白云石制备似立方体状方解石型碳酸钙晶体及其机理研究

以轻烧白云石粉、氯化铵和二氧化碳为原料,在未使用晶型控制剂的情况下,通过蒸氨-沉钙过程制备出了似立方体状碳酸钙。研究了反应温度、溶液中钙离子浓度、通气速率、搅拌速度以及陈化时间对碳酸钙中方解石相含量以及晶体形貌的影响,并探索了沉钙反应的晶型控制机理。结果表明,在反应温度40 ℃、钙离子浓度0.05 mol/L、通碳速率100 mL/min、搅拌速度400 r/min和陈化时间2 h的条件下,制备出形貌规整、粒径分布均匀的似立方体状碳酸钙,平均粒径为5~10 μm。该研究为提升白云石的使用价值、生产高附加价值的碳酸钙产品,以及提高白云石资源的利用率提供理论基础。     

Glass transition of hydrated wheat gliadin powders

Modulated-temperature differential scanning calorimetric and dynamic mechanical analyses and dielectric spectroscopy were used to investigate the glass transition of hydrated wheat gliadin powders with moisture absorption ranged from 2.30 db%to 18.21 db%.Glass transition temperature(I_g)of dry wheat gliadin was estimated according to the Gordon Taylor equation.Structural heterogeneity at high degrees of hydration was revealed in dielectric temperature and frequency spectra.The activation energies(E_a)of the two relaxations were calculated from Arrhenius equation.     

Theoretical investigation of the Gamow-Teller transition across N=40 shell

The Gamow-Teller transitions for pf shell nuclei with proton number less than 40 and neutron number larger than 40 were believed to be blocked, due to the full filling of the neutron orbit. However, recent experimental research shows that the Gamow-Teller transitions for these kinds of nuclei are not blocked. In this paper, we systematically calculate the GT transition of pf shell nuclei ⁷⁶Se in different truncations, and the results are compared with experimental results. It is shown that, due to correlations, the believed blocked GT transition occurs, and the shell model calculations reproduce the experimental GT strength. In addition, the electron capture rates in a stellar environment are calculated and discussed.     

纤维状填料/HDPE复合体系的导电渗流与流变渗流行为的关系

研究了纤维状导电材料不锈钢纤维(SSF)填充高密度聚乙烯(HDPE)导电复合体系的导电渗流与流变渗流行为之间的关系,并与颗粒状导电颗粒炭黑(CB)/HDPE导电复合体系进行了比较.发现当SSF含量极低(0.3vol%)时,SSF/HDPE体系即发生导电渗流现象,且导电渗流转变区域极窄;而仅当SSF含量达到4.8vol%时,该复合体系才表现出流变渗流现象,这一结果与CB/HDPE体系及纳米级导电纤维填充体系截然不同.此外,通过正温度系数效应的研究发现SSF形成的导电通路稳定性高于CB/HDPE体系.我们认为,SSF/HDPE体系呈现的这些特点均与SSF较大的直径及长径比且其导电通路及流变渗流网络的形成机理不同有关.     

气相二氧化硅填充极性低聚物的界面与流变

气相二氧化硅(FS)/低聚物纳米复合材料应用广泛于涂料、胶黏剂、锂离子电池、液体防弹衣等诸多领域.然而,极性低聚物与FS表面相互作用复杂,FS/低聚物复合材料(ONCs)的流变响应多种多样.如何实现ONCs流变行为调控,是长期困扰工业界的难题.本文详细总结了FS在ONCs领域的应用,将FS粒子间相互作用与ONCs流变性质相关联,综述ONCs界面层结构的表征、调控手段及界面层与流变行为的关系.结合本课题组对FS/极性低聚物体系界面及流变行为的研究成果,提出未来ONCs领域的2个重要方向,即研究界面结构与粒子-极性低聚物相互作用间的关系,并通过界面设计实现对纳米粒子/极性低聚物复合材料的流变行为的精确调控.     

