微流控纸芯片的加工及其分析应用的实验设计*

设计了一个使用喷墨打印法加工微流控纸芯片的实验,在经烷基烯酮二聚体(AKD)的正己烷溶液浸泡过的滤纸上,以三乙醇胺溶液为打印墨水,用喷墨打印机打印出设计好的芯片图案。滤纸加热后,打印区域呈现亲水性,非打印区域为疏水性,从而制备出纸芯片,用该纸芯片通过数字比色法实现了亚硝酸根离子的定量测定。该实验不使用昂贵仪器设备,易普及。通过实验,促使学生了解微流控芯片这一前沿科学技术,锻炼学生细致、灵巧的动手能力,激发学生科技创新活力。     

白云石制备似立方体状方解石型碳酸钙晶体及其机理研究

以轻烧白云石粉、氯化铵和二氧化碳为原料,在未使用晶型控制剂的情况下,通过蒸氨-沉钙过程制备出了似立方体状碳酸钙。研究了反应温度、溶液中钙离子浓度、通气速率、搅拌速度以及陈化时间对碳酸钙中方解石相含量以及晶体形貌的影响,并探索了沉钙反应的晶型控制机理。结果表明,在反应温度40 ℃、钙离子浓度0.05 mol/L、通碳速率100 mL/min、搅拌速度400 r/min和陈化时间2 h的条件下,制备出形貌规整、粒径分布均匀的似立方体状碳酸钙,平均粒径为5~10 μm。该研究为提升白云石的使用价值、生产高附加价值的碳酸钙产品,以及提高白云石资源的利用率提供理论基础。     

不同波长条件KDP晶体的非线性光学性质研究

采用Z扫描方法系统的研究了KDP晶体在不同激光波长条件下的非线性光学性质.当λ=355 nm,功率密度为57.92 GW/cm2和λ=532 nm,功率密度为105.94 GW/cm2时,KDP晶体均呈现强烈的反饱和吸收和自聚焦效应,其非线性吸收系数和非线性折射率分别为6.50×10 -2cm/GW,1.17×10 -2cm/GW和8.02×10 -7cm2/GW,6. 14×10 -7cm2/GW;而在1064 nm波长,功率密度为347.95 GW/cm2时KDP晶体并未表现出明显的非线性性质.结果表明,在短波长的激光作用下,KDP晶体更容易产生非线性效应,双光子吸收是KDP晶体非线性吸收的主要机制.     

多层状碱式碳酸锌微晶的制备及其脱除Cu2+性能研究

以壳聚糖(CS)为生物模板,采用低温水热法成功制备出了多层状碱式碳酸锌(ZCHO)微晶.采用XRD、SEM和TG等手段对产物的结构、形态和热学性能进行了表征,结果表明,单个ZCHO微晶颗粒均是由许多ZCHO纳米片构成的.添加适量的CS对形成多层状ZCHO微晶起到了至关重要的作用.热重分析结果表明,CS辅助得到的碳酸锌微晶热稳定性较高.等温吸附实验表明,在室温下,多层状ZCHO微晶能有效脱除水体中的Cu2,去除量与浓度关系符合Freundlich模型.最后讨论了多层状ZCHO微晶大容量去除Cu2+的可能机理.     

Crystal phase control in two-dimensional materials

It is the nature of crystals to exist in different polymorphs. The recent emergence of two-dimensional (2D) materials has evoked the discovery of a number of new crystal phases that are different from their bulk structures at ambient conditions, and revealed novel structure-dependent properties, which deserve in-depth understanding and further exploration. In this contribution, we review the recent development of crystal phase control in 2D materials, including group V and VI. transition metal dichalcogenides (TMDs), group IVA metal chalcogenides and noble metals. For each group of materials, we begin with introducing the various existing crystal phases and their structure-related properties, followed by a detailed discussion on factors that influence these crystal structures and thus the possible strategies for phase control. Finally, after summarizing the whole paper, we present the challenges and opportunities in this research direction.     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。     

One‐Step Labeling of Collagen Hydrogels with Polydopamine and Manganese Porphyrin for Non‐Invasive Scaffold Tracking on Magnetic Resonance Imaging

Biomaterial scaffolds are the cornerstone to supporting 3D tissue growth. Optimized scaffold design is critical to successful regeneration, and this optimization requires accurate knowledge of the scaffold's interaction with living tissue in the dynamic in vivo milieu. Unfortunately, non‐invasive methods that can probe scaffolds in the intact living subject are largely underexplored, with imaging‐based assessment relying on either imaging cells seeded on the scaffold or imaging scaffolds that have been chemically altered. In this work, the authors develop a broadly applicable magnetic resonance imaging (MRI) method to image scaffolds directly. A positive‐contrast “bright” manganese porphyrin (MnP) agent for labeling scaffolds is used to achieve high sensitivity and specificity, and polydopamine, a biologically derived universal adhesive, is employed for adhering the MnP. The technique was optimized in vitro on a prototypic collagen gel, and in vivo assessment was performed in rats. The results demonstrate superior in vivo scaffold visualization and the potential for quantitative tracking of degradation over time. Designed with ease of synthesis in mind and general applicability for the continuing expansion of available biomaterials, the proposed method will allow tissue engineers to assess and fine‐tune the in vivo behavior of their scaffolds for optimal regeneration.