Propane Aromatization over Mo／HZSM—5 Catalysts

Impregnation,mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite ,the structure and surface acidity of the catalysts were studied by means of XRD,FT-IR ,NH3-TPD,TPR and XPS,The effects of Mo content and reaction time on stream on the aromatization of propane were investigated,It was found that the performance of the Mo/HZSM-5 catalst prepared by the hydrothermal treatment method was much better than that of the other two catalysts,For example ,under the reaction conditions of 823 K and 600h^-1, propance conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%,respectively,XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5,and lartger amounts of them could penetrate into the HZSM-5 channel ,as compared with the other two kinds of catalysts,These factors may be responsibled for their high activities for propane aromatization,IR and NH3-TPD studies indicated that the number of Broensted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.     

La／HZSM—5催化剂上丙烷的芳构化反应研究

采用浸渍法和离子交换法制备了La/HZSM-5分子筛催化剂,用于丙烷芳构化反应,利用XRD,SPS,FT－IR,NH3－TPD技术考察了La对HZSM－5分子筛结构和表面酸性的影响,引入La后能显著提高HZSM－5的丙烷芳构化活性,其中由离子交换法得到的催化剂效果最佳,在反应温度550度,空速600h^-1条件下,丙烷转化率和芳烃选择性分别达到94．58％,68．99％,在La/HZSM-5中分子筛结晶度下降,B酸中心减少,L酸中心增多,离子交换法制备的催化剂比浸渍法催化剂的这种变化更显著,同时更有利于La3 进入分子筛孔道内,并与分子筛产生强相互作用,新增加的L酸中心可能是芳构化反应的活性中心。     

Mo/HZSM-5丙烷芳构化催化性能及其吸附量热的研究

采用等量浸渍法制得一系列不同担载量的Ｍｏ／ＨＺＳＭ－５催化剂,运用ＸＲＤ和ＦＴＩＲ方法考察了Ｍｏ物种在催化剂表面的分散状态,首次采用微分吸一热技术对Ｍｏ／ＨｚＳＭ－５催化剂的表面酸性进行表征。同时研究了催化剂对丙烷芳构化的反应活性。结果表明：对于担载Ｍｏ的ＨＺＳＭ－５分子筛催化剂,Ｍｏ物种在ＨＺＳＭ－５分子筛表面上顺序为ＨＺＳＭ－５〉１％Ｍｏ／ＨＺＳＭ－５〉２％Ｍｏ／ＨＺＳＭ－５分子筛本身表面的酸     

高温水蒸气处理对ZnHZSM-5活性中心的影响

应用X-射线衍射、能谱表面分析和吡啶吸附红外光谱研究了高温水蒸气处理对HZSM-5和ZnHZSM-5催化剂的影响，并以丙烷芳构化作为探针反应考查了催化活性中心的变化．高温水蒸气处理对分子筛的结晶度影响不大，但水蒸气处理使得分子筛骨架铝脱出，脱出的铝在表面富集，分子筛锌交换位的骨架铝脱出较难，脱铝导致分子筛的酸性减弱．高温水蒸气处理后的HZSM-5和ZnHZSM-5催化剂的丙烷反应活性都降低，在ZnHZSM－5上丙烯的选择性增加，反映了具有脱氢活性的锌的强L酸中心数目相对B酸中心减少较少，进一步说明了处于离子交换位的锌离子对骨架铝有保护作用     

Studies on Mo／HZSM-5 Complex Catalyst for Methane Aromatization

The influence of adding Fe,Cr,Co,and Ga into 3%Mo/HZSM-5 catalyst on methane aromatization,and the influence of additives ratio on methane conversion,selectivity to hydrocarbons and coke,as well as distribution of aromatics were investigated.The experimental results showed that the addition of Fe,Cr,Co and Ga promoted the dehydrogenation and dissociation of methane.The results of NH3-TPD indicated that the acidity of HZSM-5 was changed by adding Fe and Co components,consequently the catalytic properties of Mo/HZSM-5 were changed.It was also revealed that strong acid sites were the center of methane aromatization.The results of XRD characterization showed that the crystallinity of Mo on ZSM-5 zeolite was increased after adding Fe,Co additives.     