Influence of clay on the morphology and phase separation behavior of poly(methyl methacrylate)/poly(styrene-co-acrylonitrile) blends

The effect of clay on the morphology and phase-separation behavior of poly(methyl methacrylate)/poly(styreneco-acrylonitrile)(PMMA/SAN) blends and the variation of clay dispersion have been investigated. With the evolution of phase separation in PMMA/SAN, most of the clays are first located at the boundaries between PMMA and SAN, and then gradually move to the PMMA-rich domain, owing to the affinity of clay to PMMA. The introduction of clay causes the increase of binodal and spinodal temperatures of PMMA/SAN and enlarges their metastable region, indicating the phase stabilizing effect of clay on the matrix. But the influence of clay on the cloud points obviously depends on the composition of PMMA/SAN. The selective adsorption of PMMA on the clay results in the difference between the composition of surface layer and that of polymer matrix. Hence, the clay plays the role of an agent changing the conditions of phase structure formation.     

纳米层状双金属氢氧化物改性PU/PMMA的制备及其弛豫行为

采用原位聚合法,制备了聚氨酯(PU)/聚甲基丙烯酸甲酯(PMMA)/层状双金属氢氧化物(LDH)纳米复合体系(PU/PMMA/LDH).通过广角X射线衍射(WXRD)、透射电子显微镜(TEM)对其结构和形貌进行了表征,并通过热失重(TGA)、动态力学分析(DMA)和宽频介电谱(BDRS)研究了LDH含量(φ)对PU/PMMA体系热稳定性和弛豫行为的影响.结果表明,当φ<1 wt%时,LDH在聚合物基体中以剥离结构为主,PU/PMMA/LDH体系的玻璃化温度(Tg)降低,最大损耗因子(tanδmax)增大;而当φ>1 wt%时,LDH在聚合物基体中以插层结构为主,插层结构对聚合物分子链的限制使复合体系的Tg升高、tanδmax降低.LDH表面与PU硬段间的氢键作用,使复合体系的α介电弛豫转变随φ增加而向高温方向移动,弛豫过程激活参数增大.     

Suppressing entanglement sudden death by initial system-environment correlation

This paper studies the entanglement dynamics of the system S composed of two non-interactional qubits A and B. The third qubit C is its environment, E, which only interacts with the S qubit B by the Dzyaloshinskii-Moriya spin-orbit coupling. Considering the following states as the whole (S+E): the initially S-E correlated state and the separable one, the entanglement of S has no sudden death for the former case. This result sheds some light on the control of quantum entanglement, which will be helpful for quantum information processing.     

剪切作用下纳米粘土对LDPE熔体粘弹响应的影响

以LDPE/EVA/纳米粘土复合体系为研究模型,考察了剪切作用下,分散良好的纳米粘土对聚合物基体熔体稳态及瞬态粘弹响应的影响.发现剪切作用下,纳米粘土增加了聚合物熔体粘弹特性对剪切速率、剪切应变及剪切作用史的依赖性,改变了相应的依赖关系.稳态剪切时,纳米粘土的加入使体系第一法向应力差(N1)在低剪切速率区变为负值,而在高剪切速率区N1与粘土的含量无关;同时就瞬态剪切应力及N1的应变依赖关系而言,复合体系明显不同于聚合物基体;预剪切对聚合物基体瞬态粘弹响应几乎没有影响,而当纳米粘土的加入量大于3wt%后,与未经预剪切的样品相比较,经预剪切的复合体系的瞬态剪切应力值、应力过冲程度以及稳态剪切应力值均明显下降,且预剪切前后复合体系达到稳态时其瞬态剪切应力差值随纳米粘土含量的增高而线性增加.此外,纳米粘土的添加对聚合物熔体受剪切作用的非线性粘弹响应存在影响.复合体系熔体呈现特异非线性粘弹响应,其缘由被认为是由于纳米粘土在聚合物基体中剥离分散,或聚合物分子链插层于粘土片层间,形成局部有序结构,受剪切作用而排列取向.     

LOW DENSITY POLYETHYLENE/CLAY NANOCOMPOSITES MODIFIED BY ETHYLENE COPOLYMERS： EFFECTS OF FUNCTIONALIZED SEGMENTS ON MORPHOLOGY

Melt extrusion was used to prepare binary nanocomposites of ethylene copolymers and organoclay and trinary nanocomposites of low-density polyethylene （LDPE）, ethylene copolymer and organoclay. X-ray diffraction （XRD） and transmission electron microscopy （TEM） were used to analyze the structure of the clay phase and the morphology of the nanocomposites. Influences of the comonomer in the copolymer and the content of the copolymer on the morphology of the resulting nanocomposites were discussed. The binary and the trinary composites may form intercalated or exfoliated structures depending on the interaction between the copolymer and the clay layers and the content of the copolymer.