Mo/HZSM-5催化剂上甲烷无氧芳构化反应——HZSM-5分子筛脱铝的影响

采用两种不同的脱铝方法对HZSM-5分子筛进行了预处理,并利用MAS NMR和吸附吡啶的FT-IR对分子筛的结构和酸性质进行了表征,考察了分子筛的脱铝程度对Mo基催化剂上甲烷芳构化反应性能的影响.结果表明,HZSM-5分子筛的酸性过强或B酸量不足,均会导致催化剂严重积炭,但积炭成因不同.母体HZSM-5分子筛上的强B酸中心的存在可促使催化剂上反应中间物种深度脱氢,造成催化剂在反应过程中严重积炭.经水热处理的HZSM-5分子筛,骨架铝脱出严重,造成B酸活性中心不足以及部分微孔阻塞,不利于C2中间物种芳构化,导致芳烃选择性显著降低.经高温N2处理的HZSM-5分子筛,骨架铝脱出相对缓和,在消除母体分子筛上强B酸中心的同时,保留了较多的弱B酸中心,既可满足C2中间物种芳构化反应的需要,又可有效抑制催化剂积炭,导致甲烷芳构化反应性能显著改善.     

La／HZSM—5催化剂上丙烷的芳构化反应研究

采用浸渍法和离子交换法制备了La/HZSM-5分子筛催化剂,用于丙烷芳构化反应,利用XRD,SPS,FT－IR,NH3－TPD技术考察了La对HZSM－5分子筛结构和表面酸性的影响,引入La后能显著提高HZSM－5的丙烷芳构化活性,其中由离子交换法得到的催化剂效果最佳,在反应温度550度,空速600h^-1条件下,丙烷转化率和芳烃选择性分别达到94．58％,68．99％,在La/HZSM-5中分子筛结晶度下降,B酸中心减少,L酸中心增多,离子交换法制备的催化剂比浸渍法催化剂的这种变化更显著,同时更有利于La3 进入分子筛孔道内,并与分子筛产生强相互作用,新增加的L酸中心可能是芳构化反应的活性中心。     

分子筛的酸处理对Mo/HZSM-5催化甲烷无氧芳构化反应性能的影响

 采用HNO3溶液对HZSM-5分子筛进行预处理,并以处理后的分子筛为载体制备了Mo/HZSM-5 催化剂. 结果表明,改性的Mo/HZSM-5催化剂在甲烷无氧脱氢芳构化反应中表现出很好的稳定性,显著地抑制了积炭物种在催化剂表面的形成. SEM,XRD和1H MAS NMR等表征结果表明,酸处理在一定程度上降低了HZSM-5分子筛的结晶度,使部分Al物种脱离骨架结构,迁移到骨架外形成新的表面Al羟基,从而使HZSM-5分子筛上B酸中心的数目明显减少. 未经改性的Mo/HZSM-5催化剂表面,平均每个晶胞中有1.12个B酸位,而改性的Mo/HZSM-5催化剂表面,平均每个晶胞中仅有0.88个B酸位. 这表明过多的酸性位存留在催化剂上会引起积炭的生成,降低催化剂的稳定性.     

HZSM-5沸石中Lewis酸与Brönsted酸协同作用下的甲基环己烷开环反应

由于水蒸气处理HZSM-5生成的骨架外铝在分子筛中体现Lewis酸性, 分子筛中骨架外铝物种的可移动性导致Lewis酸与分子筛本身的Brönsted酸在空间上具有临近性. 当甲基环己烷分子在HZSM-5的笼中转化时, Lewis酸与Brönsted酸的协同作用加快了甲基环己烷分子的转化速率, 且骨架外铝物种浓度越高, 这种协同效应越明显. 而产物的选择性只与催化剂的孔道结构有关, 与水蒸气处理所导致的酸性质的变化无关.     

硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响

 结合催化剂的活性评价及固体高分辨核磁共振谱、X射线光电子能谱和X射线荧光光谱和热重等技术,考察了硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响. 结果表明,采用大分子有机硅烷对HZSM-5分子筛进行硅烷化处理,除去了分子筛外表面的酸性位,并使分子筛本身发生了脱铝. 硅烷化处理使Mo/HZSM-5催化剂在进行甲烷脱氢芳构化反应时催化剂上总的积碳量明显减少,从而提高了催化剂的活性.     