纳米HZSM-5沸石的骨架热稳定性及其作为催化剂的可再生性

采用高温焙烧和积炭失活-空气烧炭再生方法研究了纳米ZSM-5沸石的骨架热稳定性和用纳米HZSM-5沸石制成的芳构化催化剂的再生重复使用性能,还采用XRD、TG、FTIR、NH3-TPD和N2物理吸附,以及C4液化气固定床临氢芳构化反应对沸石和催化剂样品的物化性质作了表征.结果表明:纳米ZSM-5沸石具有良好的骨架热稳定性,在马弗炉的静止空气气氛中恒温焙烧800℃时仍可保持骨架结构.纳米HZSM-5型芳构化催化剂在C4液化气固定床临氢芳构化反应中不但活性稳定性好,而且可以再生重复使用,具有很高的工业应用价值.     

MgO/HZSM-5中MgO分散状态和催化性能的关系

以硝酸镁、醋酸镁为前身物,通过浸渍法制备了不同系列MgO/ HZSM-5催化剂,用XRD、XPS方法研究了MgO在HZSM-5上的分散状态,用NH3-TPD方法考察了催化剂的酸性,用常压连续流动微型反应装置考察MgO/ HZSM-5在甲苯甲醇烷基化反应中的催化性能.发现前身物不同,MgO在HZSM-5上的分散状态也不同,催化剂的活性和选择性与MgO分散状态密切相关.MgO负载量相同时,在以硝酸镁为前身物制备的催化剂中,MgO在HZSM-5内外表面均有分散,催化剂的对位选择性较高,而活性较低;在以醋酸镁为前身物制备的催化剂中,MgO较多分布在HZSM-5外表面,催化剂的活性较高,但选择性较低.使用醋酸镁为前身物,通过二次浸渍和高温水汽处理,适当改变MgO在分子筛表面的分布并使孔道窄化,可在活性降低较少的情况下显著提高催化剂对二甲苯选择性.     

Effect of Fe-Mo promoters on HZSM-5 zeolite catalyst for 1-hexene aromatization

The promotional effect of Fe-Mo species introduced into HZSM-5 (Zeolyst Int., SiO₂/Al₂O₃ ≈ 30) zeolite catalyst by the wetness impregnation method for the 1-hexene aromatization was investigated. The structure and catalytic performance for the aromatization of 1-hexene over xFeyMo-ZSM-5 catalysts in comparison with unmodified HZSM-5 catalysts were studied. The xFeyMo-ZSM-5 catalysts contain fixed loading (5 wt%) and variable Fe/Mo ratio. The catalysts were characterized by BET, ICP-AES, HRSEM-EDS, HRTEM, XRD, FTIR, H₂-TPR, NH₃-TPD, and pyridine DRIFT spectroscopy. The characterization data confirmed the existence of Fe and Mo species in the zeolite matrix. With Fe and Mo species implementation to HZSM-5 zeolite, the amount of the acid sites decreased, but the selectivities to C₉₊ aromatics increased. The catalyst evaluation was performed at 350 °C for 6 h on-stream at atmospheric pressure using a fixed-bed quartz tube reactor. The selectivity to products of different carbon number was affected by the Fe/Mo ratio within the zeolite. It was found the product distribution of grouped fractions of C₁–C₁₇₊ from the liquid product. The results indicate that the optimum ratio of Fe/Mo is 1–1.5. The highest selectivity for gasoline and distillate ranges was obtained for the 2.5wt%Fe2.5wt%Mo- and 3wt%Fe2wt%Mo-ZSM-5 samples, which was higher than that for parent HZSM-5 catalyst.     

稀土对HZSM—5上正己烷芳构化性能的影响

以正己烷为原料,在连续流动常压反应装置上考察了稀土改性HZSM－5沸石催化剂的芳构化和裂解性能,用红光谱,X射线衍射,X光电子能谱等研究了这些离子改性的沸石催化剂的表面性质,比较了机械混合法和浸渍法引入稀土对催化剂性能的影响,稀土可提高混合法制备的改性催化剂的芳构化性能,B酸中心是正已烷构化的活性中心,L酸中心则对正己烷的裂解起重要作用。     

