不同掺杂浓度的ZnO:Cd纳米棒,通过SEM,XRD、拉曼光谱等的分析,研究了ZnO和ZnO:Cd的微结构并测试分析了其光致发光特性.结果表明,ZnO和ZnO:Cd纳米棒呈六角纤锌矿结构,Cd掺杂使得纳米棒体积更小.由于内部张应力的影响,Cd掺杂使得材料光学带隙减少.当掺杂浓度为2%时,合成的材料光致发光谱中出现了位于2.67 eV处,由导带底和Zn空位(VZn)缺陷能级跃迁造成的蓝光发射峰,并且Cd的掺入使得位于2.90 eV附近的紫光发射峰强度增强,对于研究ZnO蓝紫发光器件具有重要的意义.     

衬底温度对ZnO薄膜的结构和光学特性的影响

利用等离子体辅助分子束外延(P-MBE)设备在蓝宝石衬底上通过改变生长温度,制备了不同的ZnO样品.研究了衬底温度对ZnO的结构、光学和电学性质的影响.样品的晶体结构利用X射线衍射谱进行表征.X射线衍射谱表明,所有的ZnO样品都是(002)取向的六角纤锌矿结构.随着生长温度的升高,X射线的(002)衍射峰的半峰全宽逐渐...     

在c-面蓝宝石上控制生长高质量的ZnO单晶薄膜

利用Mg O和低温Zn O的缓冲层技术,在c面蓝宝石衬底上用等离子体辅助分子束外延(P-MBE)的方法生长了高质量的Zn O单晶薄膜。通过XRD测试,Zn O薄膜样品具有c轴方向的择优取向,其(002)方向摇摆曲线的半高宽(FWHM)仅为68.4 arcsec,(102)方向摇摆曲线的半高宽(FWHM)为1 150 arcsec,显示了外延薄膜极高的晶体质量。另外从扫描电子显微测试结果和原子力显微测试结果来看,Zn O薄膜具有极为平整的表面,3μm×3μm面积内的均方根粗糙度仅为0.842 nm,接近原子级的平整。拉曼光谱(Raman)和荧光光谱(PL)测试结果显示,Zn O薄膜样品内部的应力基本释放,而且具有极低的点缺陷密度。高质量Zn O单晶薄膜的实现为Zn O基的光电器件的制备提供了坚实的基础。     

Co掺杂ZnO纳米棒的共振拉曼光谱和发光特性

采用X射线衍射(XRD)和透射电子显微镜(TEM)手段对微乳液法合成的Zn0.9Co0.1O纳米棒进行了表征.通过室温下的共振拉曼光谱和光致发光光谱手段,研究了所合成纳米材料的共振拉曼光谱和发光特性,并与体相ZnO的研究结果对比,发现合成的材料具有四阶声子紫外共振拉曼散射,而体相材料只有两阶,并观察到在紫外和可见区域所...     

退火对ZnO薄膜光学特性的影响

用射频磁控溅射法在蓝宝石衬底上制备出ZnO薄膜,通过X射线衍射(XRD)、扫描电镜(SEM)和光致发光(PL)谱等研究了退火温度对ZnO薄膜结构和光学性质的影响。测量结果显示,所制备的ZnO薄膜为六角纤锌矿结构,具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度和平均晶粒尺寸增大,(002)XRD峰半高宽(FWHM)减小,光致发光紫外峰强度增强。结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量ZnO薄膜。     

Structural and optical properties of the S-doped ZnO particles synthesized by hydrothermal method

Sulfur-doped ZnO particles have been synthesized by hydrothermal method. The structural and optical properties were studied systematically by XRD, scanning electron microscopy (SEM), and photoluminescence. SEM results show that the particle is hexagonal and the average size decreases with increasing sulfur doping, which means a retardant effect of sulfur on the growth of S-doped ZnO. XRD results show that the lattice parameters increase with more sulfur, which means an effective sulfur doping and increasing strain. Optical characterization also shows that the effective sulfur doping will enhance the green emission and suppress the near bandgap emissions.     