硅烷化处理对Moo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响

结合催化剂的活性评价及固体高分辨核磁共振谱、X射线光电子能谱和X射线荧光光谱和热重等技术,考察了硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响.结果表明,采用大分子有机硅烷对HZSM-5分子筛进行硅烷化处理,除去了分子筛外表面的酸性位,并使分子筛本身发生了脱铝.硅烷化处理使Mo/HZSM-5催化剂在进行甲烷脱氢芳构化反应时催化剂上总的积碳量明显减少,从而提高了催化剂的活性.     

ZSM-5的水热改性及其在合成气经二甲醚制汽油中的应用

对合成气经二甲醚制汽油两段等压反应系统中的ZSM-5分子筛催化剂进行原位水热处理,研究了不同温度下水蒸气处理ZSM-5分子筛的结构、表面酸性及催化反应性能。XRD、XRF、BET、NH₃-TPD 和 TPO等表征手段表明,水热处理温度为400℃时会使ZSM-5分子筛大部分非骨架铝脱除,酸中心数量减少,比表面积增加,提高了催化剂的活性及产物选择性。     

固体高辨核磁共振技术对改性金属离子在HZSM-5分子筛中的行为研究

使用固体高分辨核样共振技术研究Zn^2+, Ga^3+,等离子在HZSM-5分子筛中的行为。结果表明, Ga^3+离子主要定位于HZSM-5外表面, 不能抑制骨架脱铝; Zn^2+离子进入了HZSM-5内孔道, 取代了桥羟基上部分质子位, 能稳定沸石骨架。Ga^3+,Zn^2+离子均未进入沸石骨架位。骨架脱铝顺序为: GaHZSM-5>ZnHZSM-5》BaHZSM-5≌CaHZSM-5。     

氟氯有机化合物对分子筛催化剂的改性——Ⅰ.CF_2Cl_3对HZSM-5分子筛改性的研究

对经CF_2Cl_2处理了不同时间的HZSM-5分子筛,采用XRD,IR,XPS,SEM和TPD等方法考察了其结构和表面性质的变化。发现B酸位减少的同时,中等强度的B酸位的分数有所提高,沸石表面不但脱铝也有脱硅现象发生。这种改性的HZSM-5分子筛对异丙苯裂化反应及偏三甲苯-甲醇烷基化合成均四甲苯反应的活性、选择性及催化剂的稳定性都有良好的促进作用。     

酸碱处理对ZSM-5分子筛物化性质和反应性能的影响

考察了碱处理、先碱后两步酸处理对HZSM-5分子筛物化性质以及苯与甲醇烷基化反应性能的影响。结果表明,碱处理在脱除分子筛中非骨架硅的同时,提高了晶孔的利用率,也中和了分子筛的强酸中心,使催化剂活化甲醇的能力减弱,苯与甲醇反应活性降低;先碱后两步酸处理既脱除了分子筛中的非骨架铝,也恢复了一部分强酸中心,提高了苯与甲醇的反应活性。进一步考察了先碱后两步酸处理中不同碱浓度的影响,结果表明,适宜浓度的碱处理后再两步酸处理,一方面,能脱除分子筛的非骨架硅铝物种,使分子筛的颗粒粒径更加均匀;另一方面,分子筛的强酸中心有所减少,降低了催化剂的积炭失活速率,苯转化率提高15%以上。     

27Al和29Si MAS-NMR对Mo/HZSM-5催化剂的研究

使用＾２９Ａｌ固体离分辨核磁技术对甲烷无氧芳构化催化剂Ｍｏ／ＨＺＳＭ－５分子筛进行了研究，发现ＨＺＳＭ－５分子筛本体中仅含有少量非骨架Ａｌ，Ｍｏ物种与分子筛骨架Ａｌ的相互作用随Ｍｏ担载量以及焙烧的温度的升高而增加，在高温焙烧下，Ｍｏ物种会使分子筛骨架严重脱铝，并且生成Ａｌ２（ＭｏＯ４）３新相，最终导致分子筛骨架塌陷，催化性能下降。     

ZSM—5芳构化反应活性和稳定性的研究

ＺＳＭ－５以其独特的基于微孔结构特征的形状选择性和强酸中心，而成为具有酸催化择形性能的新型分子筛催化剂．ＺＳＭ－５分子筛表面酸性中心不但是反应的活性中心，同时也是积炭中心，这使得这类催化剂不仅具有很高的催化反应活性，同时也具有较高的结焦活性．催化剂表...     

