透氧膜反应器内NiO/MgO催化焦炉煤气重整反应途径

对透氧膜反应器内焦炉煤气(COG)重整反应模型进行分析.通过H2+N2、CH4+N2、CO+N2和H2+CH4+N2混合气在透氧膜反应器内重整反应,以及有无催化剂下重整反应和催化剂床层厚度重整反应实验,推测焦炉煤气重整反应模型:首先焦炉煤气中H2在催化剂活性金属镍颗粒上吸附解离,解离后的氢向高活性位迁移"(三相界面")并与膜表面侧晶格氧(或O2-)反应生成H2O.同时CH4也可能在活性镍颗粒上裂解生成CH3*和H*,反应生成的H2O与膜表面催化剂上裂解的碳反应生成H2和CO.未反应完的H2O在催化剂床层内与剩余CH4反应生成H2和CO.     

金属-载体相互作用对CH4/CO2重整反应中Rh基催化剂抗积炭性能的影响

考察了Rh/Al2O3,Rh/SiO2和Rh/CeO2催化剂上金属-载体间相互作用对CH4/CO2重整反应抗积炭性能的影响,并与反应前后催化剂的程序升温还原和程序升温氧化(TPO)测试结果相关联.实验发现,Rh与Al2O3和SiO2载体间的相互作用越强,催化剂还原后Rh的分散度越高,晶粒越小,高分散的Rh表面生成的碳物种CHx越多,其作为活泼的反应中间体越易与CO2反应生成CO和H2.而游离态的Rh还原后晶粒较大,生成的碳物种与CO2反应能力较低,从而导致催化剂失活.TPO和CO2脉冲实验结果表明,反应过程中Rh/CeO2催化剂上反应生成的CHx物种比Rh/Al2O3和Rh/SiO2上的CHx物种更活泼.同时由于Rh-CeO2间独特的相互作用,部分CeO2还原后生成CeO2-x和氧空位,促进CO2分子的活化解离,导致生成的表面氧容易与CHx反应,从而抑制催化剂积炭.     

流化床中 CH4/C3H8 自热重整制合成气

 在流化床反应器中, 考察了 Ni/SiO2 催化剂上 CH4 或 CH4-C3H8 临氧 CO2 重整 (自热重整) 制合成气反应性能. 结果表明, 在 CH4-C3H8 混合气自热重整反应中, Ni 粒径较小催化剂的活性和抗积炭性能较高, CH4 和 CO2 转化率分别达 75.5% 和 72.6%. C3H8 比 CH4 更易解离及被氧化, 部分 C3H8 解离出来的中间产物 CHx 物种可与吸附 H 结合为 CH4, 因而降低了 CH4 的表观转化率; CHx 也可与吸附的 CO2 物种反应生成 H2 与 CO, 从而促进了 CO2 的转化.     

Rh／SiO2催化剂上甲烷部分氧化制合成气反应

 利用程序升温脱附、程序升温还原、程序升温表面反应、程序升温反应和化学捕获反应等手段，对Rh／SiO2催化剂上甲烷部分氧化制合成气反应进行了研究．结果表明，Rh／SiO2催化剂上甲烷部分氧化制合成气机理属于热解－氧化反应机理．甲烷首先在催化剂上发生解离吸附，产生具有不同H／C比的化学吸附物种CHx（x＝1～3）．其中，具有较高H／C比的CHx可能是甲烷部分氧化反应的活性物种，而具有较低H／C比的CHx可能是催化剂上积碳并导致催化剂失活的来源．活性物种CHx在活性氧物种的作用下，生成含氧中间体物种CHxO或继续脱氢．含氧中间体物种进一步分解，即生成CO和H2；CO2也可由CHx或CHxO物种进一步氧 化生成．     

甲烷催化部分氧化制合成气的反应机理

借助脉冲反应、质谱-程序升温表面反应（MS-TPSR）等技术研究了Ni／α-Al2O3催化剂上甲烷催化部分氧化制合成气（POM）的反应机理．结果表明,NiO上CH4不能解离产生H2只有当NiO被CH4还原为Ni0后,CH4才能解高产生H2,Ni0是CH4活化和POM反应的活性相;POM反应机理遵循直接氧化机理,CH4和O2均在Ni0上活化,活化过程形成的Ni…C和Niδ…Oδ物种是反应历程中的关键物种,Niδ …Oδ物种高选择性地与CH4解离产生的碳物种Ni…C反应生成CO．     