丙烷选择氧化制丙烯醛MoBiTeO/SiO2催化剂中Te组分的作用

用浸渍法制备了一系列不同Te含量的MoBiTeO/SiO2催化剂, 并用XRD、Raman、XPS、NH3-TPD、吡啶吸附FT-IR和催化剂性能评价等方法考察了Te组分对催化剂的结构、酸性及其丙烷选择氧化制丙烯醛性能的影响. 结果表明, 催化剂中Mo氧化物与Te氧化物之间发生了相互作用, 通过形成Mo—O—Te 桥氧键生成了Te多钼酸盐物种,在一定程度上分散了Mo-O活性中心, 同时TeOx具有脱除丙烯α-H、插氧并将其转化为丙烯醛的功能, 因此, 在MoBiO/SiO2催化剂中添加Te组分使丙烯醛选择性有显著的提高. 但是Te的加入同时也使催化剂中B 酸增强, 这不利于丙烯醛生成. 因此, Te添加量有一最佳范围, nTe/nMo为0.05-0.1 时催化剂具有较好的催化性能.     

复合分子筛催化微晶纤维素水解

采用水热晶化法制备了HY/ZSM-5复合分子筛。通过XRD、SEM、N2-吸附脱附、NH3-TPD及吡啶吸附红外光谱等手段表征催化剂的结构和性质。结果表明,HY与HZSM-5复合后HY型分子筛完全被HZSM-5紧密包裹,形成致密的核壳结构。与机械混合物相比,复合分子筛微孔比表面积及孔体积均有所减少,总酸量略高,弱酸量小,而强酸量大,Br9nsted酸量与之相似,而Lewis酸量有所减少。将所制备的HY/ZSM-5复合分子筛催化剂应用于以离子液体氯化1-乙基-3-甲基咪唑鎓([Emim]Cl)为溶剂的纤维素水解反应中,与HY催化的纤维素水解相比,HY/ZSM-5催化纤维素水解反应获得的最佳葡萄糖收率由28.04%提高到38.78%,葡萄糖选择性由28.91%提高至48.29%。     

Non-Oxidative Aromatization of CH4-C_3H_8 over La-Promoted Zn/HZSM-5 Catalysts

The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h-1 and CH4/C3H8 (mol ratio)=5:1. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.     

丙烷选择氧化制丙烯醛MoVTeO/SiO2催化剂结构与性能研究

考察了MoVTeO/SiO₂系列催化剂对丙烷选择氧化制丙烯醛反应的催化性能,结合XRD,Raman和TPD等表征结果研究了催化剂结构、表面性质与催化性能之间的关系.结果表明,以Mo为主要活性组分的催化剂(MoV_0.2Te_0.1/SiO₂)具有较好的催化性能.在V,Te组分存在下,Mo物种的分散度和MoO₃的可还原性能提高.以表面钼酸盐和多钼酸盐类形态存在的高分散Mo物种有助于提高催化活性,而催化剂较弱的表面酸性对丙烯醛的生成有利.     

用于乙烯芳构化反应的Zn/HZSM-5催化剂失活机制研究

采用浸渍法制备了Zn负载量（质量分数）分别为1%、2%、3%的Zn/HZSM-5分子筛催化剂,通过XRD、N₂吸附-脱附、NH₃-TPD、Py-FTIR、XPS、TG-DTA等技术,系统考察Zn/HZSM-5分子筛在乙烯芳构化反应的失活机制。结果表明,积炭是催化剂失活的主要原因,HZSM-5中Zn的添加在较大程度上抑制了催化剂的积炭行为;低Zn含量时催化剂失活缓慢,但Zn含量较高时,由于催化剂比表面积和孔体积极剧下降,催化剂失活加剧。反应过程中,分子筛上Zn物种存在迁移和流失行为,迁移行为体现为催化剂表面Zn的富集和相对比例的变化;Zn流失速率在不同反应阶段保持恒定,但受到Zn含量的影响,Zn含量越高、流失速率越大。外表面ZnO是分子筛催化剂Zn流失的主要物种,且随Zn负载量升高变化趋势愈加明显,其含量与积炭速率存在一定关联。     