Methane dehydrogenation and aromatization in the absence of oxygen on Mo/HZSM-5: A study on the interaction between Mo species and HZSM-5 by using Al and Si MAS NMR

By using a high-resolution solid state nuclear magnetic resonance spectrometer with ²⁷Al and ²⁹Si probes, the interaction between Mo species and HZSM-5 of frsol|Mo/HZSM-5 catalysts has been studied. The results show that there is a strong interaction between Mo species and HZSM-5 zeolite. The framework aluminum in the zeolite can be easily extracted by the introduction of Mo species. The extractability of framework aluminum by Mo species increases with increasing Mo loading and the calcination temperature. The extraction process leads to the formation of non-framework Al at first and then a new crystalline phase of Al₂(MoO₄)₃. The dealumination of the catalyst having a Mo loading of 15% and had been calcined at 973 K is so severe that all the aluminum in the framework are extracted and no framework Al could be detected by ²⁷Al MAS NMR. The catalyst, therefore, lost its catalytic activity for methane dehydrogenation and aromatization in the absence of oxygen. The Si/Al ratio measured from ²⁹Si MAS NMR further confirms the dealumination process observed by ²⁷Al MAS NMR. The MAS NMR results give us an evidence that Al₂(MoO₄)₃ crystallites are much less active for the reaction.     

Study of the properties of pentasil-containing catalysts in reactions of transformation of hydrocarbons

The kinetics of transformations of propane and propylene on pentasils modified with zinc, Zn/HTsVM, and the H form of zeolite were investigated. Quantitative data were obtained which revealed significant differences for HTsVM and Zn-containing catalysts in the selectivity of transformations of propane with different degrees of its conversion. The promoting effect of Zn in the Zn/HTsVM system not only on the stage of dehydrogenation of propane into propylene, but also on subsequent transformations of propylene into aromatic hydrocarbons, was demonstrated. The absence of internal diffusion inhibition of the reaction in the conditions studied was demonstrated experimentally. It was shown that aromatization of propane takes place in the kinetic region.For previous communication, see [1].Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 4, pp. 727–733, April, 1990.     

甲烷在含镓沸石（MFI）上无氧活化性能的研究

采用水热法合成了不同Ｓｉ／Ａｌ、Ｓｉ／Ｇａ比的含镍分子筛，催化反应活性表征结果表明，地丙烷芳构化反应具有良好催化活性的含镍分子。没有显示出任何催化甲烷芳构化反应的特性；ＭｏＯ３作为添加组分显著地改变了催化剂的反应性能，３％ＭｏＯ３负载的含Ｇａ分子筛，在９７３Ｋ温度给出了约６％甲烷转化率和大于８０％的芳烃选择性，与ＺＳＭ－５相比，城相同的ＭｏＯ３担载条件下，含Ｇａ分子筛催化剂甲烷芳构化活性较低，但是     

用于乙烯芳构化反应的Zn/HZSM-5催化剂失活机制研究

采用浸渍法制备了Zn负载量（质量分数）分别为1%、2%、3%的Zn/HZSM-5分子筛催化剂,通过XRD、N₂吸附-脱附、NH₃-TPD、Py-FTIR、XPS、TG-DTA等技术,系统考察Zn/HZSM-5分子筛在乙烯芳构化反应的失活机制。结果表明,积炭是催化剂失活的主要原因,HZSM-5中Zn的添加在较大程度上抑制了催化剂的积炭行为;低Zn含量时催化剂失活缓慢,但Zn含量较高时,由于催化剂比表面积和孔体积极剧下降,催化剂失活加剧。反应过程中,分子筛上Zn物种存在迁移和流失行为,迁移行为体现为催化剂表面Zn的富集和相对比例的变化;Zn流失速率在不同反应阶段保持恒定,但受到Zn含量的影响,Zn含量越高、流失速率越大。外表面ZnO是分子筛催化剂Zn流失的主要物种,且随Zn负载量升高变化趋势愈加明显,其含量与积炭速率存在一定关联。     