不同粒径的Ni/SiO2催化剂上CH4和CO2吸附活化的漫反射傅里叶变换红外光谱研究

 采用原位漫反射傅里叶变换红外光谱研究了CH4和CO2在不同粒径的Ni/SiO2催化剂上的吸附及活化. 结果表明,在不同粒径的催化剂上,检测到有CH4解离生成的CHx(x=1～3)物种,以及催化剂表面吸附的CHx物种与表面-OH 作用生成的CHx-O物种. CH4的裂解强烈依赖于催化剂表面Ni颗粒的大小,在粒径8 nm左右的Ni颗粒上, CH4较易解离; CO2难以直接在Ni/SiO2催化剂表面发生解离吸附,但CH4解离生成的吸附H对CO2的解离吸附具有明显的促进作用; CH4与CO2共吸附时,较小粒径的Ni可以促进CO2与表面氧物种发生反应,生成单齿表面碳酸盐物种.     

Rh/SiO_2和Rh/NaY催化剂上合成气反应的高压原位红外光谱研究

采用高压原位FT -IR技术 ,对比研究了CO加H2 反应条件下Rh/SiO2 和Rh/NaY催化剂表面反应中间物种 .在Rh/SiO2 表面上 ,无论在常压还是在 1.0MPa合成气中 ,只观察到线式和桥式吸附CO .而在常压合成气中 ,Rh/NaY上不仅存在上述CO吸附物种 ,而且还有孪生型的Rh(I) (CO) 2 和少量Rh6 (CO) 16 ;当合成气压力升至 1.0MPa后 ,Rh(I) (CO) 2 迅速转化成Rh6 (CO) 16 和在 2 0 42cm-1产生吸收的单核羰基Rh物种 ,与此同时催化剂表面还生成了单齿和双齿乙酸根物种 ;这些在高压下生成的物种在合成气压力重新降回到常压时依然稳定存在 .研究Rh/NaY上合成气反应表面物种与H2 的反应行为表明单齿乙酸根很可能是反应的活性中间物 .这些结果说明Rh/NaY催化剂在高压合成气中的重构是诱发选择生成乙酸反应的基础     

Ni/Al2O3催化剂表面状态对CH4氧化反应的影响

采用瞬变响应技术研究了常压700℃条件下气相O2、Ni/Al2O3催化剂表面上可逆吸附氧物种及催化剂的表面状态对CH4吸附、反应以及CH4部分氧化反应的影响,同时也对CH4部分氧化制合成气反应过程中催化剂表面所处的状态进行了研究.结果表明,如果催化剂表面处于氧化态,CH4不能吸附分解,只能通过RidealEley机理与催化剂表面的吸附氧进行非选择性氧化反应,这将严重影响CH4的转化和目的产物H2、CO的选择性.只有在还原的催化剂上,CH4部分氧化制合成气反应才能高转化、高选择性地进行.在CH4部分氧化制合成气反应过程中,催化剂表面处于还原态,不存在多余的中间氧物种NiO,但存在少量的碳物种,这有利于保持催化剂的还原态和抑制CO2的生成.     

载体对Rh基催化剂上甲烷解离活性的影响

采用脉冲反应技术、原位CO吸附和吡啶吸附红外光谱,考察了Al2O3和SiO2负载的Rh基催化剂上Rh-CeO2相互作用和CH4解离活性.结果表明,载体酸性对Rh-CeO2相互作用有显著影响.Rh/Al2O3催化剂中添加CeO2增加了载体Al2O3的Lewis酸位,使Al2O3接受电子的能力增强,从而降低Rh的电子密度,有利于CH4解离活化.相反,Rh/SiO2催化剂中添加CeO2减少了载体SiO2的Lewis酸位和酸强度,使SiO2难于接受电子,导致Rh的电子密度增加,不利于CH4解离活化.     

