In改性Mo/HZSM-S催化剂上的甲烷芳构化反应性能

Dehydrogenation and aromatization of methane over Mo/HZSM-5 catalyst without adding oxygen were widely studied［1～3］. However, the existing problem of this route is the low yield of aromatics, owing to the high stability of methane. Recently, the introduction of the second metal species was believed to be a promising route to improve non-oxidative transformation of methane over Mo/HZSM-5 catalyst[4-7].     

Effect of Dimethyl Ether Co-feed on Catalytic Performance of Methane Dehydroaromatization over Mo／HZSM-5 Catalyst

The effect of dimethyl ether (DME) co-feed on the catalytic performance of methane dehydroaxomatization (MDA) over 6Mo/HZSM-5 catalyst was investigated as a function of DME concentration under reaction conditions of T=1023 K, p=101 kPa and SV=1500 ml/(g.h). A high benzene yield wasobtained and the stability of the catalyst was improved by adding 1.5%DME to the CH4 feed. The C6H6 yield was as high as ca. 10% even after reaction for 6 h. The stability of the catalyst was further improved when DME concentration in the co-feed gas was increased to an appropriate value. TGA and TPO results of the used 6Mo/HZSM-5 catalyst showed that the amount of coke on the used catalyst was reduced and the chemical nature of the coke was changed. When 1.5%DME was added to the CH4 feed, the coke formed on the catalyst could be burned off more easily than that when only CH4 was used as reactant. It is supposed that the oxygen in DME may play a role in preventing the coke burnt off at lower temperature from transforming into the coke burnt off at higher temperature, which results in the improvement of the stability of the catalyst.     

Influence of Pretreatment Conditions on Methane Aromatization Performance of Mo／HZSM—5 and Mo—Cu／HZSM—5 Catalysts

Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditions has been studied. The results indicate that the catalyst presented a distinguished catalytic activity, benzene selectivity and a high stability when the bed temperature was raised in N2 atmosphere.     

Propane Aromatization over Mo／HZSM—5 Catalysts

Impregnation,mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite ,the structure and surface acidity of the catalysts were studied by means of XRD,FT-IR ,NH3-TPD,TPR and XPS,The effects of Mo content and reaction time on stream on the aromatization of propane were investigated,It was found that the performance of the Mo/HZSM-5 catalst prepared by the hydrothermal treatment method was much better than that of the other two catalysts,For example ,under the reaction conditions of 823 K and 600h^-1, propance conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%,respectively,XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5,and lartger amounts of them could penetrate into the HZSM-5 channel ,as compared with the other two kinds of catalysts,These factors may be responsibled for their high activities for propane aromatization,IR and NH3-TPD studies indicated that the number of Broensted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.     

Methane dehydro-aromatization over Mo/HZSM-5 catalysts in the absence of oxygen: Effect of steam-treatment on catalyst stability

The effect of steam-treatment to HZSM-5 zeolite and Mo/HZSM-5 with a steaming time range of 0.5-1 h on the catalytic performance of methane dehydro-aromatization (MDA) over Mo/HZSM-5 catalyst prepared with impregnation has been studied in detail in combination with the characterization of 1H MAS NMR technique. Both the deactivation rate constant (kd) and the Brnsted acid sites per unit cell were calculated to quantitatively evaluate the stability of Mo/HZSM-5 catalysts treated with steam at 813 K before and after impregnation of molybdenum species, and the corresponding variation of their Brnsted acid sites. The results reveal that a V-shape relationship between kd and the number of B1 acid sites per unit cell is presented on Mo/HZSM-5 catalyst under the tested steam-treatment and reaction conditions.     

Methane Direct Conversion on Mo/ZSM-5 Catalysts Modified by Pd and Ru

The effect of addition of Ru and Pd to Mo/HZSM-5 catalysts used in the dehydroaromatiza-tion of methane was investigated. Catalytic tests and temperature-programmed oxidation results showed that Pd-based catalysts were more selective to naphthalene and suffered strong deactivation. The presence of Ru improved the activity and stability, with a decrease in the carbonaceous deposit probably because of a mechanism of protection of the Mo2C surface.     