Synthesis and optical properties of ZnO nanorods on indium tin oxide substrate

ZnO nanorods with uniform diameter and length have been synthesized on an indium-tin oxide (ITO) substrate by using a simple thermal evaporation method which is suitable to larger scale production and without any catalyst or additives. The samples were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet-vis (UV-vis) absorption spectrum, photoluminescence (PL) spectrum and Raman spectrum. The single-phase ZnO nanorods grow well-oriented along the c-axis of its wurtzite structure on ITO substrate. The ZnO nanorods shows sharp and strong UV emission located at 380 nm without notable visible light emission in the PL spectrum, which suggests the good crystallinity of the nanorods, which was also testified by their Raman spectrum. The photodegradation of methylene orange (MO) in aqueous solution reveals that the well-arranged c-axis growth of ZnO nanorods possess evidently improved photocatalytic performance and these properties enable the ZnO nanorods potential application in UV laser.     

Synthesis and characterization of Mn-doped ZnO column arrays

Mn-doped ZnO column arrays were successfully synthesized by conventional sol-gel process. Effect of Mn/Zn atomic ratio and reaction time were investigated, and the morphology, tropism and optical properties of Mn-doped ZnO column arrays were characterized by SEM, XRD and photoluminescence (PL) spectroscopy. The result shows that a Mn/Zn atomic ratio of 0.1 and growth time of 12 h are the optimal condition for the preparation of densely distributed ZnO column arrays. XRD analysis shows that Mn-doped ZnO column arrays are highly c-axis oriented. As for Mn-doped ZnO column arrays, obvious increase of photoluminescence intensity is observed at the wavelength of ∼395 nm and ∼413 nm, compared to pure ZnO column arrays.     

Photoluminescence and field emission properties of Sn-doped ZnO microrods

Sn-doped ZnO (SZO) microrods have been fabricated by a thermal evaporation method. Effect of Sn dopant on the microstructure, morphological and composition of as-prepared SZO microrods have been investigated by X-ray diffraction (XRD), Raman, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. The influence of the doping concentration on the morphological of the microrods has been investigated. Photoluminescence (PL) of these SZO microrods exhibits a weak ultraviolet (UV) emission peak at around 382 nm and the strong green emission peak at around 525 nm at room temperature. Field emission measurements demonstrate that the SZO possess good performance with a turn-on field of ∼1.94 V/μm and a threshold field of ∼3.23 V/μm, which have promising application as a competitive cathode material in FE microelectronic devices.     

ZnO纳米带外延树枝状锯齿形缺口结构的制备及其发光特性

应用气固生长方式在没有催化剂的情况下合成出一种新奇的ZnO纳米结构．通过透射电子显微镜分析，发现这种ZnO纳米带外延晶枝直径约20 nm，在[0001]方向有着良好的外延生长取向．提出了一个模型来解释这种树枝状锯齿结构的生长．室温下光致发光测量表明这种ZnO纳米结构在382、491 nm处有一个紫外发光峰和绿光发光峰．     

ZnO纳米棒的拉曼和发光光谱研究(英文)

本文对采用湿化学方法合成的ZnO纳米棒样品的拉曼光谱和发光光谱进行了研究。由扫描电镜结果可知,合成的ZnO纳米棒具有很好的尺寸发布均匀性,直径在30 nm左右,长度大于1微米。采用显微拉曼光谱技术,得到了632.8 nm波长激发的拉曼光谱,并和体相样品的拉曼光谱进行了对比分析;由325 nm激光波长激发得到的荧光光谱可知样品具有很好的紫外发光性质。     

石墨烯对ZnO微米棒光学特性的影响

采用化学气相沉积(CVD)方法制备了具有良好结晶质量和(002)择优取向的ZnO微米棒。在此基础上,选取单根ZnO微米棒,将其部分搁置于单层石墨烯表面。光致发光(PL)谱结果表明,石墨烯不仅增强了ZnO微米棒的紫外发光强度,同时也对光场在ZnO微米棒中的分布有很大的限域作用。分析认为这是由于石墨烯的表面等离子效应引起了ZnO微米棒与石墨烯之间的光-物质相互作用导致的。在拉曼(Raman)光谱中,石墨烯对ZnO微米棒的E2(L)声子振动模和E2(H)声子振动模的强度具有明显的减弱效应,这进一步证明二者之间存在光子的传输和电荷的转移,从而导致其晶格振动受到抑制。