Rh/SiO2催化剂上甲烷部分氧化制合成气的核磁共振研究

 利用1H MAS NMR技术,在甲烷部分氧化(POM)制合成气反应条件下研究了Rh/SiO2催化剂上氢与金属的相互作用及反应机理. 结果发现,氢气在Rh/SiO2上解离吸附后可能有四种存在形式: 化学位移为δ=-100～-120的可逆(αM)和不可逆(αI)吸附氢物种,δ=0～-100的“氢云”或“氢雾”形式的氢物种和δ=3.0的溢流氢物种. 溢流氢物种是由可逆吸附的氢物种和“氢云”或“氢雾”状态的氢物种溢流到SiO2上并弱吸附在桥式氧(Si-O-Si)附近而形成的. 溢流氢物种活化晶格氧,形成一种POM反应的活性氧物种OH-. 活性氧物种OH-反溢流到Rh上,并与CH4解离吸附在Rh上的CHx物种反应生成含氧中间物种CHxO. CHxO物种的化学位移为5～7. O2参与CHxO物种的进一步氧化,或补充溢流氢夺取桥式氧后形成的缺陷位上的晶格氧,在高温(973 K)反应条件下,O2可能优先补充缺陷位上的晶格氧,使CHx的氧化按表面反应机理进行.     

Ir/SiO2上甲烷部分氧化制合成气反应的原位时间分辨红外和原位Raman光谱表征

采用原位时间分辨红外光谱和原位显微Raman光谱技术对Ir/SiO₂上甲烷部分氧化(POM)制合成气反应的初级产物和反应条件下催化剂表面物种进行了跟踪考察,实验结果表明,在H₂预还原的新鲜Ir/SiO₂表面,CO是V(CH₄):V(O₂):V(Ar)=2:1:45混合气反应的初级产物,因而甲烷的直接氧化过程是CO生成的主要途径;而在稳态反应条件下,CO生成的途径可能主要来自CO₂和H₂O与催化剂表面积碳物种(CHx)和/或CH₄的反应.催化剂上生成的积碳可能是导致稳态条件下Ir/SiO₂上POM反应机理不同于H₂预还原的新鲜催化剂的主要原因.     

In-Situ FT-IR Investigation Methane to Syngas over of Partial Oxidation of Rh/SiO2 Catalyst

Partial oxidation of methane to syngas （POM） over Rh/SiO2 catalyst was investigated using in-situ FT-IR. When methane interacted with 1.0wt%Rh/SiO2 catalyst, it was dissociated to adsorbed hydrogen and CHx species. The adsorbed hydrogen atoms were transferred to SiO2 surface by ＂spill-over＂ and reacted with lattice oxygen to form surface -OH species. POM mechanism was investigated over Rh/SiO2 catalyst using in-situ FT-IR. It was found that CO2 was formed before CO could be detected when CH4 and O2 were introduced over the preoxidized Rh/SiO2 catalyst, whereas CO was detected before CO2 was formed over the prereduced Rh/SiO2 catalyst.     

Mechanistic study of partial oxidation of methane to syngas using in situ time-resolved FTIR and microprobe Raman spectroscopies

In situ time-resolved Fourier transform infrared (FTIR) and microprobe Raman spectroscopies were used to characterize the reaction mechanisms of the partial oxidation of methane to syngas over SiO(2)- and gamma-Al(2)O(3)-supported rhodium and ruthenium catalysts. The interaction of both pure methane and a methane/oxygen mixture at a stoichiometric feed ratio with an oxygen-rich catalyst surface led to the formation of CO2 and H(2)O as the primary products. For the H(2)-pretreated samples, the reaction mechanisms with the catalysts differ. Only Rh/SiO(2) is capable of catalyzing the direct oxidation of methane to syngas, while syngas formation over Rh/gamma-Al(2)O(3), Ru/SiO(2), and Ru/gamma-Al(2)O(3) can be achieved mainly via a combustion-reforming scheme. The significant difference in the mechanisms for partial oxidation of methane to syngas over the catalysts can be correlated to the differences in the concentration of oxygen species (O(2-)) on the catalyst surface during the reaction, mainly due to the difference in the nature of the metals and supports.     

甲烷在Ni/TiO2催化剂表面的活化

考察了Ni/TiO2催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以TiO2为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对H2的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性.采用脉冲-质谱在线分析等技术,在无气相氧条件下向Ni/TiO2催化剂脉冲CH4,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关.CH4与Ni/TiO2催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ni/TiO2催化剂具有良好的反应活性和抗积碳性能.     