Propane Aromatization over Mo/HZSM-5 Catalysts

Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsi     

Comparison of the activities of binder-added and binder-free Mo/HZSM-5 catalysts in methane dehydroaromatization at 1073 K in periodic CH4-H2 switch operation mode

Three industry-supplied,well-shaped Mo/HZSM-5 catalysts,two binder-added and one binder-free,were tested for the first time in methane dehydroaromatization to benzene at 1073 K and 10000 mL/(g h)in periodic CH4-H2 switch operation mode,and their catalytic performances were compared with those of three self-prepared,binder-free powder Mo/HZSM-5 catalysts.XRD,27Al NMR,SEM,BET and NH3-TPD characterizations of all the catalysts show that the zeolites in the two binder-added catalysts are comparable to those in the three binder-free powder catalysts in crystallinity,crystal size,micropore volume and Brnsted acidity.The test results,on the other hand,show that the catalytic performances of the two binder-added catalysts are worse than those of the four binder-free catalysts on both catalyst mass and zeolite mass bases.Then,TPO and BET measurements of all spent samples were conducted to get a deep insight into the negative effects of binder addition, and the results suggest that the binder additives functioned mainly to enhance the polyaromatization of formed aromatics to coke on their external surfaces and consequently lower the benzene formation activity and selectivity of the catalyst.     

Effects of Calcination Temperature on the Acidity and Catalytic Performances of HZSM-5 Zeolite Catalysts for the Catalytic Cracking of n-Butane

The acidic modulations of a series of HZSM-5 catalysts were successfully made by calcination at different treatment temperatures, i.e. 500, 600, 650, 700 and 800 ℃, respectively. The results indicated that the total acid amounts, their density and the amount of B-type acid of HZSM-5 catalysts rapidly decreased, while the amounts of L-type acid had almost no change and thus the ratio of L/B was obviously enhanced with the increase of calcination temperature (excluding 800 ℃). The catalytic performances of modified HZSM-5 catalysts for the cracking of n-butane were also investigated. The main properties of these catalysts were characterized by means of XRD, N2 adsorption at low temperature, NH3-TPD, FTIR of pyridine adsorption and BET surface area measurements. The results showed that HZSM-5 zeolite pretreated at 800 ℃ had very low catalytic activity for n-butane cracking. In the calcination temperature range of 500-700 ℃, the total selectivity to olefins, propylene and butene were increased with the increase of calcination temperature, while, the selectivity for arene decreased with the calcination temperature.The HZSM-5 zeolite calcined at 700 ℃ produced light olefins with high yield, at the reaction temperature of 650 ℃ the yields of total olefins and ethylene were 52.8% and 29.4%, respectively. Besides, the more important role is that high calcination temperature treatment improved the duration stability of HZSM-5zeolites. The effect of calcination temperature on the physico-chemical properties and catalytic performance of HZSM-5 for cracking of n-butane was explored. It was found that the calcination temperature had large effects on the surface area, crystallinity and acid properties of HZSM-5 catalyst, which further affected the catalytic performance for n-butane cracking.     

甲烷芳构化Mo／HZSM—5催化剂上添加第二组分的研究

研究了在3％Mo/HZSM-5催化剂上添加Fe、Cr、Co、Ga助剂对甲烷芳构化反应的影响,以及添加的物料比与甲烷转化率、碳氢化合物和焦炭的选择性、苯产物分布的关系。结果表明,添加Fe、Cr、Co、Ga金属助剂,调整了HZSM－5的酸性,从而改变了催化剂的活性,XRD 结果表明,添加了Co、Fe助剂的催化剂,使用后其HZSM－5分子筛的晶相结构发生了变化。     

甲烷在含镓沸石（MFI）上无氧活化性能的研究

采用水热法合成了不同Ｓｉ／Ａｌ、Ｓｉ／Ｇａ比的含镍分子筛，催化反应活性表征结果表明，地丙烷芳构化反应具有良好催化活性的含镍分子。没有显示出任何催化甲烷芳构化反应的特性；ＭｏＯ３作为添加组分显著地改变了催化剂的反应性能，３％ＭｏＯ３负载的含Ｇａ分子筛，在９７３Ｋ温度给出了约６％甲烷转化率和大于８０％的芳烃选择性，与ＺＳＭ－５相比，城相同的ＭｏＯ３担载条件下，含Ｇａ分子筛催化剂甲烷芳构化活性较低，但是     