Zn/HZSM-5分子筛催化剂对丙烷芳构化反应中芳烃分布的影响

采用浸渍法,制备了Ｚｎ／ＨＺＳＭ－５分子筛催化剂,考察了锌含量、反应温度对丙烷芳构化反应的影响,根据产物分布情况,讨论了锌物种在丙烷芳构化反应中的作用,并以氮气作载气,带入烷基芳烃乙苯、二甲苯、甲苯,考察了温度对催化剂脱烷基反应的影响。结果表明,锌物种不公能够催化丙烷的脱氢活化,提高其转化率,而且能促进随后进行的齐聚、脱氢芳构化第一系列反应,提高芳烃的选择性,并进一步催化烷基芳烃的脱烷基反应,导致     

Ga改性ZSM-5分子筛催化丙烷芳构化性能研究

用离子交换法制备Ga改性ZSM-5双功能催化剂,并结合XRD、SEM、BET、NH₃-TPD、Py-IR及ICP、XPS等多种技术进行表征,考察分子筛硅铝比(Si/Al)和催化剂氧化还原预处理条件对分子筛的酸性质、Ga物种的存在状态及其丙烷芳构化催化性能的影响。研究表明,硅铝比不仅可以改变分子筛的酸性,也会影响分子筛中非骨架Ga物种与分子筛表面的相互作用程度,进而影响含Ga分子筛的丙烷芳构化性能。在质量空速1.0 h^-1、反应温度550℃ 下,Si/Al比为30的Ga-HZSM-5分子筛丙烷转化率和芳烃收率最高。Ga物种的引入可以提高丙烷的转化率和芳烃的选择性,并抑制烷烃、烯烃的裂解。H₂还原处理,将分子筛表面Ga₂O₃还原为低价的Ga⁺和GaH⁺₂物种,促进了Ga物种向分子筛微孔迁移;还原-氧化处理后,Ga⁺和GaH⁺₂物种氧化成GaO⁺,占据分子筛孔道离子交换位,显著提高了催化剂的芳构化活性。     

Propane Aromatization over Mo／HZSM—5 Catalysts

Impregnation,mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite ,the structure and surface acidity of the catalysts were studied by means of XRD,FT-IR ,NH3-TPD,TPR and XPS,The effects of Mo content and reaction time on stream on the aromatization of propane were investigated,It was found that the performance of the Mo/HZSM-5 catalst prepared by the hydrothermal treatment method was much better than that of the other two catalysts,For example ,under the reaction conditions of 823 K and 600h^-1, propance conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%,respectively,XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5,and lartger amounts of them could penetrate into the HZSM-5 channel ,as compared with the other two kinds of catalysts,These factors may be responsibled for their high activities for propane aromatization,IR and NH3-TPD studies indicated that the number of Broensted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.     

Promoted effect of zinc–nickel bimetallic oxides supported on HZSM-5 catalysts in aromatization of methanol

Zn/ZSM-5(NZ2) and Zn/Ni/ZSM-5(NZ3) as the catalysts for methanol to aromatics(MTA) were synthesized by a simple ultrasonic impregnation. The textural and acid properties of all catalysts were characterized using XRD, HRTEM, NH_3-TPD, Py-IR, XPS, XRF and TG techniques. The XRD and HRTEM results showed that the basic zeolite structures were not affected much with the incorporation of Zn and Ni species. However, great changes have taken place in acid properties. The Py-IR and XPS results indicated that the Zn-Lewis acid sites(ZnOH~+ species), which have stronger interaction with the zeolite framework compared with ZnO species, were generated at the expense of B acid sites with the incorporation of zinc species. Moreover, the product analysis results showed that the incorporation of zinc species promoted the primary aromatization by enhancing the dehydroaromatization and suppressing the cracking and subsequent H-transfer reaction. Furthermore, the addition of Ni species well inhibited the loss of zinc species by converting partial ZnO species to ZnOH~+ species, and thus improved the aromatization activity and catalyst stability. The catalytic performance results showed that the NZ3 possess higher conversion of methanol in a longer time and lower average rate of coke formation compared with NZ2. In addition,the NZ3 also exhibited the highest yield of BTX as the reaction proceeds.