甲烷在Ni/TiO_2催化剂表面的活化

考察了Ｎｉ／ＴｉＯ２催化剂甲烷部分氧化和二氧化碳重整制合成气的反应活性,实验表明,以ＴｉＯ２为载体的镍系催化剂对于甲烷部分氧化制合成气反应具有较好的活性,尤其对Ｈ２的选择性较高,对二氧化碳重整制合成气反应具有较好的低温反应活性．采用脉冲－质谱在线分析等技术,在无气相氧条件下向Ｎｉ／ＴｉＯ２催化剂脉冲ＣＨ４,发现甲烷在催化剂表面的活化（转化）及其氧化产物的选择性与金属催化剂表面氧的浓度密切相关．ＣＨ４与Ｎｉ／ＴｉＯ２催化剂作用过程中存在明显的氢溢流和氧溢流现象,可能是这种溢流效应使得Ｎ／ＴｉＯ２催化剂具有良好的反应活性和抗积碳性能．     

Rh/SiO_2催化剂上甲烷部分氧化制合成气反应机理的研究(英文)

运用ＴＰＳＲ、ＴＲ－ＦＴＩＲ和化学捕获技术（ＣＨ３Ｉ作捕获剂）,探讨了Ｒｈ／ＳｉＯ２催化剂上的ＰＯＭ反应机理,由此提出热分解氧化机理,认为ＣＨｘ（ｘ＝１～３）和ＣＨｘＯ（ｘ＝１～３）可能是反应物种。     

Product oriented oxidative bromination of methane over Rh/SiO2 catalysts

Rh/SiO2 was prepared for the oxidative bromination of methane. The catalyst was prepared by calcination at different temperatures and for different times to obtain catalysts with different specific surface areas for the purposes of producing either CH3Br or CH3Br and CO. It was found that the catalyst having a low specific surface area (calcined at relatively high temperature) favors the selective oxidation of methane to prepare CH3Br, while the catalyst having a high specific surface area favors the deeper partial oxidation of methane, which is good for CH3Br and CO preparation. The 650 h on stream life-time test revealed that the catalytic performance of the 0.4Rh/SiO2--900-10 catalyst was excellent. Both methane conversion and CH3Br selectivity kept increasing trends during the life-time test. No matter how serious was the Rh leaching during the reaction, the 0.4Rh/SiO2--900-10 catalyst did not deactivate at all.     

Product oriented oxidative bromination of methane over Rh/SiO_2 catalysts

Rh/SiO2 was prepared for the oxidative bromination of methane. The catalyst was prepared by calcination at different temperatures and for different times to obtain catalysts with different specific surface areas for the purposes of producing either CH3Br or CH3Br and CO. It was found that the catalyst having a low specific surface area (calcined at relatively high temperature) favors the selective oxidation of methane to prepare CH3Br, while the catalyst having a high specific surface area favors the deeper partial oxidation of methane, which is good for CH3Br and CO preparation.The 650 h on stream life-time test revealed that the catalytic performance of the 0.4Rh/SiO2-900-10 catalyst was excellent.Both methane conversion and CH3Br selectivity kept increasing trends during the life-time test.No matter how serious was the Rh leaching during the reaction,the 0.4Rh/SiO2-900-10 catalyst did not deactivate at all.     

Studies on the Performance and Structure of Supported Catalysts for the Partial Oxidation of Methane to Syngas

The catalytic properties of several supported metal catalysts on different carriers were studied in the partial oxidation of methane (POM) to syngas. In our experiment, supported noble metal catalysts exhibited better performance than the other supported transition metal catalysts. The catalyst performances were significantly influenced by the d-electron configuration of the active metal components and the dispersion of active metal components on the support. A catalyst with a moderate number of unpaired electrons in the d-orbital of the active metal support without obvious acidity or redox activity (e.g. MgO) was suitable for POM performance. The Rh/SiO2 catalyst was the best in the POM reaction, among those investigated. Reaction conditions apparently also affected the POM performance of the catalyst. The conversion of methane and the selectivity for CO increased with the reaction temperature, and a high CH4/O2 ratio was not beneficial for POM performance.