碳四烃在改性HZSM-5分子筛上芳构化研究

研究了炼厂混合C_4烃在Zn、Ga、Cr、La改性的HZSM-5分子筛催化剂上的芳构化反应,采用TPD和IR测定了催化剂的表面酸性质。结果表明,用Zn(3%)和Zn(2%)Ga(1%)改性的HZSM-5分子筛具有较好的芳构化性能;各改性HZSM-5分子筛催化剂芳构化性能变化与表面酸性有关,总酸量下降,芳构化活性下降,强B酸中心减少,深度裂解反应减少;Zn的单组分和双组分改性的HZSM-5分子筛催化剂芳构化活性的增高与表面强L酸浓度增加和吡啶吸附IR谱中的1615cm~(-1)吸收峰出现有关。     

甲烷芳构化反应催化剂的研究——Mo-M/HZSM-5在无氧条件下的催化性能和表面性质

苯;甲烷芳构化反应催化剂的研究——Mo-M/HZSM-5在无氧条件下的催化性能和表面性质     

甲烷在MoO_3／HZSM－5分子筛催化剂上的非氧催化转化

研究了反应温度、空速、Ｍｏ担载量和焙烧温度对ＭｏＯ３／ＨＺＳＭ－５催化剂上甲烷的芳构化反应的影响．ＨＺＳＭ－５分子筛的Ｂｒｏｎｓｔｅｄ酸性、孔道结构和Ｍｏ在分子筛中的分布是影响催化性能的重要因素．ＨＺＳＭ－５上Ｍｏ担载量为２～３％时活性最佳，在１０１３Ｋ反应温度下甲烷转化率可达９％，芳烃选择性大于９０％．空速影响的实验表明乙烯是反应的初始产物．在此基础上提出了＂甲烷酸助异裂活化＂的新概念、＂金属钼类碳烯中间物＂的新观点和甲烷芳构化的可能机理．     

甘油辅助HZSM-5分子筛的制备及其甲烷无氧芳构化催化性能研究

以正硅酸乙酯(TEOS)为硅源,甘油为辅助剂,在水热条件下合成HZSM-5分子筛。考察甘油添加量、晶化时间对HZSM-5分子筛的晶粒尺寸、相对结晶度和酸性等性质及其甲烷无氧芳构化催化性能的影响。利用X射线衍射(XRD)、扫描电镜(SEM)、氨程序升温脱附(NH_3-TPD)等分析手段对不同条件合成的HZSM-5分子筛样品进行表征。结果表明,在添加一定量的甘油辅助剂的条件下,通过调控晶化时间,可以提升HZSM-5分子筛的相对结晶度,在一定程度上抑制无定型SiO_2的产生,增加其酸量。在甲烷无氧芳构化反应中,甘油辅助合成的HZSM-5分子筛催化剂表现出优良的催化性能,与未添加甘油合成的HZSM-5分子筛催化剂相比,甲烷转化率、苯选择性和芳烃选择性均有较大提高,且具有较强的稳定性与容炭能力。     

Methane Aromatization Under O2-Free Conditions on Zinc Modified Mo/HZSM-5 Catalyst

The influence of Zn content, reaction temperature and pretreatment conditions on a Zn-modified Mo/HZSM-5 catalyst for methane aromatization were studied. It was found that the addition of Zn promoted the reaction. Methane conversion of 10.9% and aromatics selectivity of 96.7% were obtained with a Zn/Mo molar ratio of 0.03 and N₂ pretreatment at 973 K. The results of isopropanol decomposition, NH₃-TPD and TG-DTA suggest that the addition of Zn decrease the acidity of the catalyst, which may be the reason for the high activity on the Mo-Zn/HZSM-5 catalyst. This revised version was published online in June 2006 with corrections to the Cover Date.     

Non-oxidative aromatization of C1 to C3 hydrocarbons over Pd-promoted Ga/HZSM-5 catalyst under mild conditions

The Pd-promoted Ga/HZSM-5 catalyst was prepared by impregnation method and its catalytic activity for non-oxidativearomatization of C1 to C3 hydrocarbons was assessed using a microreactor-GC system operated with temperature at 823 K andspace velocity at 410 h1.The catalyst is more catalytically active for methane conversion than Ga/HZSM-5.The massspectroscopy analyses confirmed that13CH4 was converted to aromatic products.