W掺杂对Mo/HZSM-5催化甲烷无氧芳构化性能的影响

采用浸渍法制备了Mo/HZSM-5、Mo-W/HZSM-5和W/HZSM-5三种催化剂。通过XRD、BET、Py-FTIR、H2-TPR、XPS、TEM、NH3-TPD、TPO、TG和Raman等技术对催化剂的物化性质进行表征,并考察其在甲烷无氧芳构化反应中的催化性能。结果表明,相比于Mo/HZSM-5,Mo-W/HZSM-5催化剂表现出更高的CH_4转化率、芳烃收率以及催化稳定性。H_2-TPR和XPS结果表明,Mo-W/HZSM-5中存在更易被还原为W~(4+)的正八面体(WO_6)~(n-)前驱体,反应过程中W4+的形成有助于提高CH_4转化率。同时,积炭表征结果表明,石墨型积炭是导致Mo/HZSM-5催化剂快速失活的主要原因,W掺杂可以抑制MoW/HZSM-5催化剂上石墨型积炭的形成,进而提高催化剂的稳定性。     

Thermal and hydrothermal stabilities of the alkali-treated HZSM-5 zeolites

HZSM-5 zeolites with the micro-mesopore hierarchical porosity have been prepared by the post-synthesis of alkali-treatment, and their thermal and hydrothermal stabilities were studied using DTA, XRD, and NH3-TPD characterization techniques. Compared to the unmodified zeolite, the thermal and hydrothermal stabilities of the alkali-treated ZSM-5 zeolites were slightly deteriorated because of the introduction of mesopores caused by the desilication. Nevertheless, the alkali-treated zeolite framework could be maintained until the temperature increased to 1175 ℃.     

MgO改性的HZSM-5酸性和催化作用

以MgO为修饰剂对HZSM - 5沸石进行改性。以XRD、NH3-TPD为手段研究了 (MgO)HZSM - 5酸性并和甲苯甲醇烷基化反应的活性与选择性进行了关联。实验结果表明 ,MgO和HZSM - 5表面有一定的相互作用。HZSM - 5被MgO改性后 ,表面强酸中心减少从而使探针反应的活性下降但选择性提高。     

金属改性P/HZSM-5分子筛催化乙醇芳构化

以P/HZSM-5分子筛为基础, 通过浸渍法制备了Cr、Co、Cu、Zn等金属改性的M-P/HZSM-5分子筛. 采用X射线衍射(XRD), 比表面积(BET)和氨气程序升温(NH₃-TPD)等方法对其进行了表征, 并考察了其催化乙醇芳构化的活性. 结果表明, 改性后的ZSM-5分子筛保持原有的骨架结构, 但比表面积降低, 酸性分布发生变化; Cu-P/HZSM-5分子筛有较高催化活性. P和Cu的负载量分别为3%和5%, 先浸渍P再浸渍Cu, 反应温度400 °C, 质量空速(WHSV)为1.0 h^-1时轻质芳烃(BTX)收率可达到57.6%.     

ZnO—Ga2O3／HZSM—5分子筛催化剂对C3—4烷烃芳构化反应的催化作用

用浸渍法将Ga、Zn以氧化物的形式负载于HZSM－5上,研究了其对C3－4烷烃芳构化的催化活性。结果表明,分别加入2％Ga和2％Zn后,当温度为520℃、空速为0．76h^-1时,具有较高的催化活性和芳烃选择性;反应进行100h后,催化活性无明显降低,显示出对C3－4烷烃芳构化良好的稳定性。用TPD和正丁胺Hammett酸性滴定法,测定了催化剂的表面酸性,发现加入Ga、Zn等组分后,催化剂的总酸量变化不大,而酸强度却有所增加;加入Zn组分后,催化剂的孔径变小,对二甲苯选择性增加。     

Ga2O3/HZSM-5催化剂上丙烷脱氢反应

以直接水热合成和低硅沸石高温水蒸气脱铝两种方法制备了不同Si/Al摩尔比的HZSM-5载体, 考察了Ga₂O₃/HZSM-5催化剂上丙烷脱氢制丙烯的反应性能. 结合XRD, N₂气吸附, ²⁷Al MAS NMR和NH₃-TPD等表征方法, 讨论了催化剂酸性质和孔性质与性能的关系. 实验结果表明, 减少催化剂表面的中强酸量可以显著提高反应的稳定性和丙烯的选择性; 水蒸气脱铝所增加的介孔有同样的效果, 这可能是由于介孔的存在有利于丙烯的脱附和扩散而抑制了寡聚、环化等副反应的发生, 减少了表面积炭的可能性.